We were going to buy new printers but then Meditech referred us to the attached article and it worked for our HP4200 PRINTERS
Looks like the 4200 is the lowest model that has been found to work but review it and see if you printer has the same menu setting options as these.... Marie Johnson Financial Application Support /Report Writer Northern Berkshire Health Systems 71 Hospital Avenue North Adams, Ma 01247 Phone: 413-664-5253 Fax: 413-664-5322. email: [EMAIL PROTECTED]
--- Begin Message ---So is everyone going out and buying new printers for the UB04? Ours are older models, without the edge-to-edge printing... ??? Cindy Bodnar-Anderson Senior Programmer/Analyst IS, Regional Health Rapid City SD 57701 -----Original Message----- From: Koppmann, Lisa Sent: Wednesday, May 02, 2007 11:50 AM To: Woodson, Wilma Cc: Bodnar-Anderson, Cindy Subject: RE: [MEDITECH-L] UB04 On HP 4250 Laserjet The problem is our print is not an edge-to-edge printer so we can't adjust the X or Y printing settings and all of these from the L have newer printers. We need help with our printers purchased 7 years ago. Hewlett Packard LaserJet # 4050N -----Original Message----- From: Woodson, Wilma Sent: Wednesday, May 02, 2007 11:22 AM To: Koppmann, Lisa Subject: FW: [MEDITECH-L] UB04 On HP 4250 Laserjet Lisa maybe try this one -see below -----Original Message----- From: Bodnar-Anderson, Cindy Sent: Wednesday, May 02, 2007 11:19 AM To: Woodson, Wilma Subject: FW: [MEDITECH-L] UB04 On HP 4250 Laserjet fyi Cindy -----Original Message----- From: Gary Ring [mailto:[EMAIL PROTECTED] Sent: Tuesday, May 01, 2007 8:47 AM To: [email protected] Subject: [MEDITECH-L] UB04 On HP 4250 Laserjet Well, I have some good news (and hopefully my last post on the topic). After many tedious and excruiating hours of testing, I think I have found the settings that will work. The keys to getting this to work are: 1. First, finding the CPI settings that will allow ALL characters on the line to print. 2. Then, finding the proper horizontal edge-to-edge setting that aligns the form correctly. By no means is the form perfect. Unlike Meditech's programming for the UB92, which they did a very good job on and is almost flawless, Meditech's programming of the UB04 has left a lot to be desired; in fact, I would be embarrassed to send this form out to payers with the way that some of the fields are lined-up within the blocks. But it DOES print all of the characters, and for the most part, the characters that don't fit nicely within the blocks are probably not critical data fields. Here are the settings that I have found work the best: ELF: CPI: 10.12 (this is the key; it is the smallest value that allows all characters on the line to print) Left Margin: 0.20 LPI: 6 Top Margin: 0.095 HP 4250 Printer Quality: X1: -4 Y: 0 Good luck, everyone. Gary J. Ring Strategic Resource Group, Inc. 11 Jones Road, Peabody, MA 01960 978-807-1573 ***Note: The information contained in this message, including any attachments, may be privileged, confidential, and protected from disclosure. If the reader of this message is not the intended recipient, or an employee or agent responsible for delivering this message to the intended recipient, you are hereby notified that any dissemination, distribution or copying of this communication is strictly prohibited. If you have received this communication in error, please notify the Sender immediately by a "reply to sender only" message and destroy all electronic or paper copies of the communication, including any attachments.=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*= To subscribe or unsubscribe to the meditech-l, visit MTUsers.NET. To check the status of the meditech-l, visit MTUsers.NET. For help, email [EMAIL PROTECTED] Visit the MTUsers WikiPedia at MTUsers.NET/mwiki ______________________________________ meditech-l mailing list [email protected] http://mtusers.com/mailman/listinfo/meditech-l
--- End Message ---
Meditech KB article 27503.htm
Description: Binary data
=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*=*= To subscribe or unsubscribe to the meditech-l, visit MTUsers.NET. To check the status of the meditech-l, visit MTUsers.NET. For help, email [EMAIL PROTECTED] Visit the MTUsers WikiPedia at MTUsers.NET/mwiki ______________________________________ meditech-l mailing list [email protected] http://mtusers.com/mailman/listinfo/meditech-l
