existe algo asi como el ndiswrapper pero para webcams? On Thu, Feb 21, 2008 at 4:27 PM, SISMONDA, Fernando <[EMAIL PROTECTED]> wrote: > Con el ndiswrapper hice andar esa placa yo. > > Yo tengo una hp6448se que tiene esa misma placa. > > Lo que había tomado nota es esto. > > //Deshabilitas el driver que venía > #echo 'blacklist bcm43xx' | sudo tee -a /etc/modprobe.d/blacklist > #sudo rmmod bcm43xx > > //Instalas este wrapper para drivers de windows > #sudo apt-get install ndiswrapper-common ndiswrapper-utils-1.9 > > //Instalas el driver de windows > //Lo tenes que sacar de los drivers de tu máquina > //Si no lo tenes, te puedo dar el que me funcionó a mi > #sudo ndiswrapper -i bcmwl5.inf > > //Genero la vinculación entre el dispositivo y wlan0 > #sudo ndiswrapper -m > > //Subo el módulo, si no te anda directamente, reinicia el equipo. > #sudo modprobe ndiswrapper > > Saludos > > -- > SISMONDA, Fernando > Cel: 1560027849 > > > > > Quoting Mauro Graziosi <[EMAIL PROTECTED]>: > > > Comento mis avances: > > > >> Ayer me enteré de este, fijate si te sirve: > >> http://wifi-radar.systemimager.org/ > >> http://www.linux.com/articles/55647 > > Voy a tratar de dar el mayor de detalle posible > > > > lspci > > Network controller: Broadcom Corporation BCM94311MCG wlan mini-PCI (rev 01) > > > > lsmod > > bcm43xx 127336 0 > > ieee80211softmac 31360 1 bcm43xx > > ieee80211 35656 2 bcm43xx,ieee80211softmac > > > > > > Configuraciones al inicio o luego de hacer /etc/init.d/networking > > restart (o simplemente start) > > > > ifconfig > > eth1 Link encap:Ethernet HWaddr 00:1A:73:4E:BB:CD > > UP DIFUSIÃ"N MULTICAST MTU:1500 Metric:1 > > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:78 errors:0 dropped:0 overruns:0 carrier:0 > > colisiones:0 txqueuelen:1000 > > RX bytes:0 (0.0 b) TX bytes:3276 (3.1 KB) > > Interrupt:10 > > > > iwconfig > > eth1 IEEE 802.11b/g ESSID:off/any Nickname:"Broadcom 4311" > > Mode:Managed Frequency=2.472 GHz Access Point: Invalid > > Bit Rate=1 Mb/s Tx-Power=18 dBm > > RTS thr:off Fragment thr:off > > Encryption key:off > > Link Quality=0/100 Signal level=-256 dBm Noise level=-256 dBm > > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > > Tx excessive retries:0 Invalid misc:0 Missed beacon:0 > > > > route > > Destination Gateway Genmask Flags Metric Ref Use > Iface > > 192.168.7.0 * 255.255.255.0 U 0 0 0 > eth0 > > 169.254.0.0 * 255.255.0.0 U 1000 0 0 > eth0 > > > > ---------------------- > > Luego de ejecutar el comando ifup eth1 > > > > ifconfig > > eth1 Link encap:Ethernet HWaddr 00:1A:73:4E:BB:CD > > inet addr:192.168.8.99 Bcast:192.168.8.255 Mask:255.255.255.0 > > UP DIFUSIÃ"N MULTICAST MTU:1500 Metric:1 > > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:130 errors:0 dropped:0 overruns:0 carrier:0 > > colisiones:0 txqueuelen:1000 > > RX bytes:0 (0.0 b) TX bytes:5512 (5.3 KB) > > Interrupt:10 > > iwconfig > > eth1 IEEE 802.11b/g ESSID:"fl" Nickname:"Broadcom 4311" > > Mode:Managed Frequency=2.472 GHz Access Point: Invalid > > Bit Rate=1 Mb/s Tx-Power=18 dBm > > RTS thr:off Fragment thr:off > > Encryption key:off > > Link Quality=0/100 Signal level=-256 dBm Noise level=-256 dBm > > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > > Tx excessive retries:0 Invalid misc:0 Missed beacon:0 > > route > > Kernel IP routing table > > Destination Gateway Genmask Flags Metric Ref Use > Iface > > 192.168.7.0 * 255.255.255.0 U 0 0 0 > eth0 > > 192.168.8.0 * 255.255.255.0 U 0 0 0 > eth1 > > 169.254.0.0 * 255.255.0.0 U 1000 0 0 > eth0 > > default 192.168.8.1 0.0.0.0 UG 100 0 0 > eth1 > > > > -------------------------------------- > > si ejecuto wifi-radar radar sin antes ejecutar ifup eth1 desaparece el > > dispositivo eth1 y el comando ifconfig eth1 up no sirve para nada > > (SIOCSIFFLAGS: No existe el dispositivo) > > -------------------------------------- > > si ejecuto wifi-radar radar luego de ejecutar ifup eth1 > > ifconfig > > eth1 Link encap:Ethernet HWaddr 00:1A:73:4E:BB:CD > > inet addr:192.168.8.14 Bcast:192.168.8.255 Mask:255.255.255.0 > > UP DIFUSIÃ"N MULTICAST MTU:1500 Metric:1 > > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > > TX packets:2309 errors:0 dropped:0 overruns:0 carrier:0 > > colisiones:0 txqueuelen:1000 > > RX bytes:0 (0.0 b) TX bytes:98922 (96.6 KB) > > Interrupt:10 > > iwconfig > > eth1 IEEE 802.11b/g ESSID:"fl" Nickname:"fl" > > Mode:Managed Frequency=2.472 GHz Access Point: Invalid > > Bit Rate=1 Mb/s Tx-Power=18 dBm > > RTS thr:off Fragment thr:off > > Encryption key:off > > Link Quality=0/100 Signal level=-256 dBm Noise level=-256 dBm > > Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 > > Tx excessive retries:0 Invalid misc:0 Missed beacon:0 > > route > > Destination Gateway Genmask Flags Metric Ref Use > Iface > > 192.168.7.0 * 255.255.255.0 U 0 0 0 > eth0 > > 192.168.8.0 * 255.255.255.0 U 0 0 0 > eth1 > > 169.254.0.0 * 255.255.0.0 U 1000 0 0 > eth0 > > default 192.168.8.1 0.0.0.0 UG 0 0 0 > eth1 > > > > Me llama la atencion que la métrica sea diferente del default gateway > > entre ifup y la de wifi-radar > > > > Nota: en ninguno de los casos responde ni siquiera al ping. > > > > Saludos. > > -- > > ______________________________ > > Mauro Graziosi > > -- > > Para desuscribirte tenés que visitar la página > > https://listas.linux.org.ar/mailman/listinfo/lugar-gral/ > > > > /* Publica y encontra trabajo relacionado con softlibre en > > http://www.usla.org.ar/modules/jobs/ */ > > > > Si tenés algún inconveniente o consulta escribí a > > mailto:[EMAIL PROTECTED] > > > > > > ---------------------------------------------------------------- > This message was sent using IMP, the Internet Messaging Program. > > > > -- > Para desuscribirte tenés que visitar la página > https://listas.linux.org.ar/mailman/listinfo/lugar-gral/ > > /* Publica y encontra trabajo relacionado con softlibre en > http://www.usla.org.ar/modules/jobs/ */ > > Si tenés algún inconveniente o consulta escribí a mailto:[EMAIL PROTECTED] >
-- Atte: Pablo Nicolás Baratto García Licenciado en Informatica -- Para desuscribirte tenés que visitar la página https://listas.linux.org.ar/mailman/listinfo/lugar-gral/ /* Publica y encontra trabajo relacionado con softlibre en http://www.usla.org.ar/modules/jobs/ */ Si tenés algún inconveniente o consulta escribí a mailto:[EMAIL PROTECTED]
