RE: [mfg-smartcam] Code Generator

[Michael R. Deren]

Title: RE: [mfg-smartcam] Code Generator

Rick,

This temp file was started by someone else and had those variables in there. Not being real familiar with it, I didn't want to mess with it. Maybe I'll just double backslash all of those lines.

Mike

 

 

 -----Original Message-----
From: Stannard, Rick [mailto:[EMAIL PROTECTED]
Sent: Friday, August 15, 2003 9:25 AM
To: 'Michael R. Deren'; SmartCam Users Forum (E-mail)
Subject: RE: [mfg-smartcam] Code Generator

Michael,
  I couldn't figure out where you get your values for #V9, #V8, #V7, #V6 in #FXD1 the first time thru.  At the end of this section you do a #EVAL on them.  Just curious if this may be your problem.

  Rick

-----Original Message-----
From: Michael R. Deren [mailto:[EMAIL PROTECTED]]
Sent: Friday, August 15, 2003 5:09 AM
To: SmartCam Users Forum (E-mail)
Subject: [mfg-smartcam] Code Generator

I hope someone can help.
I have been working on a code generator for a Heidenhein TNC 426 control.
Everything else is ok, except for the fixed cycles. I am having trouble with
them, to say the least. I have attached my .smp and .tmp files. Below is the
section I am having trouble with.

@ZCLRMV
#EVAL(#V1=#ZPOS)
//#IF(#XSET=1,#AND #TLOP<>2)<#EXIT>
//#EVAL(#NHOL=#NHOL+1)
//#IF(#NHOL=2,#AND #TLOP<>2)<#EXIT>
//< L Z#V1 R0 F MAX>

@ZCHKMV
//#IF(#XSET>=1,#AND #TLOP<>2)<#EXIT>
//#IF(#C1=1)<#EVAL(#NHOL=#NHOL+10)#EVAL(#C1=0)>
//#IF(#NHOL<=2,#AND #TLOP<>2)<#EXIT>
//#EVAL(#NHOL=#NHOL+1)
 L Z#ZPOS R0 F MAX

@ZDPTHMV
#EVAL(#V14=INT(#FEED*10))
< L Z#ZPOS R0 F#V14>

@FXD1
#EVAL(#V3=0)
//#IF(#V9<>#ZDPTH)<#EVAL(#ZDPTH=#ZDPTH+0.125)>
#IF(#V9<>#ZDPTH)<#EVAL(#V3=1)>
#IF(#V8<>#ZCHK)<#EVAL(#V3=1)>
#IF(#V7<>100)<#EVAL(#V3=1)>
#IF(#V6<>#FXD)<#EVAL(#V3=1)>
#EVAL(#V12=ABS(#V18))
//#EVAL(#V13=#PTOP-#ZCHK+0.125)
#EVAL(#V14=INT(#FEED*10))
#EVAL(#V16=#PTOP-#CHKD)
#EVAL(#V17=#V12+ABS(#V16)+0.125)
#EVAL(#V18=(#ZDPTH-#V16)
< L Z+20 R0 F MAX>
aa#IF(#V3=1)< CYCL DEF 200 DRILLING ~>#ELSE< L X#XPOS Y#YPOS R0 F MAX M99
M13>
#OFFBLK#IF(#V3=1)<    Q200 = 0.125 ;SET UP CLEARANCE ~>
#IF(#V3=1)<    Q201 =#V18 ;DEPTH~>
#IF(#V3=1)<    Q206 =#V14 ;FEEDRATE FOR PLUNGING ~>
#IF(#V3=1)<    Q202 =#V12 ;PLUNGING DEPTH ~>
#IF(#V3=1)<    Q210 =0 ;DWELL TIME AT TOP ~>
#IF(#V3=1)<    Q203 =#V16 ;SURFACE COORDINATE ~>
#IF(#V3=1)<    Q204 =#V17 ;2ND SET-UP CLEARANCE ~>
#IF(#V3=1)<    Q211 =0 ;DWELL TIME AT BOTTOM>
//#ONBLK#IF(#V3=1) <L M13>
#EVAL(#V14=#FEED)
#EVAL(#V9=#ZDPTH)
#EVAL(#V8=#ZCHK)
#EVAL(#V7=100)
#EVAL(#V6=#FXD)
#ONBLK#IF(#V3=1)< L X#XPOS Y#YPOS R0 F MAX M99 M13>

I am not sure about the #ZCHK, #ZCLR, #ZDPTH.
The values in the canned cycle are as follows:

Q200 = This should be our z clearance which I need to be 0.125
Q201 = The incremental depth of the drilled hole
Q206 = This ones ok
Q202 = This is the incremental depth, which should be the same as Q201
Q210 = This is ok
Q203 = Is to be the Profile Top
Q204 = This is to be the incremental value to get back up to my z clearance
above the top of the part
Q211 = This is ok

I think I may have my settings incorrect in the .smp file. This is why I
have all kinds of variables and formulas in the section.

Any help would be greatly appreciated.
Mike Deren

 <<BMT125.tMP>>  <<BMT125_H.SMF>>