I might have used it wrong, my last test gives good results.
T.Holst
At 07:16 PM 5/25/00 +0200, I wrote:
>Ther is a problem about the circles. Revgen don't handle circles over 180
deg.
>I think the problem can be fixed by add some code in the cut.awk file:
>
>
>....
>...
>
>#----------- Arc XY Section --------------------------------
>
> if ( plnmode == "G17" ) {
> if ( gmode == "G02" || gmode == "G03" ) {
> if ( lastmode == "G01" ) {
> print " }"
> print " ]"
> }
> stpointx = thex
> stpointy = they
> stpointz = thez
> calcenter(stpointx,stpointy,stpointz,thei,thej,thek)
> calrad(stpointx,stpointy,stpointz,centerx,centery,centerz)
> calxyz(searchX,searchY,searchZ,endline)
> endpointx = thex
> endpointy = they
> endpointz = thez
> if ( arcdirxy != "reverse" ) {
> if ( gmode == "G02" ) {
> printf ("ARC[DR=0, XC=%.6f, YC=%.6f, XS=%.6f, YS=%.6f,
>XE=%.6f, YE=%.6f, LV=%.6f]\n", centerx, centery, stpointx, stpointy,
>endpointx, endpointy, thez)
> lastmode = "G02"
> }
> if ( gmode == "G03" ) {
> printf ("ARC[DR=1, XC=%.6f, YC=%.6f, XS=%.6f, YS=%.6f,
>XE=%.6f, YE=%.6f, LV=%.6f]\n", centerx, centery, stpointx, stpointy,
>endpointx, endpointy, thez)
> lastmode = "G03"
> }
> }
> if ( arcdirxy == "reverse" ) {
> if ( gmode == "G02" ) {
> printf ("ARC[DR=1, RA=%.6f, XS=%.6f, YS=%.6f, XE=%.6f,
>YE=%.6f, LV=%.6f]\n", radius, stpointx, stpointy, endpointx, endpointy, thez)
> lastmode = "G02"
> }
> if ( gmode == "G03" ) {
> printf ("ARC[DR=0, RA=%.6f, XS=%.6f, YS=%.6f, XE=%.6f,
>YE=%.6f, LV=%.6f]\n", radius, stpointx, stpointy, endpointx, endpointy, thez)
> lastmode = "G03"
> }
> }
> }
> }
># ARC[XC=##, YC=##, XS=##, YS=##, XE=##, YE=##,
># XI=##, YI=##, SS=##, SC=##, TS=$$, AS=##,
># SE=##, TE=$$, AE=##, SI=##, TI=$$, DR=##,
># RA=##, LV=##]
>...
>..
>#------------- Function to determine x,y,z ----------------------
>....
>...
>function calcenter(stpointx,stpointy,stpointz,thei,thej,thek){
>
> if ( implied == 0 ) {
> places = 1.0
> }
> if ( implied == 1 ) {
> places = 10.0
> }
> if ( implied == 2 ) {
> places = 100.0
> }
> if ( implied == 3 ) {
> places = 1000.0
> }
> if ( implied == 4 ) {
> places = 10000.0
> }
> if ( implied == 5 ) {
> places = 100000.0
> }
> if ( implied == 6 ) {
> places = 1000000.0
> }
>
> searchI = match($0,"I")
> searchJ = match($0,"J")
> searchK = match($0,"K")
> searchR = match($0,"R")
> thei = (substr($0,searchI+1,endline))/places
> thej = (substr($0,searchJ+1,endline))/places
> thek = (substr($0,searchK+1,endline))/places
> if ( arcmode == "start_center" ) {
> centerx = stpointx + thei
> centery = stpointy + thej
> centerz = stpointz + thek
> }
> if ( arcmode == "center_start" ) {
> centerx = stpointx - thei
> centery = stpointy - thej
> centerz = stpointz - thek
> }
> if ( arcmode == "absolute" ) {
> centerx = thei
> centery = thej
> centerz = thek
> }
>
>return centerx centery centerz thei thej thek
>
>}
>....
>...
>
>------------------------
>
>an extra function determin small ore big circle is neded I think
>
>T.Holst
>
>
>At 11:17 AM 5/25/00 -0400, you wrote:
>>Hey all
>>
>>There were several posts some time ago concerning reverse code generation;
>>creating a model from code.
>>
>>Did anyone ever have any success with this and if so, where can I get the
>>program?
>>
>>Thanks
>>Pete
>>
>>
>>_______________________________________________________
>>Peter Ruehle
>>Semiconductor Packaging Materials
>>[EMAIL PROTECTED]
>>http://www.sempck.com
>>(914) 273-5500
>>
>>======================================================================
>>To find out more about this mailing list including how to unsubscribe,
>>send the message "info mfg-smartcam" to [EMAIL PROTECTED]
>>======================================================================
>>
>---------------------
>PROTOTECH AS
>P.O. Box 6034
>N-5892 Bergen, Norway.
>======================================================================
>To find out more about this mailing list including how to unsubscribe,
>send the message "info mfg-smartcam" to [EMAIL PROTECTED]
>======================================================================
>
---------------------
PROTOTECH AS
P.O. Box 6034
N-5892 Bergen, Norway.
======================================================================
To find out more about this mailing list including how to unsubscribe,
send the message "info mfg-smartcam" to [EMAIL PROTECTED]
======================================================================
