Hi all,
I am using uboot and montavista kernel for our custom MPC8555CDS board.
I enabled the following options in Kernel for kernel Debugging,
CONFIG_BDI_SWITCH=y CONFIG_DEBUG_INFO=y under kernel hacking and MMU XALT in
BDI config file. After uboot initialization I fixed break point at
start_kernel(0xc02784bc), and then I booted the kernel. Without breaking at
start_kernel, it came to login prompt. Please find attached config file with
this mail. Could anybody help me to solve this problem?
Thanks in advance,
Saravanan.S
Bangalore.
BDI Config File
[INIT]
TSZ1 0xFE000000 0xFFFFFFFF ;for flash
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;; TESTING START
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Move the L2SRAM to the initial MMU page
WM32 0xFF720000 0x68010000 ;L2CTL
WM32 0xFF720100 0xFFFC0000 ;L2SRBAR0
WM32 0xFF720000 0xA8010000 ;L2CTL
;
; Clear L2SRAM with DMA
WM32 0xff721110 0x00040000 ;SATR0 SREADTTYPE=Read, don't
snoop
WM32 0xff721114 0xff700004 ;SAR0 Dummy source register
WM32 0xff721118 0x00050000 ;DATR0 DWRITETTTYPE=Write,
snoop local processor
WM32 0xff721120 0x00040000 ;BCR0 Size
WM32 0xff721100 0x0f009404 ;MR0 BWC=f,SAHTS=2(4
bytes),SAHE=1,SWSM=Dest,SRW=1,CTM=1,CS=0
WM32 0xff72111c 0xfffc0000 ;DAR0 which sets CS=1
DELAY 200 ;let DMA complete
WM32 0xff721100 0x00000000 ;MR0 reset condition
; load and execute boot code (needed if STARTUP HALT)
WM32 0xfffffffc 0x48000000 ;loop
EXEC 0xfffffffc 1000
;
; load TLB entries, helper code @ 0xfffff000
WM32 0xfffff000 0x7c0007a4 ;tlbwe
WM32 0xfffff004 0x7c0004ac ;msync
WM32 0xfffff008 0x48000000 ;loop
;
; 1MB TLB1 #1 0x40000000 - 0x400fffff
WSPR 624 0x10010000 ;MAS0:
WSPR 625 0x80000500 ;MAS1:
WSPR 626 0x4000000a ;MAS2:
WSPR 627 0x40000015 ;MAS3:
WSPR 628 0x00000000 ;MAS4:
EXEC 0xfffff000
;
; 64 MB TLB1 #2 0xc0000000 - 0xc3ffffff
WSPR 624 0x10020000 ;MAS0:
WSPR 625 0x80000800 ;MAS1:
WSPR 626 0xc0000008 ;MAS2:
WSPR 627 0xc0000015 ;MAS3:
EXEC 0xfffff000
;
; 64 MB TLB1 #3 0x00000000 - 0x03ffffff
WSPR 624 0x10030000 ;MAS0:
WSPR 625 0x80000800 ;MAS1:
WSPR 626 0x00000008 ;MAS2:
WSPR 627 0x00000015 ;MAS3:
EXEC 0xfffff000
;
; 64 MB TLB1 #4 0x04000000 - 0x07ffffff
WSPR 624 0x10040000 ;MAS0:
WSPR 625 0x80000800 ;MAS1:
WSPR 626 0x04000008 ;MAS2:
WSPR 627 0x04000015 ;MAS3:
EXEC 0xfffff000
;
; 16 MB TLB1 #5 0xff000000 - 0xffffffff
WSPR 624 0x10050000 ;MAS0:
WSPR 625 0x80000700 ;MAS1:
WSPR 626 0xff00000a ;MAS2:
WSPR 627 0xff000015 ;MAS3:
EXEC 0xfffff000
;
; 16 MB TLB1 #0 0xf0000000 - 0xf0ffffff
WSPR 624 0x10000000 ;MAS0:
WSPR 625 0x80000700 ;MAS1:
WSPR 626 0xf0000008 ;MAS2:
WSPR 627 0xf0000015 ;MAS3:
EXEC 0xfffff000
;
; Remove the L2SRAM from the initial MMU page
WM32 0xFF720000 0x28010000 ;L2CTL
;WM32 0xFF720000 0x28000000 ;L2CTL
;;;;;;;;;;;;;;;;;;;;;;;;;; TESTING END
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; move CCSR at 0x40000000
; CCSRBAR
; bit 12 - 23 - BASE_ADDR
WM32 0xFF700000 0x00040000
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; configure local access windows
; LAWBAR0
; bit 12 - 31 = 0x00000000 - base addr
WM32 0x40000c08 0x00000000
; LAWAR0
; bit 1 = 1 - enable window
; bit 8-11 = F - DDR
; bit 26 - 31 = 128MB - size
WM32 0x40000c10 0x80f0001a
; LAWBAR1
