I was looking thru some catalogs today at the 200b disc and hilux brake pads and got some prices. Your right, there is 3 types of 200b disc's and theres about 20 different types of brake pad for the hilux. So i got home and pulled apart these stanza struts and did some measurments. The stub axle is close to 124mm long, inner bearing width of 32mm and outer bearing width of 19mm. Are these right?? And the distance between the caliper bolts is exactly 3.5". Will the hilux calipers bolt on?? I also found what i think is a date on the strut. It says 26-11-80. So mabye i do have the wrong strut?? Scott Davo -----Original Message----- From: Terry & Heather <[EMAIL PROTECTED]> To: [EMAIL PROTECTED] <[EMAIL PROTECTED]> Date: Saturday, 19 August, 2000 2:37 Subject: RE: Stanza Suttees in 1200.... >There are three types of 200B discs & callipers and the Hilux callipers only >bolt up to the earlier 10/77 - 7/79 10" Girlock & Sumitomo disc that have >48mm hub height (so I'm told as I've never done it to find out fer sure). >The later Australian Girlocks are only 9.6" and have a 43.mm hub and use >DB1091 Pads. > >regards >Terry > >-----Original Message----- >From: [EMAIL PROTECTED] >[mailto:[EMAIL PROTECTED]]On Behalf Of Davidson >Sent: Thursday, 17 August 2000 7:29 PM >To: [EMAIL PROTECTED] >Subject: Re: Stanza Stuts in 1200.... > > >I was going to get some new disc's for it anyhow. So 200b disc's are 9.5" >right. And then these hilux 4spots can be bolted on right. Sounds like a >good combo to me. Thanx again. > >Scott >Davo > >-----Original Message----- >From: cp <[EMAIL PROTECTED]> >To: [EMAIL PROTECTED] <[EMAIL PROTECTED]> >Date: Wednesday, 16 August, 2000 19:17 >Subject: Re: Stanza Stuts in 1200.... > > >>200b struts are very similar to stanza apart from the spring size. The >only >>difference in brakes is the disc size (1" bigger). You can actually swap >>the hub/disc and caliper from the 200b on to the stanza strut for that >>little bit extra... >> >>Chris P >> >> >>-----Original Message----- >>From: Davidson <[EMAIL PROTECTED]> >>To: [EMAIL PROTECTED] <[EMAIL PROTECTED]> >>Date: Wednesday, 16 August 2000 18:59 >>Subject: Re: Stanza Stuts in 1200.... >> >> >>>Thanks Chris, >>> >>>I have good idea at what i am going to do now. And still have my options >>>open with the 200b struts. For now i will get the staza struts in and see >>>what its like. >>> >>>Scott >>>Davo >>> >>>-----Original Message----- >>>From: cp <[EMAIL PROTECTED]> >>>To: [EMAIL PROTECTED] <[EMAIL PROTECTED]> >>>Date: Tuesday, 15 August, 2000 20:20 >>>Subject: Re: Stanza Stuts in 1200.... >>> >>> >>>>been there done that. >>>> >>>>Stanza struts fit but you need to drill out the holes on the strut top a >>>>little as the bolts a slightly larger...(think this is right but it may >>>have >>>>been when i was using 1600 tops) >>>> >>>>You need stanza lower arms, ball joints and steering arms. A 120y sway >bar >>>>is also good as there thicker.. >>>> >>>> >>>>should then bolt in however. I did this swap onto my 1200 ute and found >>>the >>>>stanza struts to be very tall....Taller than 1600's ones for that >matter.. >>>>I cut the spring down to they say at normal 1200 height but that left me >>>>with 2" of travel as the shock bottomed out. >>>> >>>>I would recommend getting shorter inserts...say from a 280zx or 240k and >>>>shortening the whole strut assembly if you want to get a reasonably low >>>ride >>>>height.. >>>> >>>>I also offset the tops it get more negitive camber.... >>>> >>>>Give me a yell if you need more info... >>>> >>>>Chris P >>>> >>>> >>>> >>>> >>>>-----Original Message----- >>>>From: Davidson <[EMAIL PROTECTED]> >>>>To: [EMAIL PROTECTED] <[EMAIL PROTECTED]> >>>>Date: Tuesday, 15 August 2000 19:45 >>>>Subject: Stanza Stuts in 1200.... >>>> >>>> >>>>>I have some old Stanza struts and was hoping to fit them to my 1200. >How >>>>do >>>>>i know if there the later model struts?? (1980+). I know i need the >>>stanza >>>>>lower control arms and the castor rods. Is that all or am i missing >>>>>somthing?? All the steering arms connect straight up right?? And the >>sway >>>>>bar connects straight up aswell?? >>>>> >>>>>Im trying to get everything ready first before i start pulling the >struts >>>>>out. I dont want to be half way thru it only to find i need some bits >and >>>>>peices. Any help is great :-) >>>>> >>>>>Scott >>>>>Davo >>>>> >>>> >>> >>> >> > > > --membersozdat------------------------------------------------------- OZDAT Mailing List Please Note:- Send (un)subscribe requests to [EMAIL PROTECTED] Send submissions to [EMAIL PROTECTED] No unauthorised redistribution of this email http://www.ozdat.com/ozdatonline/index.htm http://www.ozdat.com/ozdatonline/listindex.html http://www.mail-archive.com/[email protected]/ ---------------------------------------------------------------------
