Hi, thanks for the reply ! On Wednesday 30 May 2007 17:34:37 [EMAIL PROTECTED] wrote: > To see if tc1000ts is really doing its job, you can change > id:5:initdefault to id:3:initdefault in your /etc/inittab. This > enables your system to start without launching X server. > > Restart your system, then run tc1000ts and /bin/setserial /dev/ttyS2 > autoconfig from the console. If setserial returns with valid info, > start X server by startx. Otherwise, you may need to add debug > statement to tc1000ts.c to see what's going on. > > Ping
I already tried in runlevel 3 before, exactly the same results as in 5: # <login as root straight after booting> # /bin/setserial /dev/ttyS2 < /dev/ttyS2, UART: unknown, Port 0x03e(, IRQ: 4 # /usr/sbin/tc1000ts # /bin/setserial /dev/ttyS2 < /dev/ttyS2, UART: unknown, Port 0x03e(, IRQ: 4 # /bin/setserial /dev/ttyS2 autoconfig < /dev/ttyS2, UART: unknown, Port 0x03e(, IRQ: 4 # /bin/setserial /dev/ttyS2 < /dev/ttyS2, UART: unknown, Port 0x03e(, IRQ: 4 [ . . . ] I'd love to have a try with the debug output. However since not having a clue I don't know what to output how ! Maybe you could give me some help here ? I'd say this is what I have to re-check: 1.) are the two addresses declared at the beginning of tc1000ts.c correct for a TC1000? How do I tell or check ? --- const int cfgindex = 0x4e; const int cfgdata = 0x4f; --- I understand the "wsio" macro defined below and as far as i recall "outb" itself is a kernel macro to output a byte to a port, whatever a port means here, I'd guess a register address to be written to? 2.) that would mean that the following 9 usages of the "wsio" macro write values to the registers, probably to program the underlying i/o chip? So, how do I tell if these are are right sequences ? Probably hardware dependend, so in addition how to I find out the type of hardware ? Guess I have to wait for a few hints from you... Thanks, arkascha > > On 5/28/07, Christian Reiner <[EMAIL PROTECTED]> wrote: > > Hi, > > I spent quite a while trying to find out how to get the tablet stuff > > working on a Compaq TC1000. Amongst other stuff I came about the > > linuxwacom site and found the Documentation about Tablet PCs promising. > > > > I have the impression that I am stuck at initializing the serial device > > (connecting the tablet hardware to it). As mentioned in the > > documentation, chapter 7, this has to be initialized on some Compaq > > Tablet PCs. There is a small c application meant to do this, but it is > > written for a compaq TC1100, a slightly newer model. It is also mentioned > > that this application has not been tested with the TC1000. I would like > > to do that, but I have no idea about kernel hacking and hardware stuff. > > So maybe someone can give me a helping hand? > > > > Thanks for any reply, I'll be happy to provide additional info ! > > arkascha > > > > > > > > > > This is the setup so far: > > Distribution: opensuse-10.2 > > > > I have the tc1000ts.c file compiled with -O2 and call it > > from /etc/init.d/boot.local: > > > > # some comments > > touch /var/lock/subsys/local > > /usr/sbin/tc1000ts > > /bin/setserial /dev/ttyS2 autoconfig > > > > boot.local IS processed, I can generate errors or logging from it. > > > > Nevertheless a setserial call afterwards still gives: > > # setserial /dev/ttyS2 > > /dev/ttyS2, UART: unknown, Port: 0x03e8, IRQ: 4 > > > > Consequently wacdump does not work: > > # wacdump /dev/ttyS2 > > WacomOpenTablet: Invallid argument > > I also tried to use setserial by hand (without autofconfig), but could > > not produce any result. > > > > Some lines from my xorg.conf: > > > > . . . > > Section "InputDevice" > > Driver "mouse" > > Identifier "Mouse[1]" > > Option "Buttons" "5" > > Option "Device" "/dev/input/mice" > > Option "Name" "Jing-Mold Enterprise USB K/B+Mouse" > > Option "Protocol" "explorerps/2" > > Option "Vendor" "Sysp" > > Option "ZAxisMapping" "4 5" > > EndSection > > > > Section "InputDevice" > > Driver "wacom" > > Identifier "Mouse[3]" > > Option "Device" "/dev/ttyS2" > > Option "ForceDevice" "ISDV4" > > Option "InputFashion" "Tablet" > > Option "Mode" "Absolute" > > Option "Name" "ISDV4 TABLET PC (SERIAL)" > > Option "SendCoreEvents" "on" > > Option "Type" "stylus" > > Option "Vendor" "WACOM" > > EndSection > > > > Section "InputDevice" > > Driver "wacom" > > Identifier "Mouse[5]" > > Option "Device" "/dev/ttyS2" > > Option "ForceDevice" "ISDV4" > > Option "InputFashion" "Cursor" > > Option "Mode" "Absolute" > > Option "Name" "ISDV4 TABLET PC Stylus (SERIAL)" > > Option "Protocol" "Auto" > > Option "Type" "cursor" > > Option "Vendor" "WACOM" > > EndSection > > . . . > > > > ------------------------------------------------------------------------- > > This SF.net email is sponsored by DB2 Express > > Download DB2 Express C - the FREE version of DB2 express and take > > control of your XML. No limits. Just data. Click to get it now. > > http://sourceforge.net/powerbar/db2/ > > _______________________________________________ > > Linuxwacom-discuss mailing list > > Linuxwacom-discuss@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/linuxwacom-discuss ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ Linuxwacom-discuss mailing list Linuxwacom-discuss@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/linuxwacom-discuss
