Copying this to the odp-dpdk mailing list, which is where the discussion should reside.
On Tue, Oct 11, 2016 at 10:28 AM, Maxim Uvarov <[email protected]> wrote: > Try to clone it by name, not by IP address: > git clone git://dpdk.org/dpdk > > Get this link from here: > http://dpdk.org/dev > > and please be free to provide link correction patch. > > > Maxim. > > > > > On 11 October 2016 at 16:51, Elo, Matias (Nokia - FI/Espoo) < > [email protected]> wrote: > > > > -----Original Message----- > > > From: lng-odp [mailto:[email protected]] On Behalf Of > > Francois > > > Ozog > > > Sent: Tuesday, October 11, 2016 4:23 PM > > > To: LNG ODP Mailman List <[email protected]> > > > Subject: [lng-odp] ODPèDPDK Documentation & build > > > > > > Building on a vanilla Debian following the README.DPDK has not been > > totally > > > seamless... > > > > > > As I am not fully sure about my workarounds, it would be nice somebody > > > check and corrects the README.DPDK. > > > > > > Cordially, > > > > Hi Francois, > > > > The README file seems to be badly outdated. I'll create a patch to fix > the > > file tomorrow. > > > > P.S. odp-dpdk has own mailing list: [email protected]. > > > > -Matias > > > > > > > > > > François-Frédéric > > > > > > *git clone http://92.243.14.124/git/dpdk > > > <http://92.243.14.124/git/dpdk> ./dpdk* > > > > > > but this does not work: > > > Cloning into './dpdk'... > > > fatal: repository 'http://92.243.14.124/git/dpdk/' not found > > > > > > > > > so why not using the official link??? > > > > > > git clone git://dpdk.org/dpdk > > > Cloning into 'dpdk'... > > > remote: Counting objects: 54717, done. > > > remote: Compressing objects: 100% (11606/11606), done. > > > remote: Total 54717 (delta 43712), reused 53550 (delta 42797) > > > Receiving objects: 100% (54717/54717), 26.80 MiB | 425.00 KiB/s, done. > > > Resolving deltas: 100% (43712/43712), done. > > > Checking connectivity... done. > > > > > > > > > > > > *Set CONFIG_RTE_BUILD_COMBINE_LIBS=y* > > > This parameter does not exist (anymore ?) > > > > > > > > > *CONFIG_RTE_LIBRTE_IXGBE_ALLOW_UNSUPPORTED_SFP=y* > > > This parameter does not exist (anymore?) > > > > > > *build with EXTRA_CFLAGS="-fPIC"* > > > Does not produce the best code. Is there a reason for that ? > > > > > > *Dependence DPDK build* > > > No information on pre-requisites. You need to point to DPDK doc or to > > give > > > full build intructions or pre-requisites. > > > On a fresh Debian install you need: > > > apt-get install dkms libncurses5-dev libpcap-dev > > > > > > the make command lacks the DESTDIR parameter > > > make install T=x86_64-native-linuxapp-gcc EXTRA_CFLAGS="-fPIC" > > > DESTDIR=../dpdk-16.07/ > > > > > > > > > *odp-dpdk build* > > > > > > ./configure --with-platform=linux-dpdk --with-sdk-install-path=<dpdk- > > > dir>/x86_64-native-linuxapp-gcc > > > Should say it is the DPDK ABSOLUTE PATH, not relative! > > > > > > > > > lacks: > > > export RTE_SDK=<absoule path to DPDK> > > > export RTE_TARGET=x86_64-native-linuxapp-gcc > > > > > > *Checking compiled ODP with sample app* > > > > > > to run an ODP-dpdk app, it should be clear that it must be run as root > > and > > > that DPDK parameters are to be in a variable. > > > > > > sudo ODP_PLATFORM_PARAMS="-l0 --no-huge" ./odp_hello -c 0 -n 1 > > > > > > doing an export and just a sudo does not work. > > > > > > > > > -- > > > [image: Linaro] <http://www.linaro.org/> > > > François-Frédéric Ozog | *Director Linaro Networking Group* > > > T: +33.67221.6485 > > > [email protected] | Skype: ffozog > > >
