Re: Linux on Virtex board with ARCH=powerpc

Peter Mendham Fri, 27 Jun 2008 08:07:13 -0700

Hi John,

With regard to CONFIG_PPC_UDBG... we have a patch ready that I need to
apply to the Git tree and I'll expedite that.

Great, thanks.

With the console and UART Lite, the only thing I could think of is
making sure you have a dev entry for the UART Lite.

I do.  I used the major and minor numbers from the driver source.

I'm assuming all the boot messages about the console, "enabled", look
the same as the 550 as I have seen that give hints to problems
sometimes.

I'm not really getting anything illuminating. I turned debuggingmessages on and I see the following:

Console: colour dummy device80x25console [ttyUL0]enabled<snip>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharingdisableduartlite: callinguart_register_driver()uartlite: callingof_register_platform_driver()uartlite 800f0000.serial: ulite_of_probe(c7846800,c019713c)ulite console: port=c01aef38;port->mapbase=800f0003800f0000.serial: ttyUL0 at MMIO 0x800f0003 (irq = 0) is auartliteuartlite: calling platform_driver_register()

The only thing that I notice is that the "console [x] enabled" linecomes way before the uartlite driver registers, whereas on the 16550version it's straight afterwards. Does that matter?


Thanks,
-- Peter

Thanks,
John

-----Original Message-----

From: Peter Mendham [mailto:[EMAIL PROTECTED]Sent: Friday, June 27, 2008 6:31 AM

To: John Linn
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: Linux on Virtex board with ARCH=powerpc

Hi John,

Yes, with regard to the non-functional sysace, I was being an idiot: Ihad a small hw problem which now that I have fixed it, the kernel nowreports that my drive is mounted.

I now have a new and rather bizarre problem, which maybe you or someoneelse has met before. I have a simple FPGA design with memory, a sysaceand a uart16550 on an ML405 (I've put my hardware to one side for themoment). It works just fine. If I swap the uart16550 for a uartlite(remaking the kernel with the correct device tree) I see all the bootmessages and the kernel seems to start OK, the root partition is mounted


but then I see nothing from /sbin/init.  This is the same root fs that I

was using with the uart16550 example I just mentioned. So it's a knowngood root fs, but it doesn't appear to be able to output to /dev/console

when I have a uartlite instead of a uart16550. I have selected consolesupport for uartlite. Any ideas?

Incidentally, the uart16550 solution did not work until I removedCONFIG_PPC_UDBG_16550 - the kernel was getting stuck in udbg_550_putcindefinitely.


Thanks,
-- Peter


John Linn wrote:

Hi Peter,

I think you'll get a baseline quicker this way and then you can go on
other less known paths after that.

In my experience, this message happens when there is no compact flash

in

the slot of the board.

I have the system ace device as /dev/xsa2 in my notes, but I have only
used it much. Sorry it's not one of my primary test cases at this

point

in time.

Thanks,
John

-----Original Message-----

From: Peter Mendham [mailto:[EMAIL PROTECTED]Sent: Thursday, June 26, 2008 7:24 AM

To: John Linn
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: Linux on Virtex board with ARCH=powerpc

Hi John,

OK, I've given in and I'm using the xilinx git code now :)  It now

shows

some signs of life, thanks, but the sysace driver is not happy.  My

root

fs is on cf and I'm not using initrd.  The driver loads then gets

stuck,

repeatedly saying:

xsysace 80030000.sysace: kicking stalled fsm; state=2 task=0 iter=1

dc=0

I notice from the driver source that state 2 is the driver attempting

to

acquire the mpu lock.  I have tried the standard xilinx sysace

selftest

code which just acquires and frees the lock (which is fine) so thehardware should be OK (I hope). I have the sysace hooked up to an irq

(the only one), I have no idea whether the dts is correct but it seems

to compare favourably with the ml405 one; mine says (the important
bits):

        intc: [EMAIL PROTECTED] {
            #interrupt-cells = <2>;
            compatible = "xlnx,xps-intc-1.00.a";
            interrupt-controller ;
            reg = < 80010000 10000 >;
            xlnx,num-intr-inputs = <1>;
        } ;
        sysace: [EMAIL PROTECTED] {
            compatible = "xlnx,xps-sysace-1.00.a";
            interrupt-parent = <&intc>;
            interrupts = < 0 2 >;
            reg = < 80030000 10000 >;
            xlnx,family = "virtex4";
            xlnx,mem-width = <10>;
        } ;

Do you have any ideas?

