csütörtök 17 augusztus 2006 17.06 dátummal Jim McQuillan ezt írta:
> On Thu, August 17, 2006 2:45 am, Stefán István wrote:
> > szerda 16 augusztus 2006 16.33 dátummal Jim McQuillan ezt írta:
> >> On Wed, August 16, 2006 6:21 am, Stefán István wrote:
> >> > Hello!
> >> > I have a via c3 motherboard with integrated graphics chip. It's type
> >> is
> >> > VT8623
> >> > [Apollo CLE266] integrated CastleRock graphics.
> >> > It's pci id is: 1106:3122
> >> >
> >> > If I specify in the lts.conf to use the via driver, nothing appeares
> >> on
> >> > the
> >> > screen. But if I set to vesa it works. But I don't want to use the
> >> chip in
> >> > vesa mode for it is rather slow. Does anyone know which other driver
> >> could
> >> > work with this chip?
> >> >
> >>
> >>
> >> Is the screen completely blank?
> >>
> >> How about the LED on the monitor, does it glow orange? That could
> >> indicate that the card is over-driving the monitor, in which case, you'd
> >> need to specify a modeline or the horz/vert refresh frequencies in
> >> lts.conf
> >>
> >
> > The monitor says "no signal" and then blank completely and the led becomes
> > orange.
>
> Yep, the orange LED indicates that the frequency is out of range for the
> monitor.
>
> You'll need to specify values for X_HORZSYNC and X_VERTREFRESH
>
> Try something like:
>
> X_HORZSYNC = "60-70"
> X_VERTREFRESH = 60
>
> Add those lines to your lts.conf file and see if that helps.
Unfortunately it doesn't help. I added these lines to lts.conf:
X_VERTREFRESH = 50-75
X_HORZSYNC = 24-80
These are the values of Neovo F-417 lcd display.
I also tried to change the display to an crt monitor, but it doesn't work
either, only with vesa driver.
I didn't see any signs of error in the X log file, but a strange thing I
noticed: there is a tv out on the motherboard, and it is detected by X. Could
it be that X wants to use the tv out instead of the normal vga out?
Thanks,
Istvan
X Window System Version 6.9.0
Release Date: 21 December 2005
X Protocol Version 11, Revision 0, Release 6.9
Build Operating System: Linux 2.6.15-19-686 i686 [ELF]
Current Operating System: Linux wsteszt 2.6.16.1-ltsp-1 #1 PREEMPT Wed Mar 29 23:23:22 EST 2006 i686
Build Date: 03 April 2006
Before reporting problems, check http://wiki.X.Org
to make sure that you have the latest version.
Module Loader present
Markers: (--) probed, (**) from config file, (==) default setting,
(++) from command line, (!!) notice, (II) informational,
(WW) warning, (EE) error, (NI) not implemented, (??) unknown.
(==) Log file: "/var/log/Xorg.0.0.log", Time: Fri Aug 18 09:08:36 2006
(++) Using config file: "/tmp/XF86Config.1"
(==) ServerLayout "Xorg Configured"
(**) |-->Screen "Screen00" (0)
(**) | |-->Monitor "Monitor00"
(**) | |-->Device "Card00"
(**) |-->Input Device "Keyboard0"
(**) Option "XkbLayout" "hu"
(**) XKB: layout: "hu"
(==) Keyboard: CustomKeycode disabled
(**) |-->Input Device "Mouse0"
(**) |-->Input Device "Mouse1"
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/75dpi/,/usr/X11R6/lib/X11/fonts/100dpi/"
(**) RgbPath set to "/usr/X11R6/lib/X11/rgb"
(==) ModulePath set to "/usr/X11R6/lib/modules"
(II) Open ACPI successful (/proc/acpi/event)
(II) Module ABI versions:
X.Org ANSI C Emulation: 0.2
X.Org Video Driver: 0.8
X.Org XInput driver : 0.5
X.Org Server Extension : 0.2
X.Org Font Renderer : 0.4
(II) Loader running on linux
(II) LoadModule: "bitmap"
(II) Loading /usr/X11R6/lib/modules/fonts/libbitmap.so
(II) Module bitmap: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Bitmap
(II) LoadModule: "pcidata"
(II) Loading /usr/X11R6/lib/modules/libpcidata.so
(II) Module pcidata: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.8
(++) using VT number 1
(II) PCI: PCI scan (all values are in hex)
(II) PCI: 00:00:0: chip 1106,3123 card 1106,aa01 rev 00 class 06,00,00 hdr 00
(II) PCI: 00:01:0: chip 1106,b091 card 0000,0000 rev 00 class 06,04,00 hdr 01
(II) PCI: 00:0d:0: chip 1106,3044 card 1106,3044 rev 80 class 0c,00,10 hdr 00
(II) PCI: 00:10:0: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:1: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:2: chip 1106,3038 card 1106,3038 rev 80 class 0c,03,00 hdr 80
(II) PCI: 00:10:3: chip 1106,3104 card 1106,3104 rev 82 class 0c,03,20 hdr 00
