Make sure: * Your stepper driver is installed correctly (it's easy to install them backwards or off-by-one on the pin alignment)
* You are using the proper axis, there are 6 to choose from and not all get driven in the MendelMax config * You have an appropriate power supply connected to the motor power input on the CRAMPS board. There are several different power rails on the CRAMPS (Motor, Bed, Extruder, and Aux) which provides flexibility, but can make it confusing to wire up. On 3/5/2019 11:28 PM, Bradley Turner wrote: > I am working with Jonas on this project as well. I successfully installed > machine kit on the BeagleBone with a CRAMPS cape attached. I was able to > get into the desktop environment of the beaglebone and launch the > machinekit "Mendel Max CRAMPS" setup. I got into the GUI AXIS, and was able > to turn machine on/off trigger the E-steps on/off etc., but when I went to > do a test move of the machine by using the jogging commands in the GUI of > AXIS the stepper motor would not turn. In the software the preview of the > machine would move exactly like it was supposed to but the stepper would > not move. I swapped out the stepper motor to make sure that wasn't the > issue, and it was not. What could be causing this? I tried to scrub through > the .ini and .hal files for stepper driver configuration but was not able > to find it. Also is there a better machinekit config out there for the > CRAMPS board for us with a CNC? I have no problem using the Mendel Max > setup, it is just geared towards a 3D printer, and I wasn't sure if there > would be a better option already configured. > Thank you for any help you can provide. > , > On Thursday, February 21, 2019 at 10:31:53 PM UTC-5, jonas hauptman wrote: >> >> Hi, >> >> We are new to your group and to machine kit but hoping the community might >> have some feedback for us. We are trying to develop a Rotary 4 axis CNC >> router to machine bamboo poles into precise joints. We believe this >> will require six motors and also a scanning function as bamboo poles are >> highly irregular in size, shape, and straightness. Our project goal is to >> democratize CNC rotary machining with a low-cost high-performance machine >> for bamboo. A material that has a huge environmental and >> mechanical upside for both the developed and developing world. >> Presently it is difficult to use it in a high precision fashion and we hope >> to change that. Initially, we planned to use a 3d printer Arduino boards >> and Marlin to control the machine but eventually realized we would have >> trouble independently controlling six motors and true 4 axis machining. We >> have a little experience with LinuxCNC, I built a CNC Router Parts kit and >> outfitted it with a custom electronics bundle that Len from Probotix was >> kind enough to create for me around there standard control system (Unity). >> I am a huge fan of the Probotix machines and controls but we are trying to >> develop a machine that in total costs around $500 to build >> including computer, scanning camera, touch display, completely mechanical, >> electrical and CNC system. Our earlier prototypes used some open >> source components designs and still share some common strategies with >> the Sienci Mill One Kit V3. Realizing that the cost of a full computer and >> control system even on Linux was too expensive and that Arduino with GRBL >> lack the horsepower and software features we need we are trying to develop >> our strategy and prototypes around the Beaglebone with a Cramps Cape. >> >> I am posting hoping to begin to build a community around our project and >> looking for insights of any kind especially around our need of a control >> system for 4 axis and that can support our scanning needs. I have >> attached a series of schematic and photographic summaries of our progress >> and look forward to input from the community. >> >> Best regards, >> >> Jonas Hauptman >> >> >> >> >> >> >> >> >> >> >> >> > -- Charles Steinkuehler [email protected] -- website: http://www.machinekit.io blog: http://blog.machinekit.io github: https://github.com/machinekit --- You received this message because you are subscribed to the Google Groups "Machinekit" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. Visit this group at https://groups.google.com/group/machinekit. For more options, visit https://groups.google.com/d/optout.
