#2414: cannot set the tx power over 20 dBm, wrong contry code
--------------------------------+-------------------------------------------
Reporter: krbjh...@online.no | Type: defect
Status: new | Priority: minor
Component: madwifi: other | Version:
Keywords: | Patch_attached: 0
Pending: 0 |
--------------------------------+-------------------------------------------
My pc is a Panasonic CF-20
My card is : ENGENIUS EMP-8602+S 802.11a/b/g 600mW ( 28 dbm )
I run Kubuntu 10.4
iwconfig outputs:
wlan0 IEEE 802.11abg ESSIDff/any
Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm
Retry long limit:7 RTS thrff Fragment thrff
Encryption keyff
Power Managementff
iwconfig wlan0 txpower 600mw
Error for wireless request "Set Tx Power" (8B26) :
SET failed on device wlan0 ; Invalid argument.
i have tried:
iwpriv wlan0 highpower 1
it puts out : wlan0 no private ioctls.
iwlist wlan0 txpower
wlan0 unknown transmit-power information.
Current Tx-Power=20 dBm (100 mW)
iw list
Wiphy phy0
Band 1:
Frequencies:
* 2412 MHz [1] (20.0 dBm)
* 2417 MHz [2] (20.0 dBm)
* 2422 MHz [3] (20.0 dBm)
* 2427 MHz [4] (20.0 dBm)
* 2432 MHz [5] (20.0 dBm)
* 2437 MHz [6] (20.0 dBm)
* 2442 MHz [7] (20.0 dBm)
* 2447 MHz [8] (20.0 dBm)
* 2452 MHz [9] (20.0 dBm)
* 2457 MHz [10] (20.0 dBm)
* 2462 MHz [11] (20.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
Bitrates (non-HT):
* 1.0 Mbps
* 2.0 Mbps (short preamble supported)
* 5.5 Mbps (short preamble supported)
* 11.0 Mbps (short preamble supported)
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
Band 2:
Frequencies:
* 5180 MHz [36] (20.0 dBm) (passive scanning, no
IBSS)
* 5200 MHz [40] (20.0 dBm) (passive scanning, no
IBSS)
* 5220 MHz [44] (20.0 dBm) (passive scanning, no
IBSS)
* 5240 MHz [48] (20.0 dBm) (passive scanning, no
IBSS)
* 5260 MHz [52] (disabled)
* 5280 MHz [56] (disabled)
* 5300 MHz [60] (disabled)
* 5320 MHz [64] (disabled)
* 5500 MHz [100] (disabled)
* 5520 MHz [104] (disabled)
* 5540 MHz [108] (disabled)
* 5560 MHz [112] (disabled)
* 5580 MHz [116] (disabled)
* 5600 MHz [120] (disabled)
* 5620 MHz [124] (disabled)
* 5640 MHz [128] (disabled)
* 5660 MHz [132] (disabled)
* 5680 MHz [136] (disabled)
* 5700 MHz [140] (disabled)
* 5745 MHz [149] (20.0 dBm) (passive scanning, no
IBSS)
* 5765 MHz [153] (20.0 dBm) (passive scanning, no
IBSS)
* 5785 MHz [157] (20.0 dBm) (passive scanning, no
IBSS)
* 5805 MHz [161] (20.0 dBm) (passive scanning, no
IBSS)
* 5825 MHz [165] (20.0 dBm) (passive scanning, no
IBSS)
Bitrates (non-HT):
* 6.0 Mbps
* 9.0 Mbps
* 12.0 Mbps
* 18.0 Mbps
* 24.0 Mbps
* 36.0 Mbps
* 48.0 Mbps
* 54.0 Mbps
max # scan SSIDs: 4
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
Supported commands:
* new_interface
* set_interface
* new_key
* new_beacon
* new_station
* new_mpath
* set_mesh_params
* set_bss
* authenticate
* associate
* deauthenticate
* disassociate
* join_ibss
* set_wiphy_netns
* connect
* disconnect
dmesg output:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 2.6.32-21-generic (bui...@rothera) (gcc
version 4.4.3 (Ubuntu 4.4.3-4ubuntu5) ) #32-Ubuntu SMP Fri Apr 16 08:10:02
UTC 2010 (Ubuntu 2.6.32-21.32-generic 2.6.32.11+drm33.2)
-snip-
[ 0.056533] PCI: PCI BIOS revision 2.10 entry at 0xfd952, last bus=4
[ 21.833798] ppdev: user-space parallel port driver
[ 21.834691] cfg80211: Calling CRDA to update world regulatory domain
[ 21.949546] type=1505 audit(1278500804.961:2):
operation="profile_load" pid=578 name="/sbin/dhclient3"
[ 21.950408] type=1505 audit(1278500804.961:3):
operation="profile_load" pid=578 name="/usr/lib/NetworkManager/nm-dhcp-
client.action"
[ 21.950877] type=1505 audit(1278500804.961:4):
operation="profile_load" pid=578 name="/usr/lib/connman/scripts/dhclient-
script"
[ 21.972709] yenta_cardbus 0000:02:00.0: ISA IRQ mask 0x0c38, PCI irq 9
[ 21.972715] yenta_cardbus 0000:02:00.0: Socket status: 30000006
[ 21.972725] yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge I/O
window: 0x3000 - 0x3fff
[ 21.972731] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x3000-0x3fff: clean.