(II) PCI: 00:11:0: chip 1106,3177 card 1106,aa01 rev 00 class 06,01,00 hdr 80
(II) PCI: 00:11:1: chip 1106,0571 card 1106,aa01 rev 06 class 01,01,8a hdr 00
(II) PCI: 00:11:5: chip 1106,3059 card 1106,aa01 rev 50 class 04,01,00 hdr 00
(II) PCI: 00:12:0: chip 1106,3065 card 1106,0102 rev 74 class 02,00,00 hdr 00
(II) PCI: 01:00:0: chip 1106,3122 card 1106,3122 rev 03 class 03,00,00 hdr 00
(II) PCI: End of PCI scan
(II) Host-to-PCI bridge:
(II) Bus 0: bridge is at (0:0:0), (0,0,1), BCTRL: 0x0008 (VGA_EN is set)
(II) Bus 0 I/O range:
[0] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) Bus 0 non-prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) Bus 0 prefetchable memory range:
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
(II) PCI-to-PCI bridge:
(II) Bus 1: bridge is at (0:1:0), (0,1,1), BCTRL: 0x000c (VGA_EN is set)
(II) Bus 1 non-prefetchable memory range:
[0] -1 0 0xe4000000 - 0xe5ffffff (0x2000000) MX[B]
(II) Bus 1 prefetchable memory range:
[0] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B]
(II) PCI-to-ISA bridge:
(II) Bus -1: bridge is at (0:17:0), (0,-1,-1), BCTRL: 0x0008 (VGA_EN is set)
(--) PCI:*(1:0:0) unknown vendor (0x1106) unknown chipset (0x3122) rev 3, Mem @ 0xe0000000/26, 0xe4000000/24
(II) Addressable bus resource ranges are
[0] -1 0 0x00000000 - 0xffffffff (0x0) MX[B]
[1] -1 0 0x00000000 - 0x0000ffff (0x10000) IX[B]
(II) OS-reported resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) PCI Memory resource overlap reduced 0xe6000000 from 0xe6ffffff to 0xe5ffffff
(II) Active PCI resource ranges:
[0] -1 0 0xe7002000 - 0xe70020ff (0x100) MX[B]
[1] -1 0 0xe7001000 - 0xe70010ff (0x100) MX[B]
[2] -1 0 0xe7000000 - 0xe70007ff (0x800) MX[B]
[3] -1 0 0xe6000000 - 0xe5ffffff (0x0) MX[B]O
[4] -1 0 0xe4000000 - 0xe4ffffff (0x1000000) MX[B](B)
[5] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[6] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[7] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[8] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[9] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[10] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[11] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[12] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
(II) Active PCI resource ranges after removing overlaps:
[0] -1 0 0xe7002000 - 0xe70020ff (0x100) MX[B]
[1] -1 0 0xe7001000 - 0xe70010ff (0x100) MX[B]
[2] -1 0 0xe7000000 - 0xe70007ff (0x800) MX[B]
[3] -1 0 0xe6000000 - 0xe5ffffff (0x0) MX[B]O
[4] -1 0 0xe4000000 - 0xe4ffffff (0x1000000) MX[B](B)
[5] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[6] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[7] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[8] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[9] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[10] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[11] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[12] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
(II) OS-reported resource ranges after removing overlaps with PCI:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[6] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
(II) All system resource ranges:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe7002000 - 0xe70020ff (0x100) MX[B]
[6] -1 0 0xe7001000 - 0xe70010ff (0x100) MX[B]
[7] -1 0 0xe7000000 - 0xe70007ff (0x800) MX[B]
[8] -1 0 0xe6000000 - 0xe5ffffff (0x0) MX[B]O
[9] -1 0 0xe4000000 - 0xe4ffffff (0x1000000) MX[B](B)
[10] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[13] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[14] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[15] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[16] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[17] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[18] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[19] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
(II) LoadModule: "extmod"
(II) Loading /usr/X11R6/lib/modules/extensions/libextmod.so
(II) Module extmod: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org Server Extension
ABI class: X.Org Server Extension, version 0.2
(II) Loading extension SHAPE
(II) Loading extension MIT-SUNDRY-NONSTANDARD
(II) Loading extension BIG-REQUESTS
(II) Loading extension SYNC