Thanks,
-- Peter

John Linn wrote:

Hi Peter,

To some extent I think you're trying to re-invent the wheel here, but

understand why.

Ideally, you would be able to pull from the mainline kernel to build
this, but Xilinx hasn't got our code into the mainline.  We are

working

on it more proactively now.

So, in the meantime, it would be easier for you to pull from the

Xilinx

git tree as we have solved the problems you are solving I believe.
Git://git.xilinx.com/linux-2.6-xlnx or http://git.xilinx.com/...
We supply the device tree files and kernel configurations for the

ML405

and ML507 boards to help get started.

Thanks and sorry for the inconvenience,
John

-----Original Message-----

From: Peter Mendham [mailto:[EMAIL PROTECTED]Sent: Wednesday, June 25, 2008 10:18 AM

To: John Linn
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: Linux on Virtex board with ARCH=powerpc

OK, this is all new to me, so please bear with me if I've made a

major

mistake.  I ran the kernel until it didn't give me anymore output and

then told xmd to "stop", mrd from any location gave me exactly the

same

32-bit word of garbage.  I then reset the processor and mrd would

give

me what looked like reasonable values.  I found the __log_buf symbol

in

the System.map file (0xc024a108) and tried mrd on what I assume is

the

corresponding physical address of 0x0024a108.  I get the following:

<6>Using Xilinx Virtex machine description
<5>Linux version 2.6.26-rc6 ([EMAIL PROTECTED]) (gcc version 4.2.4) #9

PREEMPT

Wed Jun 25 16:27:33 BST 2008
<7>Entering add_active_range(0, 0, 131072) 0 entries of 256 used
<7>Top of RAM: 0x20000000, Total RAM: 0x20000000
<7>Memory hole size: 0MB
<4>Zone PFN ranges:
<4>  DMA             0 ->   131072
<4>  Normal     131072 ->   131072
<4>Movable zone start PFN for each node
<4>early_node_map[1] active PFN ranges
<4>    0:        0 ->   131072
<7>On node 0 totalpages: 131072
<7>  DMA zone: 1024 pages used for memmap
<7>  DMA zone: 0 pages reserved
<7>  DMA zone: 130048 pages, LIFO batch:31
<7>  Normal zone: 0 pages used for memmap
<7>  Movable zone: 0 pages used for memmap
<4>Built 1 zonelists in Zone order, mobility grouping on.  Total

pages:

130048
<5>Kernel command line: console=ttyUL0 root=/dev/xsa2 rw
<6>Xilinx intc at 0xFDFFF000C025CFFC mapped to 0x0000025d
<4>PID hash table entries: 2048 (order: 11, 8192 bytes)

xmd tells me that the processor stopped at 0xc000fe50, and subsequent

"con" and "stop" sequences do no move this on (it reports the same

each

time). Below is a choice excerpt of my System.map:

c000fdc4 t src_error
c000fddc t dst_error
c000fdf4 T __div64_32
c000fe94 T cacheable_memzero
c000ff38 T memset

So I guess that means it's in __div64_32?

Any ideas?

Thanks in advance,
-- Peter

John Linn wrote:

Sounds like the bootstrap loader has loaded the kernel and passed

off

execution to it, but there's no console working on the kernel.

You can confirm that since you have a probe as you can dump the
__log_buf by getting the address of it using objdump on the elf

image.

It's a pain to convert to readable form, but can help to see that

things

are indeed running. Stop the processor, then do the memory read

command,

mrd, in xmd.

For the console to work with UART Lite, CONFIG_OF must be on in the
kernel configuration, I would check that.

