TESTING 1.2.3..
> -----Original Message-----
> From: Michael Senack [SMTP:[EMAIL PROTECTED]]
> Sent: Friday, November 08, 2002 11:26 AM
> To: 'Stannard, Rick'; '[EMAIL PROTECTED]'; [EMAIL PROTECTED]
> Subject: RE: [mfg-smartcam] FW: Macro Question
>
> We're still here. I've been receiving a couple of posts from the group on
> a daily basis.
> However it seems that when I "reply to all", not all my e-mails are
> getting thru.
> Hmmm.
>
> Regards,
> Michael Senack
>
> -----Original Message-----
> From: Stannard, Rick [mailto:[EMAIL PROTECTED]]
> Sent: Friday, November 08, 2002 1:12 PM
> To: '[EMAIL PROTECTED]'; [EMAIL PROTECTED]
> Subject: RE: [mfg-smartcam] FW: Macro Question
>
>
>
> I am sorry for this, but I haven't gotten any e-mails for a long
> time, seems like a couple of weeks at least and I was wondering if my
> company isn't allowing these to come thru or possibly this group has gone
> by the way side?
>
> Is the group still alive?
> Regards, Rick
>
> -----Original Message-----
> From: [EMAIL PROTECTED] [ <mailto:[EMAIL PROTECTED]>]
> Sent: Monday, October 14, 2002 5:36 AM
> To: [EMAIL PROTECTED]
> Subject: [mfg-smartcam] FW: Macro Question
>
>
> Jeff,
>
> You need to use the PROPERTY command to turn on and off the tool
> offset and
> user commands to change the feed rate at the appropriate times
> within the
> profile .
>
> PROPERTY[OF=2]// no tool offset
>
> UEVENT[XS=#xctr, YS=#yctr, LV=#zstrt, TX="#FEED=100"]// feed rate
> set by
> macro
> // - or, try this -
> UEVENT[XS=#xctr, YS=#yctr, LV=#zstrt, TX="#FEED=jos(outfeed3)"]//
> plunge
> feed from planner
>
> LINE[XS=#xctr, YS=#yctr, ZS=#zstrt, XE=#xctr, YE=#yctr, ZE=#zend]
>
> PROPERTY[OF=0]// tool offset left
> UEVENT[XS=#xctr, YS=#yctr, LV=#zend, TX="#FEED=6"]// feed rate set
> by macro
> // - or, try this -
> UEVENT[XS=#xctr, YS=#yctr, LV=#zend, TX="#FEED=jos(outfeed1)"]//
> primary
> feed from planner
>
> LINE[XS=#xctr, YS=#yctr, ZS=#zend, XE=#xctr+.1, YE=#dia-.00-#tldia,
> AE=270]
> ARC[DR=1, XC=#xctr+.1, YC=#yctr, RA=#dia/2-.1-#tldia/2, AS=270,
> AE=0, SE=2, SS=2, SI=2, SC=2, LV=#zend]
>
> ARC[DR=1, XC=#xctr, YC=#yctr, ZS=#zstrt, RA=#dia/2-.00-#tldia/2,
> AS=0,
> AE=0, SE=2, SS=2, SI=2, SC=2, RT=360, LV=#zend]
> ARC[DR=1, XC=#xctr+.1, YC=#yctr, RA=#dia/2-.1-#tldia/2, AS=0,
> AE=90, SE=2, SS=2, SI=2, SC=2, LV=#zend]
> LINE[XS=#xctr+.1, YS=#dia, ZS=#zend, XE=#xctr, YE=#yctr, AS=90]
>
> PROPERTY[OF=2]// no tool offset
>
> POINT[XE=#xctr, YE=#yctr, LV=#zstrt, CO=0, SE=2]
>
> If the geometry is correct, the corresponding output of FEED, D, G41
>
> and G40 values may be a code generator issue.
>
> =============================================
> Fred Lauzus, CAM Programming Coordinator
> High Steel Structures, Incorporated
> <mailto:[EMAIL PROTECTED]> < <mailto:[EMAIL PROTECTED]>>
> <http://www.highsteel.com> < <http://www.highsteel.com/>>
> =============================================
>
> -----Original Message-----
> From: Jeff [ <mailto:[EMAIL PROTECTED]>]
> Sent: Saturday, October 12, 2002 2:17 PM
> To: [EMAIL PROTECTED]
> Subject: Macro Question
>
>
> Fred,
> Could you please help me solve this macro problem.
> I'm not real familiar with macros and I've been spending way to much
> time on
> trying
> to solve this one.
>
> I'm trying to build a macro that outputs the entire profile from
> .300 above
> the part to a
> specified level to interpolate then rapid out back to .300 above for
>
> differant dia. T-Slot cutters.
>
> The elements should look like this:
>
> 1. #FEED=100
> 2. LINE (-0.7 - ? Depth)
> 3. #FEED=6
> 4. G41 D#TOOL
> 4. LINE (? Depth to entry arc)
> 5. ARC (Ramp in)
> 6. ARC (? Dia. of Full arc to interpolate)
> 7. ARC (Ramp out)
> 8. LINE (Cuts back to Center)
> 9. POINT (Rapids Out)
> 10. G40
>
> The macro will ask questions for XCENTER, YCENTER, ZSTART, ZEND,
> DIAMETER
> AND TOOL DIA.
> The attached macro does everything fine on the profile except the
> lines
> leading to the lead-in arc
> and from the lead-out arc. This is what I need the help with, I'm
> sure it's
> very simple I just can't
> figure it out.
> I'd also like the FEED, G41, D/offset and G40 to output if possible.
>
>
> All help would be greatly appreciated.
> Thank You
>
> Jeff Pieper
> EATON Hydraulics
>
======================================================================
To find out more about this mailing list including how to unsubscribe,
send the message "info mfg-smartcam" to [EMAIL PROTECTED]
======================================================================
