No,
If you imagine the boot floor extended through to the out side of the rear
quarter panel that's what you get.  Basically it starts half way down the
rear of the wheel arch and goes to just below the taillight hight at the
back.
----- Original Message -----
From: "Leighton" <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Tuesday, 12 March 2002 23:39 PM
Subject: Re: ozdat ad...info.


> is that the rear quarter like from the rear door to the rear of the car???
> the top section
>
> thanx
> Leighton
> ----- Original Message -----
> From: "Richard Clough" <[EMAIL PROTECTED]>
> To: <[EMAIL PROTECTED]>
> Sent: Tuesday, March 12, 2002 11:00 PM
> Subject: Re: ozdat ad...info.
>
>
> > You can buy the rust repair sections for the rear quarters from the
Datsun
> > 1600 workshop in Bayswater. $150 each side I think. (See the trade
section
> > on the Ozdat Website for address/contact info. These panels will fix all
> > outer rear quarter rust up to the boot floor level.  He also has sill
> > sections for $22 a side.
> >
> > ----- Original Message -----
> > From: "Greg West" <[EMAIL PROTECTED]>
> > To: <[EMAIL PROTECTED]>
> > Sent: Monday, 11 March 2002 23:58 PM
> > Subject: Re: ozdat ad...info.
> >
> >
> > > Hi Daniel,
> > >
> > > pretty much each corner of the floor pan where it meets the sill needs
> > some
> > > work. I think its a case of the previous owner letting the rubbers go
to
> > > shit and then the water getting into the carpet etc etc. Front
passenger
> > > side is the worst of it, probably 20cm x 10cm hole there against the
> sill.
> > > Theres also rust in the rear quarters that needs repair too. In my
other
> > > 1600 I have rust in the rear quarters too, anyone know of any
available
> > > anywhere ?
> > >
> > > By the way Daniel, what are you studying at uq? Im 3rd year info tech
> this
> > > semester. Do you own the metallic blue 1600 ive seen around at uni?
> > >
> > > Cheers,
> > > Greg
> > >
> > > ----- Original Message -----
> > > From: "Daniel Kroehn" <[EMAIL PROTECTED]>
> > > To: <[EMAIL PROTECTED]>
> > > Sent: Monday, March 11, 2002 7:07 PM
> > > Subject: Re: ozdat ad...info.
> > >
> > >
> > > > I saw that ad in the trader.  Just our of interest, how much rust
was
> in
> > > the
> > > > body of the car and where abouts?
> > > >
> > > > Daniel Kroehn
> > > >
> > > > ----- Original Message -----
> > > > From: <[EMAIL PROTECTED]>
> > > > To: <[EMAIL PROTECTED]>
> > > > Sent: Monday, March 11, 2002 6:33 PM
> > > > Subject: ozdat ad...info.
> > > >
> > > >
> > > > > L20B + gearbox +_exhayst + running gear If I dont sell my complete
> > 1600
> > > > > this week I will be wrecking it. I want to sell the engine &
> > drivetrain
> > > > > complete. L20B engine, mild cam, extractors, 3" exhaust system,
vac
> > > tested
> > > > > & recoed head (done 0km), FJ20DET gearbox mated to the l20b, 240K
> > diff,
> > > > > good radiator no leaks, basically the complete drivetrain + long
> > motor.
> > > > > Motor starts first time, runs well & doesnt blow any smoke Will be
> > > asking
> > > > > $500 for the lot
> > > > > Price: $500  Location: South Brisbane
> > > > > Contact: Greg
> > > > >
> > > > > Hiyas, Im looking at buying all this gear....anyone know anything
> > about
> > > it
> > > > > before i hand my cash over? I went back over the older ads and
> spotted
> > > > some
> > > > > that couldve been this setup, but listed different box and a stock
> > > > > engine... its not that i dont trust him, im just very wary. Anyone
> > know
> > > > > Greg, know the gear? Any info (off list) appreciated.
> > > > >
> > > > > Cheers,
> > > > > Brodie.
> > > > >
> > > >
> > > >
> > >
> > >
> >
> >
>
>

--membersozdat-------------------------------------------------------
OZDAT Mailing List   Please Note:-
Send (un)subscribe requests to  [EMAIL PROTECTED]
Send  submissions to  [EMAIL PROTECTED]
No unauthorised redistribution of this email
http://www.ozdat.com/ozdatonline/index.htm
http://www.ozdat.com/ozdatonline/listindex.html
http://www.mail-archive.com/[email protected]/
---------------------------------------------------------------------

Reply via email to