Dear Wolfgang, I have updated linux kernel an u-boot from the CVS repository, so I have de latest u-boot and linux version. I grabed the new u-boot an kernel and now hungs later while probing PCI. If I configure linux kernel without PCI support, it boots OK.
I use lite5200b_defconfig configuration. I am missing something in the
configuration relationated with PCI?
U-Boot 1.1.4 (May 12 2006 -
14:45:32)
CPU: MPC5200 v2.2, Core v1.4 at 462
MHz
Bus 132 MHz, IPB 132 MHz, PCI 33
MHz
Board: Freescale
Lite5200B
I2C: 85 kHz,
ready
DRAM: 256
MB
FLASH: 32
MB
*** Warning - bad CRC, using default
environment
PCI: Bus Dev VenId DevId Class
Int
00 1a 1057 5809 0680
00
In:
serial
Out:
serial
Err:
serial
Net: FEC
ETHERNET
IDE: Bus 0:
OK
Device 0: Model: SanDisk SDCFB-32 Firm: HDX 2.15 Ser#:
103407C2604A5824
Type: Hard
Disk
Capacity: 30.6 MB = 0.0 GB (62720 x
512)
Device 1: not
available
Type "run flash_nfs" to mount root filesystem over NFS
Hit any key to stop autoboot: 0
=> bootp 500000 vmlinux.UBoot
BOOTP broadcast 1
Using FEC ETHERNET device
TFTP from server 10.0.7.228; our IP address is 10.0.17.102
Filename 'vmlinux.UBoot'.
Load address: 0x500000
Loading: #################################################################
#################################################################
##########################################################
done
Bytes transferred = 959935 (ea5bf
hex)
=> usb
reset
(Re)start
USB...
USB: scanning bus for devices... 1 USB Device(s)
found
scanning bus for storage devices... 0 Storage Device(s)
found
=> bootm
500000
## Booting image at 00500000
...
Image Name:
Linux-2.4.25
Created: 2006-05-12 12:31:19
UTC
Image Type: PowerPC Linux Kernel Image (gzip
compressed)
Data Size: 959871 Bytes = 937.4
kB
Load Address:
00000000
Entry Point:
00000000
Verifying Checksum ...
OK
Uncompressing Kernel Image ...
OK
Memory BAT mapping: BAT2=256Mb, BAT3=0Mb, residual:
0Mb
Linux version 2.4.25 (igor at ILURI_LINUX) (gcc version 3.3.6) #1 vie may
12 14:27:36 CEST 2006
On node 0 totalpages:
65536
zone(0): 65536
pages.
zone(1): 0
pages.
zone(2): 0
pages.
Kernel command
line:
Calibrating delay loop... 307.20
BogoMIPS
Memory: 256340k available (1636k kernel code, 496k data, 76k init, 0k
highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144
bytes)
Inode cache hash table entries: 16384 (order: 5, 131072
bytes)
Mount cache hash table entries: 512 (order: 0, 4096
bytes)
Buffer cache hash table entries: 16384 (order: 4, 65536
bytes)
Page-cache hash table entries: 65536 (order: 6, 262144
bytes)
POSIX conformance testing by
UNIFIX
PCI: Probing PCI hardware
PCI: moved dev
Wolfgang Denk wrote:
>In message <918EB199DDDFFA42BEA2EB3A1C6021F3CE19E2 at
>correo.fagorautomation.net> you wrote:
>
>
>>We also have a mpc5200liteB evaluation board with u-boot 1.1.4 and linux
>>2.4.25 from Denx. We have realized that when USB is enabled linux
>>doen?t boot, it hungs after u-boot uncompresses linux image.
>>
>>
>
>You need the latest versions of both U-boot and Linux.
>
>For U-Boot, you need a version after April 18 (see especially commit
>ID 8419c013048b1f15f3fa2fc7c0463d860a04ee3e). For the Linux kernel,
>you need a version after April 21 (see especially commit ID
>1ac8b71bdbe6de928ba84c83831f6988a9b51165).
>
>I recommend to grab the top-of-tree from both repositories.
>
>Best regards,
>
>Wolfgang Denk
>
>
>