; bit 12 - 31 = 0xc0000000 - base addr
WM32 0x40000c28 0x000c0000
; LAWAR1
; bit 1 = 1 - enable window
; bit 8-11 = 4 - local bus
; bit 26 - 31 = 1GB - size
WM32 0x40000c30 0x8040001D
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;Interface enable
WM32 0x400E0070 0xc0000000
;ECM streaming
WM32 0x40001000 0x00000000
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; disable the memory interface with DDR_SDRAM_CFG[MEM_EN]
; DDR_SDRAM_CFG
WM32 0x40002110 0x42008000
; CS0_BNDS
WM32 0x40002000 0x00000007; DDR CS0 now 128MB
; CS0_CONFIG
WM32 0x40002080 0x80800101;0x80800202
; TIMING_CONFIG_1
WM32 0x40002108 0x26241341
; TIMING_CONFIG_2
WM32 0x4000210C 0x00001000
; DDR_SDRAM_MODE
WM32 0x40002118 0x00000062 ;0x00000022 ;old
; DDR_SDRAM_INTERVAL
WM32 0x40002124 0x05200000
; DDR_SDRAM_CLK_CNTL
WM32 0x40002130 0x83000000
DELAY 2000
; DDR_SDRAM_CFG
WM32 0x40002110 0xc2008000 ;0xc2000000 CS_old_value
DELAY 2000
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; configure local bus memory controller
; CS0 - Flash Bank ;0
WM32 0x40005000 0xFe001001 ;BR0 base address at 0xFF800000, port
size 16 bit, GPCM, valid
WM32 0x40005004 0xFe006117 ;OR0 32MB flash size working for flash
;set the PC at the reset address (for debug-->connect)
WREG PC 0xfffffffc ;
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
;;;;;;;;;;;;;;;;;;;;;;;;;; TESTING START
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
; Setup flash programming workspace in L2SRAM disable for now needs to check
;WM32 0x40020000 0x68010000 ;L2CTL
;WM32 0x40020100 0xf0000000 ;L2SRBAR0
;WM32 0x40020000 0xA8010000 ;L2CTL
;WSPR 63 0xf0000000 ;IVPR to workspace
;WSPR 415 0x0001500 ;IVOR15 : Debug exception
;WM32 0xf0001500 0x48000000 ;write valid instruction
;
; Setup flash programming workspace in dual port RAM
;WSPR 63 0x40080000 ;IVPR to workspace
;WSPR 415 0x000007F0 ;IVOR15 : Debug exception
;WM32 0x400807F0 0x48000000 ;write valid instruction
;
; Setup for program execution
WM32 0x40020000 0x28010000 ;L2CTL
WM32 0x40020000 0x28000000 ;L2CTL
WSPR 63 0x00000000 ;IVPR to workspace
WSPR 406 0x0000700 ;IVOR6 : Program exception
WSPR 415 0x0001500 ;IVOR15 : Debug exception
WM32 0x00000700 0x48000000 ;write valid instruction
WM32 0x00001500 0x48000000 ;write valid instruction
;
;;;;;;;;;;;;;;;;;;;;;;;;;; TESTING END
;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
[TARGET]
MMU XLAT ;Added to chech the mmu translation
CPUTYPE 8555 ;the CPU type
JTAGCLOCK 1 ;use 8 MHz JTAG clock
STARTUP RUN ; Start up with loop, halt, run
BREAKMODE HARD ;SOFT or HARD, HARD uses PPC hardware breakpoint
STEPMODE JTAG ;JTAG or HWBP, HWBP uses a hardware breakpoint
WAKEUP 200 ;give reset time to complete
POWERUP 1000 ;start delay after power-up detected in ms
MEMACCESS CORE ;use SAP or CORE for JTAG memory accesses
[HOST]
IP 172.16.4.9
FILE C:\BDI2000\u-boot.bin
FORMAT BIN 0x00080000
LOAD MANUAL ;load code MANUAL or AUTO after reset
PROMPT 8555BBCARD>
[FLASH]
CHIPTYPE STRATAX16
CHIPSIZE 0x2000000 ;The size of one flash chip in bytes
BUSWIDTH 16 SWAP ;The width of the flash memory bus in
bits (8 | 16 | 32)
;WORKSPACE 0x0 ;workspace in RAM
FILE C:\BDI2000\u-boot.bin
FORMAT BIN 0xFFF80000
ERASE 0xFFF80000 ;erase sector 0
[REGS]
