Tratande de hacer que funcione un modem isa , y leyendo lo que respecta a modems , hice lo siguiente :
En una parte decia que debia ver cuales eran las direcciones de entrada y salida y si se estaba instalado en windows se podia consultar en los recursos para ver estos datos , lo hice y los datos que pude sacar son los siguientes (en w98) rango 02f8-02ff y la interrupcion era 12 instalado en el com2 busque despues el archivo /etc/isapnp y como no lo tenia cree el esqueleto de este archivo con pnpdump > /etc/isapnp.conf luego me indicaba que debia buscar en este archivo los datos referidos a mi modem y activarlo sacando en simbolo de la izquierda # , lo que debia buscar era # (IO 0 (BASE 0x0NNN) # (INT 0 (IRQ MM (MODE + E ))) donde NNN es el rango de entrada salida y MM la interrupcion , luego al final debia sacar el simbolo a la linea # (ACT Y) con esto y con que figurara la linea /etc/isapnp.conf en los scrip de arranque debia ser suficiente , en esto no toque nada ya que decia que en versiones superiores a la 2.0 ya venia la invocacion . Archivo isapnp.conf (EN ESTE ARCHIVO DESMARQUE UNAS LINEAS PERO NO SE SI SON LAS CORRECTAS??? # $Id: pnpdump_main.c,v 1.27 2001/04/30 21:54:53 fox Exp $ # Release isapnptools-1.26 # # This is free software, see the sources for details. # This software has NO WARRANTY, use at your OWN RISK # # For details of the output file format, see isapnp.conf(5) # # For latest information and FAQ on isapnp and pnpdump see: # http://www.roestock.demon.co.uk/isapnptools/ # # Compiler flags: -DREALTIME -DHAVE_PROC -DENABLE_PCI -DHAVE_SCHED_SETSCHEDULER -DHAVE_NANOSLEEP -DWANT_TO_VALIDATE # # Trying port address 0273 # Board 1 has serial identifier 29 71 11 0a 99 50 02 73 4a # (DEBUG) (READPORT 0x0273) (ISOLATE PRESERVE) (IDENTIFY *) (VERBOSITY 2) (CONFLICT (IO FATAL)(IRQ FATAL)(DMA FATAL)(MEM FATAL)) # or WARNING # Card 1: (serial identifier 29 71 11 0a 99 50 02 73 4a) # Vendor Id RSS0250, Serial Number 1896942233, checksum 0x29. # Version 1.0, Vendor version 0.0 # ANSI string -->Genius GM56flex Plug & Play Modem <-- # # Logical device id RSS0251 # Device supports I/O range check register # Device supports vendor reserved register @ 0x39 # Device supports vendor reserved register @ 0x3b # Device supports vendor reserved register @ 0x3d # # Edit the entries below to uncomment out the configuration required. # Note that only the first value of any range is given, this may be changed if required # Don't forget to uncomment the activate (ACT Y) when happy (CONFIGURE RSS0250/1896942233 (LD 0 # Multiple choice time, choose one only ! # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03f8 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03f8) (CHECK)) # IRQ 4. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 4 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02f8 # Maximum IO base address 0x02f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x02f8) (CHECK)) # IRQ 3. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK)) # IRQ 4. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 4 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02e8 # Maximum IO base address 0x02e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x02e8) (CHECK)) # IRQ 3. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK)) # IRQ 5. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02e8 # Maximum IO base address 0x02e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x02e8) (CHECK)) # IRQ 7. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 7 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03f8 # Maximum IO base address 0x03f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03f8) (CHECK)) # IRQ 5, 7, 9, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02f8 # Maximum IO base address 0x02f8 # IO base alignment 8 bytes # Number of IO addresses required: 8 (IO 0 (SIZE 8) (BASE 0x02f8) (CHECK)) <<<<<<<<< IRQ 5, 7, 9, 10, 11, 12 or 15. <<<<<<<<< # High true, edge sensitive interrupt (by default) (INT 0 (IRQ 12 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x03e8 # Maximum IO base address 0x03e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x03e8) (CHECK)) # IRQ 7, 9, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 7 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x02e8 # Maximum IO base address 0x02e8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x02e8) (CHECK)) # IRQ 5, 9, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 5 (MODE +E))) # Start dependent functions: priority acceptable # Logical device decodes 16 bit IO address lines # Minimum IO base address 0x0100 # Maximum IO base address 0xfff8 # IO base alignment 8 bytes # Number of IO addresses required: 8 # (IO 0 (SIZE 8) (BASE 0x0100) (CHECK)) # IRQ 3, 4, 5, 7, 9, 10, 11, 12 or 15. # High true, edge sensitive interrupt (by default) # (INT 0 (IRQ 3 (MODE +E))) # End dependent functions (NAME "RSS0250/1896942233[0]{Genius GM56flex Plug & Play Modem }") (ACT Y) <<<<<<<<<< )) # End tag... Checksum 0x00 (OK) # Returns all cards to the "Wait for Key" state (WAITFORKEY) Ahora debia configurar los puertos serie , en esto en donde mas dudas tengo Para hacerlo indicaba usar setserial para leer la configuracion . La primera vez que lo hice me dio : setserial /dev/ttyS1 /dev/ttyS1 , UART : 16550A, Port:0x02f8 ,irq 3 luego me indicaba como configurar los ptos y como los valores que yo tenia es que debia usar la interrupcion 12 hice setserial /dev/ttyS1 irq 12 autonfig Para comprobar lo configurado une minicom y en la configuracion del pto serie le indique el com 2 para que se comunique y cuando intento probar la comunicacion con el modem por medio del comando AT no aparece nada , queda titilando el cursor y nada mas , cuando deberia haber dado una respuesta inmendiata .. Puntualmete PARA SEGUIR ..... , que es lo que configure mal o que es lo que no hice . Desde ya muchas gracias . -- Para desuscribirte tenés que visitar la página https://listas.linux.org.ar/mailman/listinfo/lugar-gral/ /* Publica y encontra trabajo relacionado con softlibre en http://www.usla.org.ar/modules/jobs/ */ Si tenés algún inconveniente o consulta escribí a mailto:[EMAIL PROTECTED]
