Bruno - You have made an assumption that historically vendors have tuned LSP transmission rates to a platform specific value. That certainly is not true in the case of my employer (happy to hear what other vendors have been doing for the past 20 years).
The default value is based on minimumBroadcastLSPTransmissionInterval specified in ISO10589. A knob is available to allow tuning (faster or slower) in a given deployment - though in my experience this knob is rarely used. We already discuss in https://tools.ietf.org/html/draft-ginsberg-lsr-isis-flooding-scale-02#section-2 that this common interpretation isn't the most appropriate, but historically the concern has been to avoid flooding too fast - not to optimize flooding speed. Obviously, we are revisiting that approach and saying it needs to change - which is something I think we have consensus on. I have provided a description in my recent response as to why it is difficult to derive an optimal value on a per platform basis. You may disagree - but please do not claim that we actually have been doing this for years. We haven't been. Les From: [email protected] <[email protected]> Sent: Monday, April 20, 2020 4:47 AM To: Les Ginsberg (ginsberg) <[email protected]> Cc: [email protected] Subject: RE: Flow Control Discussion for IS-IS Flooding Speed Les, After nearly 2 months, can we expect an answer from your side? More specifically, the below question [Bruno] _Assuming_ that the parameters are static, the parameters proposed in draft-decraene-lsr-isis-flooding-speed are the same as the one implemented (configured) on multiple implementations, including the one from your employer. Now do you believe that those parameters can be determined? § If yes, how do you do _today_ on your implementation? (this seems to contradict your statement that you have no way to figure out how to find the right value) § If no, why did you implement those parameters, and ask network operator to configure them? Thank you, --Bruno From: DECRAENE Bruno TGI/OLN Sent: Wednesday, February 26, 2020 8:03 PM To: 'Les Ginsberg (ginsberg)' Cc: [email protected]<mailto:[email protected]> Subject: RE: Flow Control Discussion for IS-IS Flooding Speed Les, Please see inline[Bruno] From: Lsr [mailto:[email protected]] On Behalf Of Les Ginsberg (ginsberg) Sent: Wednesday, February 19, 2020 3:32 AM To: [email protected]<mailto:[email protected]> Subject: Re: [Lsr] Flow Control Discussion for IS-IS Flooding Speed Base protocol operation of the Update process tracks the flooding of LSPs/interface and guarantees timer-based retransmission on P2P interfaces until an acknowledgment is received. Using this base protocol mechanism in combination with exponential backoff of the retransmission timer provides flow control in the event of temporary overload of the receiver. This mechanism works without protocol extensions, is dynamic, operates independent of the reason for delayed acknowledgment (dropped packets, CPU overload), and does not require additional signaling during the overloaded period. This is consistent with the recommendations in RFC 4222 (OSPF). Receiver-based flow control (as proposed in https://datatracker.ietf.org/doc/draft-decraene-lsr-isis-flooding-speed/ ) requires protocol extensions and introduces additional signaling during periods of high load. The asserted reason for this is to optimize throughput - but there is no evidence that it will achieve this goal. Mention has been made to TCP-like flow control mechanisms as a model - which are indeed receiver based. However, there are significant differences between TCP sessions and IGP flooding. TCP consists of a single session between two endpoints. Resources (primarily buffer space) for this session are typically allocated in the control plane and current usage is easily measurable.. IGP flooding is point-to-multi-point, resources to support IGP flooding involve both control plane queues and dataplane queues, both of which are typically not per interface - nor even dedicated to a particular protocol instance. What input is required to optimize receiver-based flow control is not fully specified. https://datatracker.ietf.org/doc/draft-decraene-lsr-isis-flooding-speed/ suggests (Section 5) that the values to be advertised: "use a formula based on an off line tests of the overall LSPDU processing speed for a particular set of hardware and the number of interfaces configured for IS-IS" implying that the advertised value is intentionally not dynamic. As such, it could just as easily be configured on the transmit side and not require additional signaling. As a static value, it would necessarily be somewhat conservative as it has to account for the worst case under the current configuration - which means it needs to consider concurrent use of the CPU and dataplane by all protocols/features which are enabled on a router - not all of whose use is likely to be synchronized with peak IS-IS flooding load. [Bruno] _Assuming_ that the parameters are static, those parameters o are the same as the one implemented (configured) on multiple implementations, including