That code is for Tru64, not Linux. See http://www.m5sim.org/wiki/index.php/Splash_benchmarks.
Steve On Nov 27, 2007 3:38 AM, Panayiotis Petridis <[EMAIL PROTECTED]> wrote: > > btw when i try to build the pthreads folder i get this message: > > make > cc -c -O2 -I. -D_REENTRANT -DPARMACS_INTERNALS > parmacs_support.c > cc -c -O2 -I. -D_REENTRANT -DPARMACS_INTERNALS > parmacs_sync.c > cc -c -O2 -I. -D_REENTRANT -DPARMACS_INTERNALS m5.c > as m5_asm.s -o m5_asm.o > m5_asm.s: Assembler messages: > m5_asm.s:14: Error: unknown pseudo-op: `.ent' > m5_asm.s:15: Error: unknown pseudo-op: `.frame' > m5_asm.s:16: Error: no such instruction: `ldiq $v0,SYS_ x' > m5_asm.s:17: Error: expected comma after "noat" > m5_asm.s:18: Error: invalid character '_' in mnemonic > m5_asm.s:19: Error: expected comma after "at" > make: *** [m5_asm.o] Error 1 > > How did you build this folder of pthreads beacaus obviously i am doing > something wrong. > > Thanks > > > > ________________________________ > > Date: Mon, 26 Nov 2007 21:40:46 -0500 > > From: [EMAIL PROTECTED] > > > To: [email protected] > > Subject: Re: [m5-users] Running SPLASH2 on SE mode > > > > Panayiotis, > > > > I've gotten this error before too. One thing you could check is to make > > sure that the processors parameter (-p) on your FMM command is what you > > think it is. I had mine set to 4 when my simulated system only had 2 > > processors. > > > > Hope this helps. > > > > Julian > > > > On Nov 26, 2007 6:26 PM, Panayiotis Petridis <[EMAIL PROTECTED]> wrote: > > > > Sorry for contacting again the error was solved but now i get this: > > > > command line: build/ALPHA_SE/m5.debug run.py -n4 > > --rootdir=/home/sfin/m5/splash2/codes --benchmark=FMM > > Global frequency set at 1000000000000 ticks per second > > 0: system.remote_gdb.listener: listening for remote gdb #0 on port 7000 > > 0: system.remote_gdb.listener: listening for remote gdb #1 on port 7001 > > 0: system.remote_gdb.listener: listening for remote gdb #2 on port 7002 > > 0: system.remote_gdb.listener: listening for remote gdb #3 on port 7003 > > warn: Entering event queue @ 0. Starting simulation... > > Exiting @ tick 9223372036854775807 because simulate() limit reached > > > > do you have any idea what the problem might be? > > > > Thanks > > > > ---------------------------------------- > >> From: [EMAIL PROTECTED] > >> To: [email protected] > >> Subject: Re: [m5-users] Running SPLASH2 on SE mode > >> Date: Mon, 26 Nov 2007 17:11:00 -0600 > >> > >> Here is an updated version of the splash2 configuration file and it > >> should solve your problem. > >> > >> > >> Ali > >> > > > > _________________________________________________________________ > > Explore the seven wonders of the world > > http://search.msn.com/results.aspx?q=7+wonders+world&mkt=en-US&form=QBRE_______________________________________________ > > m5-users mailing list > > [email protected] > > http://m5sim.org/cgi-bin/mailman/listinfo/m5-users > > > > > > > > -- > > Julian Bui > > [EMAIL PROTECTED] > > _________________________________________________________________ > Explore the seven wonders of the world > http://search.msn.com/results.aspx?q=7+wonders+world&mkt=en-US&form=QBRE_______________________________________________ > m5-users mailing list > [email protected] > http://m5sim.org/cgi-bin/mailman/listinfo/m5-users > _______________________________________________ m5-users mailing list [email protected] http://m5sim.org/cgi-bin/mailman/listinfo/m5-users
