regards, Hari Prasad S R 7418234575
---------- Forwarded message ---------- From: hari prasad <[email protected]> Date: Wed, Jun 25, 2014 at 3:56 PM Subject: Re: [meta-freescale] t4240 offloading applications To: "[email protected]" <[email protected]> I have tried that as well but the problem is I cant find offloading drivers in the /dev/ folder of the rootfs regards, Hari Prasad S R 7418234575 On Wed, Jun 25, 2014 at 3:49 PM, [email protected] < [email protected]> wrote: > Please use uImge-t4240qds-usdpaa.dtb instead of uImage-t4240qds.dtb. > > > > > > Best Regards, > > > > Zhenhua > > > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *hari prasad > *Sent:* Wednesday, June 25, 2014 1:26 AM > *To:* Luo Zhenhua-B19537 > *Cc:* [email protected] > *Subject:* Re: [meta-freescale] t4240 offloading applications > > > > uboot environment variables: > > > U-Boot 2013.01 (May 25 2014 - 14:54:05) > > CPU0: T4240E, Version: 1.0, (0x82480010) > Core: E6500, Version: 1.0, (0x80400010) > Clock Configuration: > CPU0:1666.667 MHz, CPU1:1666.667 MHz, CPU2:1666.667 MHz, > CPU3:1666.667 MHz, > CPU4:1666.667 MHz, CPU5:1666.667 MHz, CPU6:1666.667 MHz, > CPU7:1666.667 MHz, > CPU8:1666.667 MHz, CPU9:1666.667 MHz, CPU10:1666.667 MHz, > CPU11:1666.667 MHz, > CCB:600 MHz, > DDR:400 MHz (800 MT/s data rate) (Asynchronous), IFC:150 MHz > FMAN1: 466.667 MHz > FMAN2: 466.667 MHz > QMAN: 300 MHz > PME: 300 MHz > L1: D-cache 32 kB enabled > I-cache 32 kB enabled > Reset Configuration Word (RCW): > 00000000: 120c0019 0c10190e 00000000 00000000 > 00000010: 04023033 00558c00 1c020000 19000000 > 00000020: 00000000 ee0000ee 00000000 000307fc > 00000030: 00000000 00000000 00000000 00000010 > Board: T4240QDS, Sys ID: 0x1e, Sys Ver: 0x24, vBank: 4 > FPGA: v3 (T4240QDS_2012_1113_1114), build 438 on Tue Nov 13 17:14:23 2012 > SERDES Reference Clocks: SERDES1=125MHz SERDES2=125MHz SERDES3=100MHz > SERDES4=100MHz > I2C: ready > SPI: ready > DRAM: Initializing....using SPD > Detected UDIMM 9JSF25672AZ-2G1K1 > Detected UDIMM 9JSF25672AZ-2G1K1 > Detected UDIMM 9JSF25672AZ-2G1K1 > 4 GiB left unmapped > DDR: 6 GiB (DDR3, 64-bit, CL=6, ECC on) > DDR Controller Interleaving Mode: 3-way 4KB > Flash: 128 MiB > L2: 2048 KB enabled > enable l2 for cluster 1 fec60000 > enable l2 for cluster 2 feca0000 > Corenet Platform Cache: 1536 KB enabled > Using SERDES1 Protocol: 1 (0x1) > Using SERDES2 Protocol: 1 (0x1) > Using SERDES3 Protocol: 6 (0x6) > Using SERDES4 Protocol: 6 (0x6) > SRIO1: enabled > SRIO2: enabled > NAND: 512 MiB > MMC: FSL_SDHC: 0 > EEPROM: NXID v1 > PCIe1: Root Complex, no link, regs @ 0xfe240000 > PCIe1: Bus 00 - 00 > PCIe2: disabled > PCIe3: Root Complex, no link, regs @ 0xfe260000 > PCIe3: Bus 01 - 01 > PCIe4: disabled > In: serial > Out: serial > Err: serial > Net: Fman1: Uploading microcode version 106.4.9 > Fman2: Uploading microcode version 106.4.9 > FM1@DTSEC5 [PRIME], FM1@TGEC1, FM2@DTSEC5 > Hit any key to stop autoboot: 0 > => > => setenv ethact FM1@TGEC1 > => setenv ethprime FM1@TGEC1 > => print > baudrate=115200 > bdev=sda3 > bootargs=root=/dev/mmcblk0p1 rw rootdelay=5 console=ttyS0,115200 > usdpaa_mem=256M bportals=s0-1 qportals=s0-1 > bootcmd=setenv bootargs root=/dev/mmcblk0p1 rw rootdelay=2 > console=$consoledev,$baudrate; > > mmcinfo;ext2load mmc 0:1 $loadaddr $bootfile;ext2load mmc 0:1 $fdtaddr > $fdtfile; bootm $loadaddr - $fdtaddr > bootdelay=3 > bootfile=uImage > consoledev=ttyS0 > eth10addr=00:04:9F:02:7A:39 > eth11addr=00:04:9F:02:7A:3A > eth12addr=00:04:9F:02:7A:3B > eth13addr=00:04:9F:02:7A:3C > eth14addr=00:04:9F:02:7A:3D > eth15addr=00:04:9F:02:7A:3E > eth1addr=00:04:9F:02:7A:30 > eth2addr=00:04:9F:02:7A:31 > eth3addr=00:04:9F:02:7A:32 > eth4addr=00:04:9F:02:7A:33 > eth5addr=00:04:9F:02:7A:34 > eth6addr=00:04:9F:02:7A:35 > eth7addr=00:04:9F:02:7A:36 > eth8addr=00:04:9F:02:7A:37 > eth9addr=00:04:9F:02:7A:38 > ethact=FM1@TGEC1 > ethaddr=00:04:9F:02:7A:2F > ethprime=FM1@TGEC1 > fdtaddr=0x17200000 > fdtfile=uImage-t4240qds.dtb > fileaddr=1000000 > filesize=46573C > fman_ucode=0xeff40000 > gatewayip=192.168.1.1 > > hwconfig=fsl_ddr:ctlr_intlv=3way_4KB,bank_intlv=auto;fsl_fm1_xaui_phy:xfi;fsl_fm2_xaui_phy:xfi > ipaddr=10.116.65.141 > loadaddr=0x10000000 > netdev=eth0 > netmask=255.255.255.0 > nfsboot=setenv bootargs root=/dev/nfs rw nfsroot=$serverip:$rootpath > ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off > console=$consoledev,$baudrate $othbootargs;tftp $loadaddr $bootfile;tftp > $fdtaddr $fdtfile;bootm $loadaddr - $fdtaddr > ramboot=setenv bootargs root=/dev/ram rw console=$consoledev,$baudrate > $othbootargs;tftp $ramdiskaddr $ramdiskfile;tftp $loadaddr $bootfile;tftp > $fdtaddr $fdtfile;bootm $loadaddr $ramdiskaddr $fdtaddr > ramdiskaddr=2000000 > ramdiskfile=t4240qds/ramdisk.uboot > rcw=t4240rcw > rcw_spi=mw.w ffdf0060 2201;qixis_reset altbank > rcwemmc=mw.w ffdf0060 2000 > rootpath=/opt/nfsroot > sataboot=setenv bootargs root=/dev/sda1 rootdelay=5 rw > console=$consoledev,$baudrate $othbootargs;bootm e8020000 - e8800000 > sdboot=setenv bootargs root=/dev/mmcblk0p1 rw rootdelay=5 > console=ttyS0,115200; ext2load mmc 0:1 $loadaddr $bootfile; ext2load mmc > 0:1 $fdtaddr $fdtfilel bootm $loadaddr - $fdtaddr > serverip=10.116.65.150 > stderr=serial > stdin=serial > stdout=serial > tftpflash=tftpboot $loadaddr $uboot && protect off $ubootaddr +$filesize > && erase $ubootaddr +$filesize && cp.b $loadaddr $ubootaddr $filesize && > protect on $ubootaddr +$filesize && cmp.b $loadaddr $ubootaddr $filesize > tftprcw=tftpboot $loadaddr $rcw && mmcinfo && mmc write 1000000 8 1 > uboot="u-boot.bin" > ubootaddr=0xeff80000 > > > regards, > > Hari Prasad S R > > 7418234575 > > > > On Tue, Jun 24, 2014 at 8:37 AM, [email protected] < > [email protected]> wrote: > > Do you use the usdpaa dtb(t4240qds-usdpaa.dtb)? Please provide more > details, e.g. u-boot setting, bootargs, etc. > > > > > > Best Regards, > > > > Zhenhua > > > > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *hari prasad > *Sent:* Monday, June 23, 2014 5:59 PM > *To:* [email protected] > *Subject:* [meta-freescale] t4240 offloading applications > > > > HI, > > I am trying to run usdpaa offloading applications in t4240qds but drivers > dpa_stats and dpa_classifier are not present in /dev/ . How can I get these > applications to work > > regards, > > Hari Prasad S R > > 7418234575 > > >
-- _______________________________________________ meta-freescale mailing list [email protected] https://lists.yoctoproject.org/listinfo/meta-freescale