The file, arch/powerpc/boot/virtex.c, has the startup code for the
virtex specific processing.  It checks to make sure there is

compatible

hardware based on the device tree.  If your device tree doesn't

match

that hardware you could have a problem.  I have not found the

powerup

of

the kernel to be very informative if the device tree is wrong.

I pasted in our ML405 device tree below to allow you to compare to

it.

Hope that helps,
John



/*
 * (C) Copyright 2007 Michal Simek
 *
 * Michal SIMEK <[EMAIL PROTECTED]>
 *
 * This program is free software; you can redistribute it and/or
 * modify it under the terms of the GNU General Public License as
 * published by the Free Software Foundation; either version 2 of
 * the License, or (at your option) any later version.
 *

 * This program is distributed in the hope that it will be useful,
 * but WITHOUT ANY WARRANTY; without even the implied warranty of
 * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
 * GNU General Public License for more details.
 *
 * You should have received a copy of the GNU General Public License
 * along with this program; if not, write to the Free Software
 * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
 * MA 02111-1307 USA
 *
 * CAUTION: This file is automatically generated by libgen.
 * Version: Xilinx EDK 10.1.1 EDK_K_SP1.1
 */

/ {
        #address-cells = <1>;
        #size-cells = <1>;
        compatible = "xlnx,virtex";
        model = "testing";
        DDR_SDRAM: [EMAIL PROTECTED] {
                device_type = "memory";
                reg = < 0 8000000 >;
        } ;
        chosen {
                bootargs = "console=ttyS0 ip=on root=/dev/ram";
                linux,stdout-path = "/[EMAIL PROTECTED]/[EMAIL PROTECTED]";
        } ;
        cpus {
                #address-cells = <1>;
                #cpus = <1>;

                #size-cells = <0>;
                ppc405_0: [EMAIL PROTECTED] {
                        clock-frequency = <11e1a300>;
                        compatible = "PowerPC,405", "ibm,ppc405";

                        d-cache-line-size = <20>;
                        d-cache-size = <4000>;
                        device_type = "cpu";
                        i-cache-line-size = <20>;

                        i-cache-size = <4000>;
                        model = "PowerPC,405";
                        reg = <0>;
                        timebase-frequency = <11e1a300>;
                        xlnx,apu-control = <de00>;
                        xlnx,apu-udi-1 = <a18983>;
                        xlnx,apu-udi-2 = <a38983>;
                        xlnx,apu-udi-3 = <a589c3>;
                        xlnx,apu-udi-4 = <a789c3>;
                        xlnx,apu-udi-5 = <a98c03>;
                        xlnx,apu-udi-6 = <ab8c03>;
                        xlnx,apu-udi-7 = <ad8c43>;
                        xlnx,apu-udi-8 = <af8c43>;
                        xlnx,deterministic-mult = <0>;
                        xlnx,disable-operand-forwarding = <1>;
                        xlnx,fastest-plb-clock = "DPLB0";
                        xlnx,generate-plb-timespecs = <1>;
                        xlnx,mmu-enable = <1>;
                        xlnx,pvr-high = <0>;
                        xlnx,pvr-low = <0>;
                } ;
        } ;
        plb: [EMAIL PROTECTED] {
                #address-cells = <1>;
                #size-cells = <1>;
                compatible = "xlnx,plb-v46-1.02.a";
                ranges ;
                IIC_EEPROM: [EMAIL PROTECTED] {
                        compatible = "xlnx,xps-iic-2.00.a";
                        interrupt-parent = <&xps_intc_0>;
                        interrupts = < 4 2 >;
                        reg = < 81600000 10000 >;
                        xlnx,clk-freq = <5f5e100>;
                        xlnx,family = "virtex4";
                        xlnx,gpo-width = <1>;
                        xlnx,iic-freq = <186a0>;
                        xlnx,scl-inertial-delay = <0>;
                        xlnx,sda-inertial-delay = <0>;
                        xlnx,ten-bit-adr = <0>;
                } ;
                LEDs_4Bit: [EMAIL PROTECTED] {
                        compatible = "xlnx,xps-gpio-1.00.a";
                        interrupt-parent = <&xps_intc_0>;
                        interrupts = < 5 2 >;
                        reg = < 81400000 10000 >;
                        xlnx,all-inputs = <0>;
                        xlnx,all-inputs-2 = <0>;
                        xlnx,dout-default = <0>;
                        xlnx,dout-default-2 = <0>;
                        xlnx,family = "virtex4";
                        xlnx,gpio-width = <4>;
                        xlnx,interrupt-present = <1>;
                        xlnx,is-bidir = <1>;
                        xlnx,is-bidir-2 = <1>;
                        xlnx,is-dual = <0>;
                        xlnx,tri-default = <ffffffff>;
                        xlnx,tri-default-2 = <ffffffff>;
                } ;
                RS232_Uart: [EMAIL PROTECTED] {
                        compatible = "ns16550";
                        device_type = "serial";
                        interrupt-parent = <&xps_intc_0>;
                        interrupts = < 6 2 >;
                        reg = < 83e00000 10000 >;
                        reg-offset = <3>;