the one from your employer. Now do you believe that those parameters can be determined? § If yes, how do you do _today_ on your implementation? (this seems to contradict your statement that you have no way to figure out how to find the right value) § If no, why did you implement those parameters, and ask network operator to configure them? § There is also the option to reply: I don't know but don't care as I leave the issue to the network operator. o can still provide some form of dynamicity, by using the PSNP as dynamic acknowledgement. o are really dependent on the receiver, not the sender. § the sender will never overload itself. § The receiver has more information, knowing its processing power (low end, high end, 80s, 20s (currently we are stuck with 20 years old value assuming the worst possible receiver (and worst there were, including with packet processing partly done in the control plane processor)), its expected IS-IS load (#neighbors), its preference for bursty LSP reception (high delay between IS-IS CPU allocation cycles, memory not an issue up to x kilo-octet...), its expected control plane load if IS-IS traffic has not higher priority over other control plane traffic...), it's expected level of QoS prioritization [1] · [1] looks for "Extended SPD Headroom". E.g. "Since IGP and link stability are more tenuous and more crucial than BGP stability, such packets are now given the highest priority and are given extended SPD headroom with a default of 10 packets. This means that these packets are not dropped if the size of the input hold queue is lower than 185 (input queue default size + spd headroom size + spd extended headroom)." o And this is for distributed architecture, 15 years ago. So what about using the above number (in the router configuration), applies Tony's proposal (*oversubscription/number of IS neighbhors), and advertise this value to your LSP sender? [1] https://www.cisco.com/c/en/us/support/docs/routers/12000-series-routers/29920-spd.html - --Bruno Unless a good case can be made as to why transmit-based flow control is not a good fit and why receiver-based flow control is demonstrably better, it seems unnecessary to extend the protocol. Les From: Lsr <[email protected]<mailto:[email protected]>> On Behalf Of Les Ginsberg (ginsberg) Sent: Tuesday, February 18, 2020 6:25 PM To: [email protected]<mailto:[email protected]> Subject: [Lsr] Flow Control Discussion for IS-IS Flooding Speed Two recent drafts advocate for the use of faster LSP flooding speeds in IS-IS: https://datatracker.ietf.org/doc/draft-decraene-lsr-isis-flooding-speed/ https://datatracker.ietf.org/doc/draft-ginsberg-lsr-isis-flooding-scale/ There is strong agreement on two key points: 1)Modern networks require much faster flooding speeds than are commonly in use today 2)To deploy faster flooding speeds safely some form of flow control is needed The key point of contention between the two drafts is how flow control should be implemented. https://datatracker.ietf.org/doc/draft-decraene-lsr-isis-flooding-speed/ advocates for a receiver based flow control where the receiver advertises in hellos the parameters which indicate the rate/burst size which the receiver is capable of supporting on the interface. Senders are required to limit the rate of LSP transmission on that interface in accordance with the values advertised by the receiver. https://datatracker.ietf.org/doc/draft-ginsberg-lsr-isis-flooding-scale/ advocates for a transmit based flow control where the transmitter monitors the number of unacknowledged LSPs sent on each interface and implements a backoff algorithm to slow the rate of sending LSPs based on the length of the per interface unacknowledged queue. While other differences between the two drafts exist, it is fair to say that if agreement could be reached on the form of flow control then it is likely other issues could be resolved easily. This email starts the discussion regarding the flow control issue. _________________________________________________________________________________________________________________________ Ce message et ses pieces jointes peuvent contenir des informations confidentielles ou privilegiees et ne doivent donc pas etre diffuses, exploites ou copies sans autorisation. Si vous avez recu ce message par erreur, veuillez le signaler a l'expediteur et le detruire ainsi que les pieces jointes. Les messages electroniques etant susceptibles d'alteration, Orange decline toute responsabilite si ce message a ete altere, deforme ou falsifie. Merci. This message and its attachments may contain confidential or privileged information that may be protected by law; they should not be distributed, used or copied without authorisation. If you have received this email in error, please notify the sender and delete this message and its attachments. As emails may be altered, Orange is not liable for messages that have been modified, changed or falsified. Thank you.
_______________________________________________ Lsr mailing list [email protected] https://www.ietf.org/mailman/listinfo/lsr