(II) Loading extension MIT-SCREEN-SAVER
(II) Loading extension XC-MISC
(II) Loading extension XFree86-VidModeExtension
(II) Loading extension XFree86-Misc
(II) Loading extension XFree86-DGA
(II) Loading extension DPMS
(II) Loading extension TOG-CUP
(II) Loading extension Extended-Visual-Information
(II) Loading extension XVideo
(II) Loading extension XVideo-MotionCompensation
(II) Loading extension X-Resource
(II) LoadModule: "freetype"
(II) Loading /usr/X11R6/lib/modules/fonts/libfreetype.so
(II) Module freetype: vendor="X.Org Foundation & the After X-TT Project"
compiled for 6.9.0, module version = 2.1.0
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font FreeType
(II) LoadModule: "type1"
(II) Loading /usr/X11R6/lib/modules/fonts/libtype1.so
(II) Module type1: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.2
Module class: X.Org Font Renderer
ABI class: X.Org Font Renderer, version 0.4
(II) Loading font Type1
(II) Loading font CID
(II) LoadModule: "via"
(II) Loading /usr/X11R6/lib/modules/drivers/via_drv.so
(II) Module via: vendor="X.Org Foundation"
compiled for 4.3.99.902, module version = 0.1.33
Module class: X.Org Video Driver
ABI class: X.Org Video Driver, version 0.8
(II) LoadModule: "keyboard"
(II) Loading /usr/X11R6/lib/modules/input/keyboard_drv.so
(II) Module keyboard: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.5
(II) LoadModule: "mouse"
(II) Loading /usr/X11R6/lib/modules/input/mouse_drv.so
(II) Module mouse: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.3
Module class: X.Org XInput Driver
ABI class: X.Org XInput driver, version 0.5
(II) VIA: driver for VIA chipsets: CLE266, KM400/KN400, K8M800,
PM800/PM880/CN400
(II) Primary Device is: PCI 01:00:0
(--) Assigning device section with no busID to primary device
(--) Chipset CLE266 found
(!!) VIA Technologies does not support or endorse this driver in any way.
(!!) For support please contact the driver maintainer or your X vendor.
(II) resource ranges after xf86ClaimFixedResources() call:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe7002000 - 0xe70020ff (0x100) MX[B]
[6] -1 0 0xe7001000 - 0xe70010ff (0x100) MX[B]
[7] -1 0 0xe7000000 - 0xe70007ff (0x800) MX[B]
[8] -1 0 0xe6000000 - 0xe5ffffff (0x0) MX[B]O
[9] -1 0 0xe4000000 - 0xe4ffffff (0x1000000) MX[B](B)
[10] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[11] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[12] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[13] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[14] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[15] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[16] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[17] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[18] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[19] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
(II) resource ranges after probing:
[0] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[1] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[2] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[3] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[4] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[5] -1 0 0xe7002000 - 0xe70020ff (0x100) MX[B]
[6] -1 0 0xe7001000 - 0xe70010ff (0x100) MX[B]
[7] -1 0 0xe7000000 - 0xe70007ff (0x800) MX[B]
[8] -1 0 0xe6000000 - 0xe5ffffff (0x0) MX[B]O
[9] -1 0 0xe4000000 - 0xe4ffffff (0x1000000) MX[B](B)
[10] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[11] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[12] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[13] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[14] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[15] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[16] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[17] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[18] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[19] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[20] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[21] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[22] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
[23] 0 0 0xe50003b0 - 0xe50003bb (0xc) IS[B]
[24] 0 0 0xe50003c0 - 0xe50003df (0x20) IS[B]
(II) Setting vga for screen 0.