reg-shift = <2>;clock-frequency = <05f5e100>;

                        xlnx,family = "virtex4";
                        xlnx,has-external-rclk = <0>;
                        xlnx,has-external-xin = <0>;
                        xlnx,is-a-16550 = <1>;
                } ;
                SysACE_CompactFlash: [EMAIL PROTECTED] {
                        compatible = "xlnx,xps-sysace-1.00.a";
                        interrupt-parent = <&xps_intc_0>;
                        interrupts = < 3 2 >;
                        reg = < 83600000 10000 >;
                        xlnx,family = "virtex4";
                        xlnx,mem-width = <10>;
                } ;
                TriMode_MAC_GMII: [EMAIL PROTECTED] {
                        #address-cells = <1>;
                        #size-cells = <1>;
                        compatible = "xlnx,compound";
                        [EMAIL PROTECTED] {
                                compatible = "xlnx,xps-ll-temac-1.01.a";
                                device_type = "network";
                                interrupt-parent = <&xps_intc_0>;
                                interrupts = < 2 2 >;
                                llink-connected = <&PIM2>;
                                local-mac-address = [ 02 00 00 00 00 01
];
                                reg = < 81c00000 40 >;
                                xlnx,bus2core-clk-ratio = <1>;
                                xlnx,phy-type = <1>;
                                xlnx,phyaddr = <1>;
                                xlnx,rxcsum = <0>;
                                xlnx,rxfifo = <1000>;
                                xlnx,temac-type = <1>;
                                xlnx,txcsum = <0>;
                                xlnx,txfifo = <1000>;
                        } ;
                } ;
                [EMAIL PROTECTED] {
                        #address-cells = <1>;
                        #size-cells = <1>;
                        compatible = "xlnx,mpmc-4.00.a";
                        PIM2: [EMAIL PROTECTED] {
                                compatible = "xlnx,ll-dma-1.00.a";
                                interrupt-parent = <&xps_intc_0>;
                                interrupts = < 1 2 0 2 >;
                                reg = < 84600100 80 >;
                        } ;
                } ;
                xps_bram_if_cntlr_1: [EMAIL PROTECTED] {
                        compatible = "xlnx,xps-bram-if-cntlr-1.00.a";
                        reg = < ffffe000 2000 >;
                        xlnx,family = "virtex4";
                } ;
                xps_intc_0: [EMAIL PROTECTED] {
                        #interrupt-cells = <2>;
                        compatible = "xlnx,xps-intc-1.00.a";
                        interrupt-controller ;
                        reg = < 81800000 10000 >;
                        xlnx,num-intr-inputs = <7>;
                } ;
        } ;
        ppc405_0_dplb1: [EMAIL PROTECTED] {
                #address-cells = <1>;
                #size-cells = <1>;
                compatible = "xlnx,plb-v46-1.02.a";
                ranges ;
        } ;
}  ;





