linuxppc-embeddeHi ALL,
I am porting MPC8245 kernel-2.4.25 from ELDK version 3.1.1.
This CPU(MPC8245) is 300MHz, kernel calibrate MIPS is 200.
Do anyone know this MIPS is right?
U-Boot 1.1.2 (Jan 25 2005 - 14:55:00) [svm]
CPU: MPC8245 Revision 1.1 at 299.999 MHz: 16 kB I-Cache 16 kB D-Cache
Board: SVM_SC8245 Local Bus at 99.999 MHz
I2C: ready
DRAM: Scan SDRAM memory........................
64 MB
Top of RAM usable for U-Boot at: 04000000
Reserving 460k for U-Boot at: 03f8c000
Reserving 128k for malloc() at: 03f6c000
Reserving 56 Bytes for Board Info at: 03f6bfc8
Reserving 48 Bytes for Global Data at: 03f6bf98
Stack Pointer at: 03f6bf78
New Stack Pointer is: 03f6bf78
Now running in RAM - U-Boot at: 03f8c000
FLASH: 512 kB
PCI Scan: Found Bus 0, Device 22, Function 0
PCI Config: I/O=0x80000000, Memory=0x80000000, Command=0x7
00 16 10ec 8139 0200 0b
PCI Scan: Found Bus 0, Device 23, Function 0
PCI Config: I/O=0x81000000, Memory=0x81000000, Command=0x7
00 17 8086 1209 0200 0c
PCI Scan: Found Bus 0, Device 24, Function 0
00 18 8086 1209 0200 0e
In: serial
Out: serial
Err: serial
U-Boot relocated to 03f8c000
DOC: No DiskOnChip found
Net: rtl8139: REALTEK RTL8139 @0x80000000(80000000)
i82559#0
Warning: i82559#0 MAC addresses don't match:
Address in SROM is 00:AA:00:91:6D:94
Address in environment is EE:CC:7C:7E:65:97
, i82559#1, RTL8139#0
### main_loop entered: bootdelay=2
### main_loop: bootcmd="tftpboot 0x210000 kernel-sc82xx-2.4.25-eldk;bootm 0x2100
00"
Hit any key to stop autoboot: 0
Trying i82559#0
Using i82559#0 device
TFTP from server 192.168.0.82; our IP address is 192.168.0.215
Filename 'kernel-sc82xx-2.4.25-eldk'.
Load address: 0x210000
Loading: #################################################################
#################################################################
###########
done
Bytes transferred = 718901 (af835 hex)
## Booting image at 00210000 ...
Image Name: Linux-2.4.25
Created: 2005-07-29 5:42:02 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 718837 Bytes = 702 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Current stack ends at 0x03F6BBE8 => set upper limit to 0x00800000
## cmdline at 0x007FFF00 ... 0x007FFF7E
bd address = 0x03F6BFC8
memstart = 0x00000000
memsize = 0x04000000
flashstart = 0xFFF00000
flashsize = 0x00080000
flashoffset = 0x00068000
sramstart = 0x00000000
sramsize = 0x00000000
bootflags = 0x00000001
intfreq = 299.999 MHz
busfreq = 99.999 MHz
ethaddr = EE:CC:7C:7E:65:97
IP addr = 192.168.0.215
baudrate = 115200 bps
No initrd
## Transferring control to Linux (at address 00000000) ...
Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb
Linux version 2.4.25 (liu at bighead) (gcc version 3.3.3 (DENX ELDK 3.1.1
3.3.3-9))
#2 ? 7? 29 13:41:52 CST 2005
sc82xx_setup_arch:Reserved 0x10000 memory at 0xc01b4000
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: root=/dev/nfs rw nfsroot=192.168.0.82:/prj/sc8245/root cons
ole=ttyS0,115200 ip=192.168.0.215:192.168.0.82:::itogether:eth0:off
OpenPIC Version 1.2 (1 CPUs and 7 IRQ sources) at fdfd0000
bi_intfreq:299999997 bi_busfreq:99999999
Calibrating delay loop... 199.88 BogoMIPS
Debora Liu
deboralh at fel.com.cn
2005-07-29