(II) Loading sub module "vgahw"
(II) LoadModule: "vgahw"
(II) Loading /usr/X11R6/lib/modules/libvgahw.so
(II) Module vgahw: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.8
(**) VIA(0): Depth 16, (--) framebuffer bpp 16
(==) VIA(0): RGB weight 565
(==) VIA(0): Default visual is TrueColor
(==) VIA(0): Using HW cursor
(--) VIA(0): Chipset: "CLE266"
(--) VIA(0): mapping MMIO @ 0xe4000000 with size 0x9000
(--) VIA(0): mapping BitBlt MMIO @ 0xe4200000 with size 0x10000
(II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(--) VIA(0): Chipset Rev.: 18
(WW) VIA(0): Manufacturer plainly copied main PCI ids to Subsystem/Card ids.
(--) VIA(0): Detected VIA EPIA M/MII/....
(==) VIA(0): Using gamma correction (1.0, 1.0, 1.0)
(--) VIA(0): videoram = 32768k
(II) Loading sub module "i2c"
(II) LoadModule: "i2c"
(II) Loading /usr/X11R6/lib/modules/libi2c.so
(II) Module i2c: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.8
(II) VIA(0): I2C bus "I2C bus 1" initialized.
(II) VIA(0): I2C bus "I2C bus 2" initialized.
(II) VIA(0): I2C bus "I2C bus 3" initialized.
(II) Loading sub module "ddc"
(II) LoadModule: "ddc"
(II) Loading /usr/X11R6/lib/modules/libddc.so
(II) Module ddc: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org Video Driver, version 0.8
(II) VIA(0): I2C device "I2C bus 1:ddc2" registered at address 0xA0.
(II) VIA(0): I2C device "I2C bus 1:ddc2" removed.
(II) VIA(0): Manufacturer: PHL Model: 18 Serial#: 356217
(II) VIA(0): Year: 2006 Week: 3
(II) VIA(0): EDID Version: 1.3
(II) VIA(0): Analog Display Input, Input Voltage Level: 0.700/0.700 V
(II) VIA(0): Sync: Separate
(II) VIA(0): Max H-Image Size [cm]: horiz.: 31 vert.: 23
(II) VIA(0): Gamma: 2.80
(II) VIA(0): DPMS capabilities: Off; RGB/Color Display
(II) VIA(0): First detailed timing not preferred mode in violation of standard!(II) VIA(0): redX: 0.620 redY: 0.350 greenX: 0.290 greenY: 0.610
(II) VIA(0): blueX: 0.150 blueY: 0.065 whiteX: 0.283 whiteY: 0.297
(II) VIA(0): Supported VESA Video Modes:
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): [EMAIL PROTECTED]
(II) VIA(0): Manufacturer's mask: 0
(II) VIA(0): Supported Future Video Modes:
(II) VIA(0): #0: hsize: 640 vsize 480 refresh: 85 vid: 22833
(II) VIA(0): #1: hsize: 800 vsize 600 refresh: 85 vid: 22853
(II) VIA(0): #2: hsize: 1024 vsize 768 refresh: 85 vid: 22881
(II) VIA(0): #3: hsize: 1280 vsize 1024 refresh: 60 vid: 32897
(II) VIA(0): #4: hsize: 640 vsize 480 refresh: 100 vid: 26673
(II) VIA(0): #5: hsize: 800 vsize 600 refresh: 100 vid: 26693
(II) VIA(0): #6: hsize: 1280 vsize 960 refresh: 60 vid: 16513
(II) VIA(0): #7: hsize: 1152 vsize 864 refresh: 75 vid: 20337
(II) VIA(0): Supported additional Video Mode:
(II) VIA(0): clock: 25.2 MHz Image Size: 306 x 230 mm
(II) VIA(0): h_active: 640 h_sync: 656 h_sync_end 752 h_blank_end 800 h_border: 0
(II) VIA(0): v_active: 350 v_sync: 387 v_sync_end 389 v_blanking: 449 v_border: 0
(II) VIA(0): Serial No: BZ 356217
(II) VIA(0): Monitor name: PH107E/V/S/G6
(II) VIA(0): Ranges: V min: 50 V max: 160 Hz, H min: 30 H max: 71 kHz, PixClock max 120 MHz
(II) VIA(0): I2C device "I2C bus 2:VT162x" registered at address 0x40.