FILE C:\BDI2000\reg8560.def
HyperTerminal Boot Messages
=> imi 0x900000
## Checking Image at 00900000 ...
Image Name: Linux-2.6.10_mvl401-8555cds
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1245282 Bytes = 1.2 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
=> bootm 0x900000 0xb00000
## Booting image at 00900000 ...
Image Name: Linux-2.6.10_mvl401-8555cds
Image Type: PowerPC Linux Kernel Image (gzip compressed)
Data Size: 1245282 Bytes = 1.2 M
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
## Current stack ends at 0x03FADD00 => set upper limit to 0x00800000
## cmdline at 0x007FFF00 ... 0x007FFF2C
## Loading RAMDisk Image at 00b00000 ...
Image Name: uImage.ramdisk
Image Type: PowerPC Linux RAMDisk Image (gzip compressed)
Data Size: 2402307 Bytes = 2.3 MB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
## initrd at 0x00B00040 ... 0x00D4
Loading Ramdisk to 03d62000, end 03fac803 ... OK
## Transferring control to Linux (at address 00000000) ...
Memory CAM mapping: CAM0=64Mb, CAM1=0Mb, CAM2=0Mb residual: 0Mb
Linux version 2.6.10_mvl401-8555cds ([EMAIL PROTECTED]) (gcc version 3.4.3 (Mo
ntaVista 3.4.3-25.0.70.0501961 2005-12-17)) #3 Thu Aug 30 18:28:00 IST 2007
CDS Version = 0 in PCI slot 1
Built 1 zonelists
Kernel command line: console=ttyS1,115200 root=/dev/ram rw ip=off
OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fbf76000
PID hash table entries: 512 (order: 9, 8192 bytes)
Warning: real time clock seems stuck!
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 59648k available (1968k kernel code, 700k data, 120k init, 0k highmem)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
spawn_desched_task(00000000)
desched cpu_callback 3/00000000
ksoftirqd started up.
desched cpu_callback 2/00000000
checking if image is initramfs...desched thread 0 s
it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 2346k freed
NET: Registered protocol family 16
PCI: Probing PCI hardware
PCI: Cannot allocate resource region 0 of device 0001:01:00.0
PCI: Cannot allocate resource region 1 of device 0001:01:00.0
PCI: Failed to allocate mem resource #1:[EMAIL PROTECTED] for 0001:01:00.0
JFFS2 version 2.2. (NAND) (C) 2001-2003 Red Hat, Inc.
Generic RTC Driver v1.07
i8042.c: i8042 controller self test timeout.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ s
ttyS0 at MMIO 0xe0004500 (irq = 106) is a 16550A
ttyS1 at MMIO 0xe0004600 (irq = 106) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32768K size 1024 blocksize
loop: loaded (max 8 devices)
eth0: Gianfar Ethernet Controller Version 1.1, 00:e0:0c:00:00:fd
eth0: Running with NAPI enabled
eth0: 256/256 RX/TX BD ring size
eth1: Gianfar Ethernet Controller Version 1.1, 00:e0:0c:00:01:f
eth1: Running with NAPI enabled
eth1: 256/256 RX/TX BD ring size
i2c /dev entries driver
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
elevator: using anticipatory as default io scheduler
physmap flash device: 1000000 at ff000000
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
NET: Registered protocol family 1
NET: Registered protoco
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
Freeing unused kernel memory: 120k init
modprobe: FATAL: Could not load /lib/modules/2.6.10_mvl401-8555cds/modules.dep:
No such file or directory
modprobe: FATAL: Could not load /lib/modules/2.6.10_mvl401-8555cds/modules.dep:
No such file or directory
INIT: version 2.85 booting
0
Mounting a tmpfs over /dev...done.
Creating initial device nodes...done.
0
Mounting local filesystems: mount none on /var/run type tmpfs (rw)
none on /tmp type tmpfs (rw)
Starting hotplug subsystem:
pci
pci [success]
usb
usb [success]
isapnp
isapnp [success]
ide
ide [success]
input
input [success]
scsi
scsi [success]
done.
Starting portmap daemon: portmap/etc/rc.d/rcS.d/S41portmap: 156: nice: not found
INIT: Entering runlevel: 3
Starting internet superserver: inetd.
MontaVista(R) Linux(R) Professional Edition 4.0.1 (0502020)
(none) login:
_______________________________________________
Linuxppc-embedded mailing list
[email protected]
https://ozlabs.org/mailman/listinfo/linuxppc-embedded
