I think you should try saving it as a MapInfo tab Peter Horsb�ll M�ller GIS Developer Geographical Information & IT COWI A/S Odensevej 95 DK-5260 Odense S. Denmark Tel +45 6311 4900 Direct +45 6311 4908 Mob +45 5156 1045 Fax +45 6311 4949 E-mail [EMAIL PROTECTED] http://www.cowi.dk/gis
Sidste frist for tilmelding til MapInfo Konferencen er den 6. august 2004. Tilmelding samt yderligere information kan ses p�: http://www.cowi.dk/GIS -----Original Message----- From: Juha Hiltula [mailto:[EMAIL PROTECTED] Sent: Thursday, July 29, 2004 2:58 PM To: Vinesh Govind Cc: [EMAIL PROTECTED] Subject: RE: MI-L Vertical Mapper Query Vinesh, Did that solve your problem? I had earlier same error message though in different situation. I was about to convert polylines to points in Vertical Mapper and could�t do that because of error 503. Anyway you could try save your file to Microsoft Access Database (in save copy as-catalogue choose save as type:...) and retry with this new copy. That didn�t solve problem in my case, but anyway dropped error message value to 306! Juha Hiltula Oulu, Finland -- On Thu, 29 Jul 2004, Peter Horsb�ll M�ller wrote: > This might happen if the source isn't placed in a MapInfo base table, > but fore instance in an Excel Worksheet etc. > > He could try using the File > Save as... and save the table to a new > file and then retyr with this copy > > Peter Horsb�ll M�ller > GIS Developer > Geographical Information & IT > > COWI A/S > Odensevej 95 > DK-5260 Odense S. > Denmark > > Tel +45 6311 4900 > Direct +45 6311 4908 > Mob +45 5156 1045 > Fax +45 6311 4949 > E-mail [EMAIL PROTECTED] > http://www.cowi.dk/gis > > Sidste frist for tilmelding til MapInfo Konferencen er den 6. august > 2004. Tilmelding samt yderligere information kan ses p�: > http://www.cowi.dk/GIS > > > -----Original Message----- > From: Vinesh Govind [mailto:[EMAIL PROTECTED] > Sent: Thursday, July 29, 2004 8:53 AM > To: '[EMAIL PROTECTED]' > Subject: MI-L Vertical Mapper Query > > > A colleague in our Department is is using the Vertical Mapper wizard > to Create a Grid using the Interpolation method. When he clicks > Triangulation with Smoothing and then Next.........he then loads the > table and selects the column he would like to create the Grid on. When > he clicks next the following error appears: > > Error in MapInfo File Access Library > Extended Error Value: 503 > > Anyone know what this means and how we can rectify. > > Thanks. > > > > Vinesh Govind > Information Management Team > Pen Lloyd Building - Room G48 > Chief Executives Department > Leicestershire County Council > (T) (0116) 265 7321 > http://www.leics.gov.uk > > > > ______________________________________________________________________ > _ > The contents of this message do not necessarily represent the > opinions, views, policy or procedures of Leicestershire County Council. > > > --------------------------------------------------------------------- > List hosting provided by Directions Magazine | www.directionsmag.com | > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: > [EMAIL PROTECTED] > Message number: 12791 > > --------------------------------------------------------------------- List hosting provided by Directions Magazine | www.directionsmag.com | To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] Message number: 12796 --------------------------------------------------------------------- List hosting provided by Directions Magazine | www.directionsmag.com | To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED] Message number: 12797