(--) VIA(0): Detected VIA Technologies VT1622 TV Encoder
(--) VIA(0): VT162x: Nothing connected.
(II) VIA(0): Monitor00: Using hsync range of 31.00-62.00 kHz
(II) VIA(0): Monitor00: Using vrefresh range of 55.00-90.00 Hz
(II) VIA(0): Clock range: 20.00 to 230.00 MHz
(II) VIA(0): Not using default mode "320x175" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "320x200" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "360x200" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "320x240" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "400x300" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (interlace mode not supported)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (hsync out of range)
(II) VIA(0): Not using default mode "512x384" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1152x864" (hsync out of range)
(II) VIA(0): Not using default mode "576x432" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(WW) (1280x960,Monitor00) mode clock 148.5MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1280x960" (hsync out of range)
(II) VIA(0): Not using default mode "640x480" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1280x1024" (hsync out of range)
(II) VIA(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(WW) (1280x1024,Monitor00) mode clock 135MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1280x1024" (hsync out of range)
(II) VIA(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(WW) (1280x1024,Monitor00) mode clock 157.5MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1280x1024" (hsync out of range)
(II) VIA(0): Not using default mode "640x512" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor00) mode clock 162MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor00) mode clock 175.5MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor00) mode clock 189MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor00) mode clock 202.5MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1600x1200,Monitor00) mode clock 229.5MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1600x1200" (hsync out of range)
(II) VIA(0): Not using default mode "800x600" (bad mode clock/interlace/doublescan)
(WW) (1792x1344,Monitor00) mode clock 204.8MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1792x1344" (hsync out of range)
(II) VIA(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1792x1344" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "896x672" (bad mode clock/interlace/doublescan)
(WW) (1856x1392,Monitor00) mode clock 218.3MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1856x1392" (hsync out of range)
(II) VIA(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1856x1392" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "928x696" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "416x312" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "576x384" (bad mode clock/interlace/doublescan)
(WW) (1400x1050,Monitor00) mode clock 122MHz exceeds DDC maximum 120MHz
(II) VIA(0): Not using default mode "1400x1050" (hsync out of range)
(II) VIA(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VIA(0): CrtcHSyncEnd out of range.
(II) VIA(0): Not using default mode "1400x1050" (horizontal sync too wide)
(II) VIA(0): Not using default mode "700x525" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1600x1024" (no clock available for mode)
(II) VIA(0): Not using default mode "800x512" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1920x1440" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "960x720" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "2048x1536" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1024x768" (bad mode clock/interlace/doublescan)
(II) VIA(0): Not using default mode "1280x960" (width too large for virtual size)