[ 21.973039] yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge
Memory window: 0xe0200000 - 0xe02fffff
[ 21.973044] yenta_cardbus 0000:02:00.0: pcmcia: parent PCI bridge
Memory window: 0x40000000 - 0x47ffffff
[ 21.981017] ath5k 0000:02:01.0: PCI INT A -> Link[LNKD] -> GSI 9
(level, low) -> IRQ 9
[ 21.981074] ath5k 0000:02:01.0: registered as 'phy0'
[ 22.533189] input: PS/2 Touchpad as
/devices/platform/i8042/serio1/input/input8
[ 22.558838] input: LBPS/2 Fujitsu Lifebook TouchScreen as
/devices/platform/i8042/serio1/input/input9
[ 22.730771] Intel ICH 0000:00:1f.5: PCI INT B -> Link[LNKB] -> GSI 9
(level, low) -> IRQ 9
[ 22.730810] Intel ICH 0000:00:1f.5: setting latency timer to 64
[ 22.819861] ath: EEPROM regdomain: 0x37
[ 22.819865] ath: EEPROM indicates we should expect a direct regpair map
[ 22.819870] ath: Country alpha2 being used: AT («- wrong contry code,
NO is the correct one)
[ 22.819872] ath: Regpair used: 0x37
[ 22.866432] phy0: Selected rate control algorithm 'minstrel'
[ 22.867378] ath5k phy0: Atheros AR5413 chip found (MAC: 0xa4, PHY:
0x61)
[ 22.867751] cfg80211: Calling CRDA for country: AT ( what is going on
here, i am in NO ! )
[ 22.867812] yenta_cardbus 0000:02:00.1: CardBus bridge found
[10f7:8338]
[ 22.960900] type=1505 audit(1278500805.973:5):
operation="profile_replace" pid=737 name="/sbin/dhclient3"
[ 22.961766] type=1505 audit(1278500805.973:6):
operation="profile_replace" pid=737 name="/usr/lib/NetworkManager/nm-dhcp-
client.action"
[ 22.962240] type=1505 audit(1278500805.973:7):
operation="profile_replace" pid=737 name="/usr/lib/connman/scripts
/dhclient-script"
[ 22.972992] type=1505 audit(1278500805.985:8):
operation="profile_load" pid=741 name="/usr/lib/cups/backend/cups-pdf"
[ 22.974035] type=1505 audit(1278500805.985:9):
operation="profile_load" pid=741 name="/usr/sbin/cupsd"
[ 22.977968] type=1505 audit(1278500805.989:10):
operation="profile_load" pid=743 name="/usr/sbin/mysqld-akonadi"
[ 22.980062] type=1505 audit(1278500805.993:11):
operation="profile_load" pid=744 name="/usr/sbin/tcpdump"
[ 22.992700] yenta_cardbus 0000:02:00.1: ISA IRQ mask 0x0c38, PCI irq 9
[ 22.992706] yenta_cardbus 0000:02:00.1: Socket status: 30000006
[ 22.992713] pci_bus 0000:02: Raising subordinate bus# of parent bus
(#02) from #04 to #07
[ 22.992727] yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge I/O
window: 0x3000 - 0x3fff
[ 22.992732] pcmcia_socket pcmcia_socket1: cs: IO port probe
0x3000-0x3fff: clean.
[ 22.993040] yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge
Memory window: 0xe0200000 - 0xe02fffff
[ 22.993045] yenta_cardbus 0000:02:00.1: pcmcia: parent PCI bridge
Memory window: 0x40000000 - 0x47ffffff
[ 23.105159] pcmcia_socket pcmcia_socket1: cs: IO port probe
0x100-0x3af: clean.
[ 23.106784] pcmcia_socket pcmcia_socket1: cs: IO port probe
0x3e0-0x4ff: clean.
[ 23.107476] pcmcia_socket pcmcia_socket1: cs: IO port probe
0x820-0x8ff: clean.
[ 23.108446] pcmcia_socket pcmcia_socket1: cs: IO port probe
0xc00-0xcf7: clean.
[ 23.109245] pcmcia_socket pcmcia_socket1: cs: IO port probe
0xa00-0xaff: clean.
[ 23.153025] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.155578] eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
[ 23.601506] intel8x0_measure_ac97_clock: measured 64844 usecs (3122
samples)
[ 23.601513] intel8x0: clocking to 48000
[ 23.617631] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x100-0x3af: clean.
[ 23.619256] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x3e0-0x4ff: clean.
[ 23.619948] pcmcia_socket pcmcia_socket0: cs: IO port probe
0x820-0x8ff: clean.
[ 23.630698] pcmcia_socket pcmcia_socket0: cs: IO port probe
0xc00-0xcf7: clean.
[ 23.631495] pcmcia_socket pcmcia_socket0: cs: IO port probe
0xa00-0xaff: clean.
[ 33.288046] eth0: no IPv6 routers present
[ 808.274478] device wlan0 entered promiscuous mode
[ 808.279419] device wlan0mon entered promiscuous mode
[ 3405.618846] ath5k phy0: unsupported jumbo
--
Ticket URL: <http://madwifi-project.org/ticket/2414>
madwifi-project.org <http://madwifi-project.org/>
Multiband Atheros Driver for Wireless Fidelity
------------------------------------------------------------------------------
This SF.net email is sponsored by Sprint
What will you do first with EVO, the first 4G phone?
Visit sprint.com/first -- http://p.sf.net/sfu/sprint-com-first
_______________________________________________
Madwifi-tickets mailing list
Madwifi-tickets@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/madwifi-tickets
