Magnus, (reposting with zipped version of adapter.c) Hard_temac_v3_00_b was created to fix a compatibility problem in the MDIO interface for V4FX production silicon (CES4 or later). Unfortunately, it does not work well with silicon that is pre-CES4, which is true of all ML403 boards.
The bottom line is that you should adhere to the following comment: * Note also a silicon issue with Xilinx V4FX with regards to MDIO access: * pre-CES4 chips (ML403, pre-production ML405/ML410) * use hard_temac_v3_00_a * CES4 or later chips (production ML405, ML410 boards) * use hard_temac_v3_00_b I've also attached a new adapter.c that does a slightly better job with the PHY speed negotiation. This one will be shipped in EDK 9.1.1. Thanks, Rick -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Magnus Hjorth Sent: Thursday, January 25, 2007 8:58 AM To: [email protected] Subject: Re: ML403 hard Ethernet under Linux 2.6.18 jozsef imrek wrote: > On Thu, 25 Jan 2007, Magnus Hjorth wrote: > > >> Hi, >> >> I'm trying to get Linux 2.6.18.6 working on an ML403 board with a basic >> EDK design with a hard_temac and uart. I've generated the BSP for >> linux_2_6, copied the drivers and twiddled a little to make it all compile. >> >> The TEMAC driver seems to find the hardware, but the speed negotiation >> seems not to work. I can see the speed LEDs first go to 100 Mbit, then >> ... >> > > i suppose you are using plb_temac 3.00, with the corresponding driver. > plb_temac 3.00.a and hard_temac 3.00.b. The driver is the one that was generated in the BSP using Xilinx EDK 8.2, adapter.c says v2.00b. The only code that I have added myself is a header file xio.h containing: #include <asm/io.h> #define XIo_In32(p) in_be32((volatile void *)p) #define XIo_Out32(p,v) out_be32((volatile void *)p,v) #define XIo_Out8(p,v) out_8((volatile void *)p,v) > did you try to uncomment #define XILINX_PLB_TEMAC_3_00A_ML403_PHY_SUPPORT > in adapter.c ? > > I did try that, and it seems to work even worse. It claims the speed is set to 10Mbit but the LEDs show it's still in 100Mbit operation as it is directly after programming the FPGA... The transmit LED is on for a short while before the Link carrier lost message. Startup messages shown below. loaded at: 00400000 004B613C board data at: 004B4124 004B413C relocated to: 00404094 004040AC zimage at: 00404EA7 004B3CFC avail ram: 004B7000 03D09000 Linux/PPC load: console=ttyS0,9600 ip=on Uncompressing Linux...done. Now booting the kernel Linux version 2.6.18.6mh1 ([EMAIL PROTECTED]) (gcc version 3.4.1) #14 7 Xilinx ML403 Reference System (Virtex-4 FX) Built 1 zonelists. Total pages: 15625 Kernel command line: console=ttyS0,9600 ip=on Xilinx INTC #0 at 0x41200000 mapped to 0xFDFFE000 PID hash table entries: 256 (order: 8, 1024 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Memory: 60184k available (1148k kernel code, 448k data, 68k init, 0k highmem) Mount-cache hash table entries: 512 NET: Registered protocol family 16 NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -1, 2048 bytes) TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250.0: ttyS0 at MMIO 0x40401003 (irq = 1) is a 16550A XTemac: using FIFO direct interrupt driven mode. eth0: Xilinx TEMAC #0 at 0x81200000 mapped to 0xC4000000, irq=0 eth0: XTemac id 1.0f, block id 5, type 8 TCP bic registered NET: Registered protocol family 1 eth0: XTemac: Options: 0xb8f2 eth0: XTemac: speed set to 10Mb/s Sending DHCP requests .<6>eth0: XTemac: PHY Link carrier lost. ..... timed out! IP-Config: Reopening network devices... eth0: XTemac: Options: 0xb8f2 eth0: XTemac: speed set to 10Mb/s Sending DHCP requests ...... timed out! IP-Config: Reopening network devices... eth0: XTemac: Options: 0xb8f2 -- Magnus Hjorth, M.Sc. Omnisys Instruments AB Gruvgatan 8 SE-421 30 Västra Frölunda, SWEDEN Phone: +46 31 734 34 09 Fax: +46 31 734 34 29 http://www.omnisys.se _______________________________________________ Linuxppc-embedded mailing list [email protected] https://ozlabs.org/mailman/listinfo/linuxppc-embedded
adapter.tar.gz
Description: adapter.tar.gz
_______________________________________________ Linuxppc-embedded mailing list [email protected] https://ozlabs.org/mailman/listinfo/linuxppc-embedded