(II) VIA(0): Not using default mode "1152x768" (width too large for virtual size)
(--) VIA(0): Virtual size is 1024x768 (pitch 1024)
(**) VIA(0): *Default mode "1024x768": 78.8 MHz (scaled from -299.7 MHz), 60.1 kHz, 75.1 Hz
(II) VIA(0): Modeline "1024x768" 78.80 1024 1040 1136 1312 768 769 772 800 +hsync +vsync
(**) VIA(0): *Default mode "800x600": 56.3 MHz (scaled from -328.2 MHz), 53.7 kHz, 85.1 Hz
(II) VIA(0): Modeline "800x600" 56.30 800 832 896 1048 600 601 604 631 +hsync +vsync
(**) VIA(0): *Default mode "640x480": 36.0 MHz (scaled from -275.5 MHz), 43.3 kHz, 85.0 Hz
(II) VIA(0): Modeline "640x480" 36.00 640 696 752 832 480 481 484 509 -hsync -vsync
(**) VIA(0): Default mode "1024x768": 75.0 MHz (scaled from -440.1 MHz), 56.5 kHz, 70.1 Hz
(II) VIA(0): Modeline "1024x768" 75.00 1024 1048 1184 1328 768 771 777 806 -hsync -vsync
(**) VIA(0): Default mode "1024x768": 65.0 MHz (scaled from 796.0 MHz), 48.4 kHz, 60.0 Hz
(II) VIA(0): Modeline "1024x768" 65.00 1024 1048 1184 1344 768 771 777 806 -hsync -vsync
(**) VIA(0): Default mode "832x624": 57.3 MHz (scaled from 799.9 MHz), 49.7 kHz, 74.6 Hz
(II) VIA(0): Modeline "832x624" 57.28 832 864 928 1152 624 625 628 667 -hsync -vsync
(**) VIA(0): Default mode "800x600": 49.5 MHz (scaled from -579.5 MHz), 46.9 kHz, 75.0 Hz
(II) VIA(0): Modeline "800x600" 49.50 800 816 896 1056 600 601 604 625 +hsync +vsync
(**) VIA(0): Default mode "800x600": 50.0 MHz (scaled from 241.8 MHz), 48.1 kHz, 72.2 Hz
(II) VIA(0): Modeline "800x600" 50.00 800 856 976 1040 600 637 643 666 +hsync +vsync
(**) VIA(0): Default mode "800x600": 40.0 MHz (scaled from -127.7 MHz), 37.9 kHz, 60.3 Hz
(II) VIA(0): Modeline "800x600" 40.00 800 840 968 1056 600 601 605 628 +hsync +vsync
(**) VIA(0): Default mode "800x600": 36.0 MHz (scaled from -275.5 MHz), 35.2 kHz, 56.2 Hz
(II) VIA(0): Modeline "800x600" 36.00 800 824 896 1024 600 601 603 625 +hsync +vsync
(**) VIA(0): Default mode "640x480": 31.5 MHz (scaled from 361.1 MHz), 37.5 kHz, 75.0 Hz
(II) VIA(0): Modeline "640x480" 31.50 640 656 720 840 480 481 484 500 -hsync -vsync
(**) VIA(0): Default mode "640x480": 31.5 MHz (scaled from 361.1 MHz), 37.9 kHz, 72.8 Hz
(II) VIA(0): Modeline "640x480" 31.50 640 664 704 832 480 489 491 520 -hsync -vsync
(**) VIA(0): Default mode "640x480": 25.2 MHz (scaled from -674.5 MHz), 31.5 kHz, 60.0 Hz
(II) VIA(0): Modeline "640x480" 25.20 640 656 752 800 480 490 492 525 -hsync -vsync
(**) VIA(0): Default mode "720x400": 35.5 MHz (scaled from 508.8 MHz), 37.9 kHz, 85.0 Hz
(II) VIA(0): Modeline "720x400" 35.50 720 756 828 936 400 401 404 446 -hsync +vsync
(**) VIA(0): Default mode "640x400": 31.5 MHz (scaled from 361.1 MHz), 37.9 kHz, 85.1 Hz
(II) VIA(0): Modeline "640x400" 31.50 640 672 736 832 400 401 404 445 -hsync +vsync
(**) VIA(0): Default mode "640x350": 31.5 MHz (scaled from 361.1 MHz), 37.9 kHz, 85.1 Hz
(II) VIA(0): Modeline "640x350" 31.50 640 672 736 832 350 382 385 445 +hsync -vsync
(--) VIA(0): Display dimensions: (310, 230) mm
(--) VIA(0): DPI set to (83, 84)
(II) Loading sub module "fb"
(II) LoadModule: "fb"
(II) Loading /usr/X11R6/lib/modules/libfb.so
(II) Module fb: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.0.0
ABI class: X.Org ANSI C Emulation, version 0.2
(II) Loading sub module "xaa"
(II) LoadModule: "xaa"
(II) Loading /usr/X11R6/lib/modules/libxaa.so
(II) Module xaa: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 1.2.0
ABI class: X.Org Video Driver, version 0.8
(II) Loading sub module "ramdac"
(II) LoadModule: "ramdac"
(II) Loading /usr/X11R6/lib/modules/libramdac.so
(II) Module ramdac: vendor="X.Org Foundation"
compiled for 6.9.0, module version = 0.1.0
ABI class: X.Org Video Driver, version 0.8
(II) do I need RAC? No, I don't.
