I updated to the latest code and I'm still seeing the same behavior. That is, thread_plan_sp->RestoreThreadState() is being called, and it does restore the stop info for the thread to the old stop info, but when Thread::SetupForResume() calls Thread::GetStopInfo() that function creates stop info based on the completed thread plan stack rather than using m_actual_stop_info_sp.
Any suggestions? I'd be curious to know why this doesn't happen on Mac OS X because it looks like it would. -Andy -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Kaylor, Andrew Sent: Wednesday, December 05, 2012 4:38 PM To: Jim Ingham Cc: [email protected] Subject: Re: [lldb-dev] Continue misfiring after expression evaluation Hi Jim, I am working with an old version of the code, so things were in a bit different state for me. I was seeing Thread::RestoreThreadStateFromCheckpoint() being called. The problem is that when Thread::SetupForResume() calls Thread::GetStopInfo(), the latter does this: ThreadPlanSP plan_sp (GetCompletedPlan()); if (plan_sp && plan_sp->PlanSucceeded()) return StopInfo::CreateStopReasonWithPlan (plan_sp, GetReturnValueObject()); else { ProcessSP process_sp (GetProcess()); if (process_sp && m_actual_stop_info_sp && m_actual_stop_info_sp->IsValid() && m_thread_stop_reason_stop_id == process_sp->GetStopID()) return m_actual_stop_info_sp; else return GetPrivateStopReason (); } Since the completed stop plan from the expression command is still around, the stop info comes from there. The thread's m_actual_stop_info seems to be correct, but the code doesn't get to the point where it would use it. I'll update to the latest code and see if this is still happening, but I wanted to tell you what I knew while I was still in a known state. I'll let you know what happens with the new code. -Andy -----Original Message----- From: Jim Ingham [mailto:[email protected]] Sent: Wednesday, December 05, 2012 3:50 PM To: Kaylor, Andrew Cc: [email protected] Subject: Re: [lldb-dev] Continue misfiring after expression evaluation I don't see this happening on Mac OS X. That test succeeds, and I don't see the behavior you describe. You should not need to clear the completed plan stack. The way it is supposed to work is as follows: Running functions is always done by Process::RunThreadPlan. After the ThreadPlanCallFunction gets done running in that function, we do this bit of code: // Restore the thread state if we are going to discard the plan execution. if (return_value == eExecutionCompleted || discard_on_error) { thread_plan_sp->RestoreThreadState(); } That should set the StopInfo that was squirreled away in Thread::CheckpointThreadState back as the current StopInfo for the thread. Is that getting called? If not, why not? If it is getting called, why isn't it succeeding in resetting the thread's StopInfo back to the old reason? Note, up till a couple of weeks ago this work was done in the DoTakedown method of ThreadPlanCallFunction, but I moved resetting the StopInfo out of that function (which gets called while the stop event for the function call is still being processed) to here, because otherwise it might trigger the original StopInfo's PerformAction while you are in the middle of handing the ThreadPlanCallFunction's execution, which isn't right. Hope that helps. Jim On Dec 5, 2012, at 3:28 PM, "Kaylor, Andrew" <[email protected]> wrote: > Hi all, > > I've been debugging a problem on Linux where if you hit a breakpoint, then > evaluate an expression that requires JITing, then continue LLDB will break at > the line you were already on. I don't know if this problem is specific to > Linux, but that's where I'm debugging it. This problem appears in the > 'lang/c/setvalues/TestSetValues.py' test case, but can also be reproduced > manually. > > What I'm seeing is that when the 'continue' handling calls > Thread::SetupForResume() the current Thread reports its stop reason as > 'eStopReasonPlanComplete' because the ThreadPlan for evaluating the > expression is still on the completed plans stack. As a result, the > ThreadPlanStepOverBreakpoint plan doesn't get queued. If I add calls to > 'm_completed_plan_stack.clear()' and 'm_discarded_plan_stack.clear()' at the > top of the 'if (GetResumeState() == eStateSuspended)' block in > Thread::SetupForResume() then everything works as expected. > > Obviously, that feels like a pretty risky thing to do, at best. It seems > like the expression command handling should have done something to clear the > completed plan stack when it was finished, but as of yet I haven't found a > place where that is appropriate. > > Can anyone give me guidance on this issue? > > Thanks, > Andy > _______________________________________________ > lldb-dev mailing list > [email protected] > http://lists.cs.uiuc.edu/mailman/listinfo/lldb-dev _______________________________________________ lldb-dev mailing list [email protected] http://lists.cs.uiuc.edu/mailman/listinfo/lldb-dev _______________________________________________ lldb-dev mailing list [email protected] http://lists.cs.uiuc.edu/mailman/listinfo/lldb-dev