-----Original Message-----

From: Peter Mendham [mailto:[EMAIL PROTECTED]Sent: Tuesday, June 24, 2008 1:21 PM

To: John Linn
Cc: linuxppc-embedded@ozlabs.org
Subject: Re: Linux on Virtex board with ARCH=powerpc

Hi John,

Thanks for your reply, that's really helpful.  I'm actually using

the

mainline kernel, rather than the one from the xilinx git tree, but
your
information has really moved me on. My first problem was that theXilinx utility (from the git tree) for device tree dts generation
didn't
insert a "linux,stdout-path" node under "chosen".  I spotted that

the

ml403 example had this, so after adding it I got early consolemessages. Everything now grinds to a halt after I get the message
"flat
tree at 0x40ad60" which is just before it calls the kernel, so I
assume
it's that call that is killing it. I have "console=ttyUL0" for myuartlite, so I should be getting messages, shouldn't I? Do you know

where the next execution point is?  Maybe I could find out where

it's

getting stuck.

I haven't managed to generate an ACE file, I'm just loading the

kernel

image from xmd ATM, genace won't play ball for me, it complains

about

-board user not being valid, it won't even run on the examples

copied

directly from the user manual.  Anyway, I think genace is a bit OT,

and

I can manage with xmd for now.

Thanks,
-- Peter

John Linn wrote:

Hi Peter,

I'm not up on what can be done with the simple image you refer to

in

1.

I'm sure I should be, but there's a lot to learn.

With regards to 2, the elf image, zImage (without the elf

extension),

is

located in arch/powerpc/boot.

You can make a SystemACE file from that elf image just as you did

in

arch/ppc.  We have a default device tree file, ml405.dts, in the
arch/powerpc/boot/dts directory for our ml405 board. The kernel
configuration has a config, DEVICE_TREE, that specifies the name of

the

device tree file. I normally compile the device tree into the

kernel

which is the default build, make ARCH=powerpc zImage. That image

does

not require a boot loader.

I inserted the text below from a document that I have about

building

the

arch/ppc and arch/powerpc kernels.

Hope that helps,
John


Notation

The phrase "<ppc or powerpc>" is used throughput the text and means

that

one or the other, "ppc" or "powerpc" is to be typed depending on

the

architecture you are building.

Commands that are used in a bash shell are preceded by ">".

Getting Ready To Build the Kernel

This assumes you installed the ELDK tools and assumes you'll be

using

bash shell.

bash
export CROSS_COMPILE=ppc_4xx-

Setting Up the Kernel Tree

If you have previously built this kernel for another architecture,

ppc

or powerpc, then the tree needs to be setup correctly for the new
architecture.  Assuming you have not previously built it, this does

not

need to be done.

make ARCH=<ppc or powerpc> mrproper

Configuring the Kernel

The kernel should be configured to run on the ML405 or ML507 board

from

Xilinx.

make ARCH=<ppc or powerpc>  ml405_defconfig

or

make ARCH=<ppc or powerpc> ml507_defconfig

Building the Kernel

The following command will build the Linux kernel assuming you are

in

the root directory of the kernel.  The root directory of the kernel

from

the Xilinx Git tree is linux-2.6-xlnx. An elf file, zImage.elf, is
created in the arch/ppc/boot/images directory for ppc architecture.

An

elf file, zImage, is created in the the arch/powerpc/boot directory

for

the powerpc architecture.

make ARCH=<ppc or powerpc> zImage

        
Building the Kernel With Ramdisk

A ram disk image, a file named *.gz, must be placed into the
arch/ppc/boot/images or arch/powerpc/boot directory, depending on

the

architecture, prior to building the kernel.

make ARCH=<ppc or powerpc> zImage.initrd

An elf file, zImage.initrd.elf, is created in arch/ppc/boot/images
directory for the ppc architecture. An elf file file,

zImage.initrd,

is

created in arch/powerpc/boot directory for the powerpc

architecture.

