This is an automatic generated email to let you know that the following patch were queued at the http://git.linuxtv.org/cgit.cgi/v4l-utils.git tree:
Subject: rds-ctl: improve usage messages Author: Hans Verkuil <hans.verk...@cisco.com> Date: Wed Feb 28 21:45:07 2018 +0100 Drop the '=' separator between the option and the arguments in the usage message. It's confusing and not needed. Signed-off-by: Hans Verkuil <hans.verk...@cisco.com> utils/rds-ctl/rds-ctl.cpp | 12 ++++++------ 1 file changed, 6 insertions(+), 6 deletions(-) --- http://git.linuxtv.org/cgit.cgi/v4l-utils.git/commit/?id=633d4bc936090ab92549e316510a73582f93457b diff --git a/utils/rds-ctl/rds-ctl.cpp b/utils/rds-ctl/rds-ctl.cpp index 272c8d75833e..05b882e3fee5 100644 --- a/utils/rds-ctl/rds-ctl.cpp +++ b/utils/rds-ctl/rds-ctl.cpp @@ -115,7 +115,7 @@ static void usage_common(void) printf("\nGeneral/Common options:\n" " --all display all device information available\n" " -D, --info show driver info [VIDIOC_QUERYCAP]\n" - " -d, --device=<dev> use device <dev>\n" + " -d, --device <dev> use device <dev>\n" " If <dev> starts with a digit, then /dev/radio<dev> is used\n" " default: checks for RDS-capable devices,\n" " uses device with lowest ID\n" @@ -128,11 +128,11 @@ static void usage_tuner(void) { printf("\nTuner/Modulator options:\n" " -F, --get-freq query the frequency [VIDIOC_G_FREQUENCY]\n" - " -f, --set-freq=<freq>\n" + " -f, --set-freq <freq>\n" " set the frequency to <freq> MHz [VIDIOC_S_FREQUENCY]\n" " -T, --get-tuner query the tuner settings [VIDIOC_G_TUNER]\n" - " --tuner-index=<idx> Use idx as tuner idx for tuner/modulator commands\n" - " --freq-seek=dir=<0/1>,wrap=<0/1>,spacing=<hz>\n" + " --tuner-index <idx> Use idx as tuner idx for tuner/modulator commands\n" + " --freq-seek dir=<0/1>,wrap=<0/1>,spacing=<hz>\n" " perform a hardware frequency seek [VIDIOC_S_HW_FREQ_SEEK]\n" " dir is 0 (seek downward) or 1 (seek upward)\n" " wrap is 0 (do not wrap around) or 1 (wrap around)\n" @@ -147,9 +147,9 @@ static void usage_rds(void) printf("\nRDS options: \n" " -b, --rbds parse the RDS data according to the RBDS standard\n" " -R, --read-rds enable reading of RDS data from device\n" - " --file=<path> open a RDS stream file dump instead of a device\n" + " --file <path> open a RDS stream file dump instead of a device\n" " all General and Tuner Options are disabled in this mode\n" - " --wait-limit=<ms> defines the maximum wait duration for avaibility of new\n" + " --wait-limit <ms> defines the maximum wait duration for avaibility of new\n" " RDS data\n" " <default>: 5000 ms\n" " --print-block prints all valid RDS fields, whenever a value is updated\n" _______________________________________________ linuxtv-commits mailing list linuxtv-commits@linuxtv.org https://www.linuxtv.org/cgi-bin/mailman/listinfo/linuxtv-commits
