> On Dec 4, 2014, at 3:46 PM, Bradley Giesbrecht <[email protected]> wrote: > > > On Nov 27, 2014, at 7:04 AM, Ubence Quevedo <[email protected]> wrote: > >> Hi All, > > Hi from Turlock:) >
Greetings from Merced! >> I'm not sure that this is the right place to post this, but it seems that >> smartmontools that I have installed through port isn't scanning drive when I >> have the appropriate configuration file at /opt/local/etc/smartd.conf >> configured. >> >> Here's the relevant line to run a short scan at 5AM every morning and then a >> long scan at 6AM: >> /dev/disk0 -H -l error -l selftest -f -s (S/../.././05|L/../.././06) -m >> [email protected] >> >> I took a look at the console, and saw the following lines when the scanning >> was supposed to occur: >> Nov 25 05:22:24 Ubences-Intel-iMac.local smartd[152]: Authorization, server >> not available >> Nov 25 05:22:24 Ubences-Intel-iMac.local smartd[152]: Device: /dev/disk0, >> execute Short Self-Test failed. >> Nov 25 06:22:25 Ubences-Intel-iMac.local smartd[152]: Device: /dev/disk0, >> execute Long Self-Test failed. >> >> What stands out to me is the first line "Authorization, server not >> available". >> >> I've tried looking for info on this particular output, but I can't find >> anything to trace back to how this is occurring? > > Can you run smartctl successfully? > sudo smartctl -P show /dev/disk0 > sudo smartctl -t short /dev/disk0 > sudo smartctl -a /dev/disk0 > I can run all of those, and I’ve never had to sudo them: Ubences-Intel-iMac:~ uquevedo$ smartctl -P show /dev/disk0 smartctl 6.2 2013-07-26 r3841 [x86_64-apple-darwin14.0.0] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org Drive found in smartmontools Database. Drive identity strings: MODEL: WDC WD1002FAEX-00Y9A0 FIRMWARE: 05.01D05 match smartmontools Drive Database entry: MODEL REGEXP: WDC WD(5002AAL|(64|75)02AAE|((10|15|20)02|4001)FAE)X-.* FIRMWARE REGEXP: .* MODEL FAMILY: Western Digital Caviar Black ATTRIBUTE OPTIONS: None preset; no -v options are required. Ubences-Intel-iMac:~ uquevedo$ smartctl -t short /dev/disk0 smartctl 6.2 2013-07-26 r3841 [x86_64-apple-darwin14.0.0] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF OFFLINE IMMEDIATE AND SELF-TEST SECTION === Sending command: "Execute SMART Short self-test routine immediately in off-line mode". Drive command "Execute SMART Short self-test routine immediately in off-line mode" successful. Testing has begun. Please wait 2 minutes for test to complete. Test will complete after Thu Dec 4 17:00:29 2014 Use smartctl -X to abort test. Ubences-Intel-iMac:~ uquevedo$ smartctl -a /dev/disk0 smartctl 6.2 2013-07-26 r3841 [x86_64-apple-darwin14.0.0] (local build) Copyright (C) 2002-13, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Caviar Black Device Model: WDC WD1002FAEX-00Y9A0 Serial Number: [Hiding this on purpose] LU WWN Device Id: 5 0014ee 2064339e8 Firmware Version: 05.01D05 User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS (minor revision not indicated) SATA Version is: SATA 2.6, 6.0 Gb/s (current: 3.0 Gb/s) Local Time is: Thu Dec 4 17:03:58 2014 PST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x85) Offline data collection activity was aborted by an interrupting command from host. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (16860) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 174) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 13 3 Spin_Up_Time 0x0027 171 170 021 Pre-fail Always - 4433 4 Start_Stop_Count 0x0032 076 076 000 Old_age Always - 24328 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 100 253 000 Old_age Always - 0 9 Power_On_Hours 0x0032 094 094 000 Old_age Always - 5066 10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 079 079 000 Old_age Always - 21823 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 21 193 Load_Cycle_Count 0x0032 192 192 000 Old_age Always - 24306 194 Temperature_Celsius 0x0022 107 081 000 Old_age Always - 40 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 1 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short offline Completed without error 00% 5066 - # 2 Extended offline Completed without error 00% 4673 - # 3 Extended offline Completed without error 00% 4080 - # 4 Short offline Completed without error 00% 2987 - # 5 Extended offline Aborted by host 80% 2985 - # 6 Short offline Completed without error 00% 2982 - # 7 Short offline Completed without error 00% 2975 - # 8 Short offline Aborted by host 90% 2962 - # 9 Short offline Completed without error 00% 2960 - #10 Short offline Completed without error 00% 2957 - #11 Short offline Completed without error 00% 2956 - #12 Short offline Completed without error 00% 2950 - #13 Short offline Completed without error 00% 2948 - #14 Short offline Completed without error 00% 2946 - #15 Short offline Completed without error 00% 2944 - #16 Short offline Completed without error 00% 2941 - #17 Short offline Completed without error 00% 2939 - #18 Short offline Completed without error 00% 2934 - #19 Short offline Completed without error 00% 2933 - #20 Short offline Completed without error 00% 2929 - #21 Short offline Completed without error 00% 2927 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. As you can see from the Self-test log, the configuration file was all working up to a point and then just stopped. -Ubence > > Regards, > Bradley Giesbrecht (pixilla) >
_______________________________________________ macports-users mailing list [email protected] https://lists.macosforge.org/mailman/listinfo/macports-users