(II) resource ranges after preInit:
[0] 0 0 0xe4000000 - 0xe4ffffff (0x1000000) MS[B]
[1] 0 0 0xe0000000 - 0xe3ffffff (0x4000000) MS[B]
[2] -1 0 0xffe00000 - 0xffffffff (0x200000) MX[B](B)
[3] -1 0 0x00100000 - 0x3fffffff (0x3ff00000) MX[B]E(B)
[4] -1 0 0x000f0000 - 0x000fffff (0x10000) MX[B]
[5] -1 0 0x000c0000 - 0x000effff (0x30000) MX[B]
[6] -1 0 0x00000000 - 0x0009ffff (0xa0000) MX[B]
[7] -1 0 0xe7002000 - 0xe70020ff (0x100) MX[B]
[8] -1 0 0xe7001000 - 0xe70010ff (0x100) MX[B]
[9] -1 0 0xe7000000 - 0xe70007ff (0x800) MX[B]
[10] -1 0 0xe6000000 - 0xe5ffffff (0x0) MX[B]O
[11] -1 0 0xe4000000 - 0xe4ffffff (0x1000000) MX[B](B)
[12] -1 0 0xe0000000 - 0xe3ffffff (0x4000000) MX[B](B)
[13] 0 0 0x000a0000 - 0x000affff (0x10000) MS[B]
[14] 0 0 0x000b0000 - 0x000b7fff (0x8000) MS[B]
[15] 0 0 0x000b8000 - 0x000bffff (0x8000) MS[B]
[16] -1 0 0x0000ffff - 0x0000ffff (0x1) IX[B]
[17] -1 0 0x00000000 - 0x000000ff (0x100) IX[B]
[18] -1 0 0x0000ec00 - 0x0000ecff (0x100) IX[B]
[19] -1 0 0x0000e400 - 0x0000e4ff (0x100) IX[B]
[20] -1 0 0x0000e000 - 0x0000e00f (0x10) IX[B]
[21] -1 0 0x0000dc00 - 0x0000dc1f (0x20) IX[B]
[22] -1 0 0x0000d800 - 0x0000d81f (0x20) IX[B]
[23] -1 0 0x0000d400 - 0x0000d41f (0x20) IX[B]
[24] -1 0 0x0000d000 - 0x0000d07f (0x80) IX[B]
[25] 0 0 0xe50003b0 - 0xe50003bb (0xc) IS[B]
[26] 0 0 0xe50003c0 - 0xe50003df (0x20) IS[B]
(--) VIA(0): mapping framebuffer @ 0xe0000000 with size 0x2000000
(==) VIA(0): Removed MMIO write-combining range (0xe0000000,0x800000)
(==) VIA(0): Write-combining range (0xe0000000,0x2000000)
(--) VIA(0): Frame buffer start: 0xb5b6b000, free start: 0x180000 end: 0x2000000
(--) VIA(0): mapping MMIO @ 0xe4000000 with size 0x9000
(--) VIA(0): mapping BitBlt MMIO @ 0xe4200000 with size 0x10000
(II) VIA(0): vgaHWGetIOBase: hwp->IOBase is 0x03d0, hwp->PIOOffset is 0x0000
(II) VIA(0): 3D Engine has been initialized.
(II) VIA(0): VIAInternalScreenInit
(II) VIA(0): Using XFree86 Acceleration Architecture (XAA)
Screen to screen bit blits
Solid filled rectangles
8x8 mono pattern filled rectangles
8x8 color pattern filled rectangles
Solid Lines
Dashed Lines
Image Writes
Offscreen Pixmaps
Setting up tile and stipple cache:
32 128x128 slots
10 256x256 slots
32 8x8 color pattern slots
(==) VIA(0): Backing store disabled
(II) VIA(0): direct rendering disabled
(II) VIA(0): Benchmarking video copy. Less is better.