Generating An Ace File

The elf file generated for the kernel and the bit stream can be

combined

to create an ACE file for compact flash.  The following assumes a

bash

shell where XMD is accessible and a xilinx probe attached to the

board

for which you are generating an ace file.

xmd -tcl genace.tcl -jprog -target ppc_hw -hw <bit file name> -elf

<elf

file name> -board <ml405 or ml507> -ace <desired ace file name>

-----Original Message-----
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED]

On

Behalf Of Peter Mendham
Sent: Tuesday, June 24, 2008 3:02 AM
To: linuxppc-embedded@ozlabs.org
Subject: Linux on Virtex board with ARCH=powerpc

Dear all,

I'm trying to boot a 2.6.26-rc6 kernel on a custom Virtex 4 board.

have used the Xilinx utility to generate a device tree and now want

to

generate an image for throwing onto CF for use with a SystemACE

(just

like on the the ML3/4xx boards).  I don't want to use a bootloader

(I

don't really need one).  I saw something on this list about
simpleImage,
"simple" sounded good to me so I thought I'd try that (or did Imisinterpret what this is for?). I also don't want the image to be
too
big, I always used to use a zImage under ARCH=ppc. So, two

questions,

which hopefully are easy ones:
1. I did what Grant said in a post to this list about simpleImage,
and
dumped my dts into arch/powerpc/boot/dts and I called it system.dts
(for
now). I then tried to do make simpleImage.system which ran rightthrough to final link then moaned about a missing

simpleboot-system.

Where is this supposed to come from?  What am I doing wrong?  I

naively

tried copying simpleboot.o to simpleboot-system.o and the error

went

away.  Hmm.
2. I need an ELF to give to my SystemACE file generator.  This used

to

pop up in arch/ppc/boot/images and be called zImage.elf, which made

sense to me.  What's the deal now with powerpc?  What should I be

using?

Finally, can anyone give me a heads-up on any gotchas with what I'm

trying to do.  As you can tell, I don't entirely know what I'm

doing,

so

any pointers would be gratefully received.

Thanks,
-- Peter


The University of Dundee is a Scottish Registered Charity, No.

SC015096.

_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded


This email and any attachments are intended for the sole use of the

named recipient(s) and contain(s) confidential information that may

be

proprietary, privileged or copyrighted under applicable law. If you

are

not the intended recipient, do not read, copy, or forward this email
message or any attachments. Delete this email message and any
attachments immediately.

The University of Dundee is a Scottish Registered Charity, No.

SC015096.

This email and any attachments are intended for the sole use of the

named recipient(s) and contain(s) confidential information that may

be

proprietary, privileged or copyrighted under applicable law. If you

are

not the intended recipient, do not read, copy, or forward this email
message or any attachments. Delete this email message and any
attachments immediately.

The University of Dundee is a Scottish Registered Charity, No.

SC015096.

This email and any attachments are intended for the sole use of the

named recipient(s) and contain(s) confidential information that may be
proprietary, privileged or copyrighted under applicable law. If you

are

not the intended recipient, do not read, copy, or forward this email
message or any attachments. Delete this email message and any
attachments immediately.

The University of Dundee is a Scottish Registered Charity, No.

SC015096.



This email and any attachments are intended for the sole use of the

named recipient(s) and contain(s) confidential information that may be
proprietary, privileged or copyrighted under applicable law. If you are
not the intended recipient, do not read, copy, or forward this email
message or any attachments. Delete this email message and any
attachments immediately.



The University of Dundee is a Scottish Registered Charity, No. SC015096.




This email and any attachments are intended for the sole use of the named 
recipient(s) and contain(s) confidential information that may be proprietary, 
privileged or copyrighted under applicable law. If you are not the intended 
recipient, do not read, copy, or forward this email message or any attachments. 
Delete this email message and any attachments immediately.



The University of Dundee is a Scottish Registered Charity, No. SC015096.


_______________________________________________
Linuxppc-embedded mailing list
Linuxppc-embedded@ozlabs.org
https://ozlabs.org/mailman/listinfo/linuxppc-embedded

Re: Linux on Virtex board with ARCH=powerpc

Reply via email to