This is a long shot, but is the IP address on the 2nd NIC "lower" than the IP on the 1st NIC? Example 10.10.10.10 vs 192.168.1.10 (10.x.x.x is "lower" than 192.x.x.x)
If so it *could* be related to SkipAsSource and you may be able to disable the 2nd NIC as a Source. See http://blogs.technet.com/b/heyscriptingguy/archive/2013/01/24/use-powershell-to-change-ip-behavior-with-skipassource.aspx and http://blogs.catapultsystems.com/chsimmons/archive/2014/11/05/sccm-inventory-of-nic-skipassource/ Chad Simmons | Microsoft System Center Configuration Manager Consultant | linkedin.com/in/chadsimmons From: [email protected] [mailto:[email protected]] On Behalf Of Nick Sent: Tuesday, September 29, 2015 2:16 PM To: [email protected] Subject: RE: [mssms] RE: SCCM 2007 Client with Multiple Network Adapters - Any way to tell SCCM to use a specific adapter for communications? Change your boundary so both adapters IPs fall into the preferred site? From: [email protected] <mailto:[email protected]> [mailto:[email protected]] On Behalf Of Edward Woo Sent: Tuesday, September 29, 2015 2:57 PM To: [email protected] <mailto:[email protected]> Subject: [mssms] RE: SCCM 2007 Client with Multiple Network Adapters - Any way to tell SCCM to use a specific adapter for communications? I checked with our desktop support team and they mentioned that the desired adapter was already at the top of the list and that didn’t work. From: [email protected] <mailto:[email protected]> [mailto:[email protected]] On Behalf Of Raghav, Abhishek Sent: Monday, September 28, 2015 11:54 PM To: [email protected] <mailto:[email protected]> Subject: [mssms] RE: SCCM 2007 Client with Multiple Network Adapters - Any way to tell SCCM to use a specific adapter for communications? Adapter and binding setting should help. Control Panel\Network and Internet\Network Connections\Advance\Advance Settings Change the adapter order and move the one you want to use on top. From: [email protected] <mailto:[email protected]> [mailto:[email protected]] On Behalf Of Edward Woo Sent: Tuesday, September 29, 2015 6:38 AM To: [email protected] <mailto:[email protected]> Subject: [mssms] SCCM 2007 Client with Multiple Network Adapters - Any way to tell SCCM to use a specific adapter for communications? Hi All, I have a workstation with two network adapters installed on it that I’m trying to get working with SCCM 2007. The primary IP address falls under the site boundaries of the desired Primary Site server. The IP address of the 2nd network adapter is connected to an external hardware that we have no control over its setting, but unfortunately happens to fall into the site boundaries of a different Primary Site server. I can see that some communications is going to the correct Primary Site server, but when the system is trying to download software packages to run advertisements targeted against it, the logs show that it is trying to access the other primary site server, which fails. I am unable to change the IP address of the 2nd network adapter to something else. Is there a way to configure the OS or SCCM to ignore that adapter and focus the communications on one specific network adapter? Thanks, Edward Woo This message may contain information that is confidential or privileged. If you are not the intended recipient, please advise the sender immediately and delete this message. See http://www.blackrock.com/corporate/en-us/compliance/email-disclaimers for further information. Please refer to http://www.blackrock.com/corporate/en-us/compliance/privacy-policy for more information about BlackRock’s Privacy Policy. BlackRock is a trading name of BlackRock (Singapore) Limited. For a list of BlackRock's office addresses worldwide, see http://www.blackrock.com/corporate/en-us/about-us/contacts-locations. © 2015 BlackRock, Inc. All rights reserved.