(--) VIA(0): Timed libc YUV420 copy... 4655852. Throughput: 76.4 MiB/s.
(--) VIA(0): Timed kernel YUV420 copy... 4630745. Throughput: 76.9 MiB/s.
(--) VIA(0): Ditch SSE YUV420 copy... Not supported by CPU.
(--) VIA(0): Timed MMX YUV420 copy... 3164187. Throughput: 112.5 MiB/s.
(--) VIA(0): Timed 3DNow! YUV420 copy... 3178488. Throughput: 112.0 MiB/s.
(--) VIA(0): Ditch MMX2 YUV420 copy... Not supported by CPU.
(--) VIA(0): Using MMX YUV42X copy for video.
(WW) VIA(0): [XvMC] Cannot use XvMC without DRI!
(==) RandR enabled
(II) Setting vga for screen 0.
(II) Initializing built-in extension MIT-SHM
(II) Initializing built-in extension XInputExtension
(II) Initializing built-in extension XTEST
(II) Initializing built-in extension XKEYBOARD
(II) Initializing built-in extension LBX
(II) Initializing built-in extension XC-APPGROUP
(II) Initializing built-in extension SECURITY
(II) Initializing built-in extension XINERAMA
(II) Initializing built-in extension XFIXES
(II) Initializing built-in extension XFree86-Bigfont
(II) Initializing built-in extension RENDER
(II) Initializing built-in extension RANDR
(II) Initializing built-in extension COMPOSITE
(II) Initializing built-in extension DAMAGE
(II) Initializing built-in extension XEVIE
(**) Option "CoreKeyboard"
(**) Keyboard0: Core Keyboard
(**) Option "Protocol" "standard"
(**) Keyboard0: Protocol: standard
(**) Option "AutoRepeat" "500 30"
(**) Option "XkbRules" "xorg"
(**) Keyboard0: XkbRules: "xorg"
(**) Option "XkbModel" "pc105"
(**) Keyboard0: XkbModel: "pc105"
(**) Keyboard0: XkbLayout: "hu"
(**) Option "CustomKeycodes" "off"
(**) Keyboard0: CustomKeycodes disabled
(**) Option "Protocol" "IMPS/2"
(**) Mouse0: Device: "/dev/psaux"
(**) Mouse0: Protocol: "IMPS/2"
(**) Option "CorePointer"
(**) Mouse0: Core Pointer
(**) Option "Device" "/dev/psaux"
(**) Option "Buttons" "5"
(**) Option "Emulate3Buttons" "off"
(**) Option "ZAxisMapping" "4 5"
(**) Mouse0: ZAxisMapping: buttons 4 and 5
(**) Mouse0: Buttons: 9
(**) Option "Resolution" "400"
(**) Mouse0: Resolution: 400
(**) Option "BaudRate" "1200"
(**) Mouse0: BaudRate: 1200
(**) Option "Protocol" "PS/2"
(**) Mouse1: Device: "/dev/input/mice"
(**) Mouse1: Protocol: "PS/2"
(**) Option "AlwaysCore"
(**) Mouse1: always reports core events
(**) Option "Device" "/dev/input/mice"
(**) Option "Buttons" "3"
(**) Option "Emulate3Buttons" "off"
(**) Option "ZAxisMapping" "4 5"
(**) Mouse1: ZAxisMapping: buttons 4 and 5
(**) Mouse1: Buttons: 9
(WW) Option "Resolution" requires an integer value
(WW) Option "BaudRate" requires an integer value
(II) XINPUT: Adding extended input device "Mouse1" (type: MOUSE)
(II) XINPUT: Adding extended input device "Mouse0" (type: MOUSE)
(II) XINPUT: Adding extended input device "Keyboard0" (type: KEYBOARD)
(II) Mouse0: ps2EnableDataReporting: succeeded
(II) Mouse1: ps2EnableDataReporting: succeeded
-------------------------------------------------------------------------
Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
_____________________________________________________________________
Ltsp-discuss mailing list. To un-subscribe, or change prefs, goto:
https://lists.sourceforge.net/lists/listinfo/ltsp-discuss
For additional LTSP help, try #ltsp channel on irc.freenode.net
