Hello
I compile my kernel with
pm82x_deconfig and PCI disabled.
Did I forgot something ??
After error Oops: kernel access of bad area, sig: 11 [#1] the Board
restarts.
Thanks for Helping
Freddy
U-Boot 1.1.4 (May 15 2006 - 09:13:13)
MPC8260 Reset Status: External Soft, External Hard
MPC8260 Clock Configuration
- Bus-to-Core Mult 2.5x, VCO Div 4, 60x Bus Freq 20-60 , Core Freq
50-120
- dfbrg 0, corecnf 0x11, busdf 3, cpmdf 1, plldf 0, pllmf 3, pcidf 3
- vco_out 400000000, scc_clk 100000000, brg_clk 100000000
- cpu_clk 250000000, cpm_clk 200000000, bus_clk 100000000
CPU: MPC8260 (HiP7 Rev 13, Mask 0.1 1K49M) at 250 MHz
Board: PM828
I2C: ready
DRAM: (60x:9COL) 128 MB
FLASH: 32 MB
In: serial
Out: serial
Err: serial
DOC: No DiskOnChip found
Net: FCC1 ETHERNET, FCC2 ETHERNET
BEDBUG:ready
Hit any key to stop autoboot: 0
Using FCC1 ETHERNET device
TFTP from server 192.168.0.1; our IP address is 192.168.0.2
Filename 'uImage-2.6'.
Load address: 0x400000
Loading:
#################################################################
#################################################################
#######################################################
done
Bytes transferred = 945041 (e6b91 hex)
## Booting image at 00400000 ...
Image Name: Linux-2.6.14
Created: 2006-05-30 7:59:00 UTC
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 944977 Bytes = 922.8 kB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Linux version 2.6.14 (root at c3415) (gcc version 4.0.0 (DENX ELDK 4.0
4.0.0)) #1 Tue May 30 09:58:59 CEST 2006
Microsys PM82x PowerPC port
Built 1 zonelists Kernel command line: root=/dev/nfs rw
nfsroot=192.168.0.1:/lop/eldk400/ppc_6xx/ console=ttyCPM1
ip=192.168.0.2:192.168.0.1:192.168.0.1:255.255.255.0:ppc_82xx::off
panic=1
PID hash table entries: 1024 (order: 10, 16384 bytes)
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 127744k available (1556k kernel code, 384k data, 100k init, 0k
highmem)
Mount-cache hash table entries: 512
softlockup thread 0 started up.
NET: Registered protocol family 16
Generic RTC Driver v1.07
Serial: CPM driver $Revision: 0.01 $
ttyCPM0 at MMIO 0xf0011a80 (irq = 4) is a CPM UART
ttyCPM1 at MMIO 0xf0011a90 (irq = 5) is a CPM UART
ttyCPM2 at MMIO 0xf0011a00 (irq = 40) is a CPM UART
ttyCPM3 at MMIO 0xf0011a20 (irq = 41) is a CPM UART
ttyCPM4 at MMIO 0xf0011a40 (irq = 42) is a CPM UART
ttyCPM5 at MMIO 0xf0011a60 (irq = 43) is a CPM UART
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
NFTL driver: nftlcore.c $Revision: 1.97 $, nftlmount.c $Revision: 1.40 $
Oops: kernel access of bad area, sig: 11 [#1]
NIP: C0107A14 LR: C0106660 SP: C036FE30 REGS: c036fd80 TRAP: 0300 Not
tainted
MSR: 00003032 EE: 0 PR: 0 FP: 1 ME: 1 IR/DR: 11
DAR: 00000000, DSISR: 20000000
TASK = c0349ae0[1] 'swapper' THREAD: c036e000 Last syscall: 120
GPR00: C036FE38 C036FE30 C0349AE0 C7CD5EE0 C036FE68 00002AA8 C9002AA8
00AA00AA
GPR08: 00AA00AA C036FE40 00009032 00001032 00AA00AA FFFDFFB7 07FFC000
00000001
GPR16: 00800000 07FFF7BC C0180000 00000000 07FF9484 00000000 07FAE1C0
00000001
GPR24: C036FE58 00000000 C7CD5EE0 C01F0000 C7CD5EE0 C01C4BF4 C036FF18
C036FE68
Call trace: [0000000d] [c0106104] [c010637c] [c01011ec] [c01e1ed4]
[c00039e8] [c0006b84] Kernel panic - not syncing: Attempted to kill
init!
<0>Rebooting in 1 seconds..
