Dear all,
Some time ago I read something about fretting vihuelas, probably
Bermudo: as I remember, the "best" vihuelas can be fretted with the
same thickness of gut all the way up the neck. Can somebody quote this
source more accurately?
Best,
Sam
On 15 August 2012 11:46, Martyn Hodgson <[1]hodgsonmar...@yahoo.co.uk>
wrote:
Dear Stuart,
Many people nowadays use a quite large diameter first fret
(around 1.00mm or even more on a relatively small [60cm] lute)
but, as
Martin points out, the best record of actual historic fret sizes
is
John Dowland (in Varietie) which suggests significantly thinner
frets -
these allow a lute to be 'set fine' ie minimum distance between
string
and fingerboard at the higher frets, so easing higher fret
fingering.
I try to aim for first fret at 0.90mm on this size of instrument
but,
again as Martin points out, this depends on the set of your
particular
instrument. So that if the neck has pulled up a bit, or even
incorrectly set from the start, you can use almost same diameter
frets
right up the fingerboard (around 0.70mm) - like a modern
'classical'
guitar. But if the neck set is in the same plane as the belly (at
the
bridge) you may well need graduated frets. As said, I aim for a
setting on this size lute which allows from 0.90 (first) down to
around
0.50mm (8th fret).
Thomas Mace also gives some info (again, hurrah Thos.!): 'with a
fine
smooth File, cut the Notches to a convenient depth so that all
your
Strings may lye at an even and equal height, from the
Finger-Board,
which would be about the thickness of a Half-Crown, or a little
more;'. So if you know the thickness of a halfcrown in 1676 you
know
the distance from the underside of the strings to the fingerboard
at
the nut he's advocating and hence you may judge the diameter of
his
ideal first fret.
Finally, Martin raises the matter of double v single loop frets:
in
fact there is no early evidence for the use of single loop frets
with
the noticeable exception, again, of the all-inclusive Thos Mace
who, it
should be noted, when it comes down to describing how to tie a
fret
desribes the usual double loop. You may care to see my paper on
this
very subject in the forthcoming issue of FoMRHI Quarterly.
regards
Martyn
From: Martin Shepherd <[2]mar...@luteshop.co.uk>
Subject: [LUTE] Re: fret gut
To: "Lute List" <[3]lute@cs.dartmouth.edu>
Date: Tuesday, 14 August, 2012, 21:14
Hi Stuart,
It depends on the height of the nut. The first fret has to be as
high
as it can be without buzzing (in normal play, and this is
surprisingly
high), and so on up the neck. This may involve reducing fret sizes
as
one goes "up" the neck, it may not.
Historically Dowland suggested using a fourth course string (about
.75mm?) for the first fret, but he was talking about double frets.
Best wishes,
Martin
14/08/2012 21:01, WALSH STUART wrote:
> Is there a set of standard gauges of fret gut for a typical G
lute,
> 60cms string length?
> And, if so, what are they?
> Stuart
> --
>
>
> To get on or off this list see list information at
> [1][4]http://www.cs.dartmouth.edu/~wbc/lute-admin/index.html
--
References
1. [5]http://www.cs.dartmouth.edu/~wbc/lute-admin/index.html
--
Sam Chapman
Oetlingerstrasse 65
4057 Basel
(0041) 79 530 39 91
--
References
1. mailto:hodgsonmar...@yahoo.co.uk
2. mailto:mar...@luteshop.co.uk
3. mailto:lute@cs.dartmouth.edu
4. http://www.cs.dartmouth.edu/~wbc/lute-admin/index.html
5. http://www.cs.dartmouth.edu/~wbc/lute-admin/index.html
