#1960: a question about using wep with hostapd ----------------------------+----------------------------------------------- Reporter: bryant_li | Type: defect Status: new | Priority: minor Component: madwifi: other | Version: v0.9.4 Keywords: hostap | Patch_attached: 0 ----------------------------+----------------------------------------------- My harware environment is Atheros R5212 and an 1000m ehternet card,software is centos4.2(2.6.9 kernel)+madwifi0.9.4+hostapd 0.5.10
I want to use wep encryption. 1.Only use madwifi.It works fine. First,I install madwifi correctly and I input commands below: modprobe ath_pci wlanconfig ath0 destroy wlanconfig ath0 create wlandev wifi0 wlanmode ap iwconfig ath0 essid "test" key 1111-2222-33 ifconfig ath0 10.0.0.1 netmask 255.255.255.0 I use iptables to implement NAT. In a terminal,I make the correct configration,and it could ping remote web site successful. 2.use Hostapd,it doesn't work. Here is my hostpad.conf file: interface=ath0 driver=madwifi debug=0 dump_file=/tmp/hostapd.dump ctrl_interface=/var/run/hostapd ctrl_interface_group=0 ssid=test auth_algs=3 ignore_broadcast_ssid=0 wep_default_key=1 wep_key1=1111222233 bridge_packets=1 I run hostapd -d hostapd.conf The screen shot is : Configuration file: madwifi.conf madwifi_set_iface_flags: dev_up=0 madwifi_set_privacy: enabled=0 BSS count 1, BSSID mask ff:ff:ff:ff:ff:ff (0 bits) ath0: IEEE 802.11 Fetching hardware channel/rate support not supported. Flushing old station entries madwifi_sta_deauth: addr=ff:ff:ff:ff:ff:ff reason_code=3 madwifi_sta_deauth: Failed to deauth STA (addr ff:ff:ff:ff:ff:ff reason 3) Could not connect to kernel driver. Deauthenticate all stations madwifi_set_privacy: enabled=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=0 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=1 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=2 madwifi_del_key: addr=00:00:00:00:00:00 key_idx=3 madwifi_set_key: alg=WEP addr=00:00:00:00:00:00 key_idx=1 madwifi_set_privacy: enabled=1 Using interface ath0 with hwaddr 00:1d:0f:30:4d:bb and ssid 'test' ath0: Setup of interface done. Wireless event: cmd=0x8c03 len=20 ath0: STA 00:1d:60:b1:af:8b IEEE 802.11: associated Wireless event: cmd=0x8c02 len=101 Custom wireless event: 'STA-TRAFFIC-STAT mac=00:1d:60:b1:af:8b rx_packets=6 rx_bytes=465 tx_packets=0 tx_bytes=0 ' Wireless event: cmd=0x8c04 len=20 ath0: STA 00:1d:60:b1:af:8b IEEE 802.11: disassociated Wireless event: cmd=0x8c03 len=20 ath0: STA 00:1d:60:b1:af:8b IEEE 802.11: associated New STA As you see ,the terminl can't associated as normal,it disassociated at soon as associated.If I run dhcpd on the server ,the clients will not able to obtain an IP. I don,t know what's the problem.Could anyone help me?Thanks a lot. -- Ticket URL: <http://madwifi.org/ticket/1960> madwifi.org <http://madwifi.org/> Multiband Atheros Driver for Wireless Fidelity ------------------------------------------------------------------------- This SF.net email is sponsored by: Microsoft Defy all challenges. Microsoft(R) Visual Studio 2008. http://clk.atdmt.com/MRT/go/vse0120000070mrt/direct/01/ _______________________________________________ Madwifi-tickets mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/madwifi-tickets
