> On Sep 19, 2008, at 5:03 PM, Bryan Blackburn wrote: >> >> >> If you use py25-serial instead, then that 'sudo ln -s ...' above >> would not >> be needed (and in theory, could be a bad idea though sounds like it >> works >> for the serial module). >> >> Both py-serial and py25-serial install the serial module, but the >> former >> installs it with python 2.4 (hence the python2.4 in that path >> above), and >> the latter for python 2.5. Since all of the other modules listed >> are for >> 2.5, using py25-serial should be much simpler as then you won't >> have to >> build/install both 2.4 and 2.5 of python. Especially if you'll >> just be >> linking the one module from 2.4 into 2.5.
On Sep 19, 2008, at 6:44 PM, Ryan Schmidt wrote: > Right. > > Richard, could you please submit feedback to the authors of the > document you read, telling them to update their instructions to use > py25-serial instead of py-serial? You can refer them back to Bryan's > message with this URL if necessary: > > http://lists.macosforge.org/pipermail/macports-users/2008-September/011555.html Ryan, Feedback sent -- see your copy of the email set to the developer, Dan Smith. Now, can someone please advise me as to what I need to do to recover from yesterday's failed installation, including the fix for the "py- serial" problem. Either that, or tell me how to undo what was done yesterday. I am way over my head here, but am willing to learn to get this done, given guidance. Briefly, the failed installation that started this way: > <me>$ sudo port install py25-gtk py-serial py25-xml py25-hashlib and ended this way: > Error: The following dependencies failed to build: py25-cairo py25- > numpy py25-hashlib py25-gobject libxslt > Error: Status 1 encountered during processing. And earlier in the log before the error occurred, it says this: > To fully complete your installation and make python 2.5 the default, > please run > sudo port install python_select > sudo python_select python25 Ignoring the reported error, I ran those two sudo commands with these results: > ---> Fetching python_select > ---> Attempting to fetch select-0.1.tar.gz from > http://svn.macports.org/repository/macports/contrib/select/ > ---> Verifying checksum(s) for python_select > ---> Extracting python_select > ---> Configuring python_select > ---> Building python_select with target all > ---> Staging python_select into destroot > ---> Installing python_select 0.1_4+darwin_9 > ---> Activating python_select 0.1_4+darwin_9 > ---> Cleaning python_select > <me>$ sudo python_select python25 > Selecting version "python25" for python One problem is: I don't know what state this leaves my installation in, and I am not knowledgeable enough to know how to find out. Please advise. For a more complete version of the installation log, see below. Dick Rucker, KM4ML Prior to where the error occurred, a repeating pattern of reports in the log: "Fetching through Activating and Cleaning" indicates that a lot of stuff was installed without apparent error. The following picks up where the trouble began: > ---------------------------------------- > To fully complete your installation and make python 2.5 the default, > please run > > sudo port install python_select > sudo python_select python25 > > ---> Cleaning python25 > ---> Fetching py25-hashlib > ---> Attempting to fetch Python-2.5.2.tar.bz2 from > http://www.python.org/ftp/python/2.5.2/ > ---> Verifying checksum(s) for py25-hashlib > ---> Extracting py25-hashlib > ---> Configuring py25-hashlib > ---> Building py25-hashlib with target build > Error: Target org.macports.build returned: shell command " cd "/opt/ > local/var/macports/build/ > _opt_local_var_macports_sources_rsync > .macports.org_release_ports_python_py25-hashlib/work/Python-2.5.2/ > Modules" && /opt/local/bin/python2.5 setup.py build " returned error 1 > Command output: running build > running build_ext > building '_hashlib' extension > creating build > creating build/temp.macosx-10.3-i386-2.5 > -DNDEBUG -g -fwrapv -O3 -Wall -Wstrict-prototypes -I/opt/local/include > -I/opt/local/Library/Frameworks/Python.framework/Versions/2.5/include/ > python2.5 -c _hashopenssl.c -o build/temp.macosx-10.3-i386-2.5/ > _hashopenssl.o > unable to execute -DNDEBUG: No such file or directory > error: command '-DNDEBUG' failed with exit status 1 > > Error: The following dependencies failed to build: py25-cairo py25- > numpy py25-hashlib py25-gobject libxslt > Error: Status 1 encountered during processing. _______________________________________________ macports-users mailing list [email protected] http://lists.macosforge.org/mailman/listinfo.cgi/macports-users
