On Tue Oct 14 14:55:09 2025 -0400, Frank Li wrote:
> Convert ti,tvp5150.txt to yaml format.
>
> Signed-off-by: Frank Li <[email protected]>
> Reviewed-by: Rob Herring (Arm) <[email protected]>
> Reviewed-by: David Heidelberg <[email protected]>
> [Sakari Ailus: Align the endpoint properties to the right column.]
> Signed-off-by: Sakari Ailus <[email protected]>
> Signed-off-by: Hans Verkuil <[email protected]>
Patch committed.
Thanks,
Hans Verkuil
.../devicetree/bindings/media/i2c/ti,tvp5150.txt | 157 ---------------------
.../devicetree/bindings/media/i2c/ti,tvp5150.yaml | 133 +++++++++++++++++
2 files changed, 133 insertions(+), 157 deletions(-)
---
diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
deleted file mode 100644
index 94b908ace53c..000000000000
--- a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.txt
+++ /dev/null
@@ -1,157 +0,0 @@
-* Texas Instruments TVP5150 and TVP5151 video decoders
-
-The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
-(and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
-with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
-
-Required Properties:
-====================
-- compatible: Value must be "ti,tvp5150".
-- reg: I2C slave address.
-
-Optional Properties:
-====================
-- pdn-gpios: Phandle for the GPIO connected to the PDN pin, if any.
-- reset-gpios: Phandle for the GPIO connected to the RESETB pin, if any.
-
-The device node must contain one 'port' child node per device physical input
-and output port, in accordance with the video interface bindings defined in
-Documentation/devicetree/bindings/media/video-interfaces.txt. The port nodes
-are numbered as follows
-
- Name Type Port
- --------------------------------------
- AIP1A sink 0
- AIP1B sink 1
- Y-OUT src 2
-
-The device node must contain at least one sink port and the src port. Each
input
-port must be linked to an endpoint defined in [1]. The port/connector layout is
-as follows
-
-tvp-5150 port@0 (AIP1A)
- endpoint@0 -----------> Comp0-Con port
- endpoint@1 ------+----> Svideo-Con port
-tvp-5150 port@1 (AIP1B) |
- endpoint@1 ------+
- endpoint@0 -----------> Comp1-Con port
-tvp-5150 port@2
- endpoint (video bitstream output at YOUT[0-7] parallel bus)
-
-Required Endpoint Properties for parallel synchronization on output port:
-=========================================================================
-
-- hsync-active: Active state of the HSYNC signal. Must be <1>
(HIGH).
-- vsync-active: Active state of the VSYNC signal. Must be <1>
(HIGH).
-- field-even-active: Field signal level during the even field data
- transmission. Must be <0>.
-
-Note: Do not specify any of these properties if you want to use the embedded
- BT.656 synchronization.
-
-Optional Connector Properties:
-==============================
-
-- sdtv-standards: Set the possible signals to which the hardware tries to lock
- instead of using the autodetection mechanism. Please look at
- [1] for more information.
-
-[1]
Documentation/devicetree/bindings/display/connector/analog-tv-connector.yaml.
-
-Example - three input sources:
-#include <dt-bindings/display/sdtv-standards.h>
-
-comp_connector_0 {
- compatible = "composite-video-connector";
- label = "Composite0";
- sdtv-standards = <SDTV_STD_PAL_M>; /* limit to pal-m signals */
-
- port {
- composite0_to_tvp5150: endpoint {
- remote-endpoint = <&tvp5150_to_composite0>;
- };
- };
-};
-
-comp_connector_1 {
- compatible = "composite-video-connector";
- label = "Composite1";
- sdtv-standards = <SDTV_STD_NTSC_M>; /* limit to ntsc-m signals */
-
- port {
- composite1_to_tvp5150: endpoint {
- remote-endpoint = <&tvp5150_to_composite1>;
- };
- };
-};
-
-svideo_connector {
- compatible = "svideo-connector";
- label = "S-Video";
-
- port {
- #address-cells = <1>;
- #size-cells = <0>;
-
- svideo_luma_to_tvp5150: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&tvp5150_to_svideo_luma>;
- };
-
- svideo_chroma_to_tvp5150: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&tvp5150_to_svideo_chroma>;
- };
- };
-};
-
-&i2c2 {
- tvp5150@5c {
- compatible = "ti,tvp5150";
- reg = <0x5c>;
- pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
- reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- port@0 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <0>;
-
- tvp5150_to_composite0: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&composite0_to_tvp5150>;
- };
-
- tvp5150_to_svideo_luma: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&svideo_luma_to_tvp5150>;
- };
- };
-
- port@1 {
- #address-cells = <1>;
- #size-cells = <0>;
- reg = <1>;
-
- tvp5150_to_composite1: endpoint@0 {
- reg = <0>;
- remote-endpoint = <&composite1_to_tvp5150>;
- };
-
- tvp5150_to_svideo_chroma: endpoint@1 {
- reg = <1>;
- remote-endpoint = <&svideo_chroma_to_tvp5150>;
- };
- };
-
- port@2 {
- reg = <2>;
-
- tvp5150_1: endpoint {
- remote-endpoint = <&ccdc_ep>;
- };
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
new file mode 100644
index 000000000000..382a29652a05
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/i2c/ti,tvp5150.yaml
@@ -0,0 +1,133 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/i2c/ti,tvp5150.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Texas Instruments TVP5150 and TVP5151 video decoders
+
+maintainers:
+ - Frank Li <[email protected]>
+
+description:
+ The TVP5150 and TVP5151 are video decoders that convert baseband NTSC and PAL
+ (and also SECAM in the TVP5151 case) video signals to either 8-bit 4:2:2 YUV
+ with discrete syncs or 8-bit ITU-R BT.656 with embedded syncs output formats.
+
+properties:
+ compatible:
+ const: ti,tvp5150
+
+ reg:
+ maxItems: 1
+
+ pdn-gpios:
+ maxItems: 1
+
+ reset-gpios:
+ maxItems: 1
+
+ '#address-cells':
+ const: 1
+
+ '#size-cells':
+ const: 0
+
+ port@0:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ sink port node, AIP1A
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ port@1:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ sink port node, AIP1B
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ port@2:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description:
+ source port node, Y-OUT
+
+ properties:
+ endpoint:
+ $ref: /schemas/media/video-interfaces.yaml#
+ unevaluatedProperties: false
+
+required:
+ - compatible
+ - reg
+ - port@2
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/display/sdtv-standards.h>
+ #include <dt-bindings/gpio/gpio.h>
+
+ i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ bridge@5c {
+ compatible = "ti,tvp5150";
+ reg = <0x5c>;
+ pdn-gpios = <&gpio4 30 GPIO_ACTIVE_LOW>;
+ reset-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0>;
+
+ endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&composite0_to_tvp5150>;
+ };
+
+ endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&svideo_luma_to_tvp5150>;
+ };
+ };
+
+ port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&composite1_to_tvp5150>;
+ };
+
+ endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&svideo_chroma_to_tvp5150>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ endpoint {
+ remote-endpoint = <&ccdc_ep>;
+ };
+ };
+ };
+ };
_______________________________________________
linuxtv-commits mailing list -- [email protected]
To unsubscribe send an email to [email protected]
