Your going to need heat. _http://cgi.ebay.com/CRAFTSMAN-OXYGEN-MAPP-GA S-TORCH-OUTFIT-WELD%2FCUT%2FBRAZE_W0QQitemZ350095105911QQcmdZViewItem_ (http://cgi.ebay.com/CRAFTSMAN-OXYGEN-MAPP-GAS-TORCH-OUTFIT-WELD/CUT/BRAZE_W0QQitemZ350095105911QQcmdZViewItem) I bought this kit when I had an axle nut that refused to come out. I needed something cheap and much hotter than a propane torch and this kit worked perfectly. About 5 minutes of heating started to get the nut red and it then came off like it was hand tight! The only issue with this kit is that it will eat oxygen tanks when your going for a hot flame so keep a couple in stock. I don't think Sears still sells the kit since I couldn't find it on there site but they do have it at my local store along with mapp and oxygen refill tanks. But I did find this one that is quite a bit more than what I paid but should do the job as well, _http://www.toolfetch.com/Category--Welding--Soldering_Brazing--189-OX2550KC.shtml_ (http://www.toolfetch.com/Category--Welding--Soldering_Brazing--189-OX2550KC.shtml) Raj In a message dated 9/5/2008 4:05:27 P.M. Eastern Daylight Time, [EMAIL PROTECTED] writes:
You might try tightening it a touch to break the gunk loose. -----Original Message----- From: [EMAIL PROTECTED] on behalf of [EMAIL PROTECTED] Sent: Fri 9/5/2008 3:55 PM To: Bill Bowser Cc: [EMAIL PROTECTED]; Miata Power List Subject: Re: stuck bolt, part duex Yes, 1/2" breaker bars flex too much. I got a really beefy 3/4 breaker bar at Harbor Freight for around $20. Nothing can defeat that thing ! Steve Bill Bowser <[EMAIL PROTECTED] t> To Sent by: miatapower-bounce cc [EMAIL PROTECTED] Miata Power List <[email protected]> Subject 09/05/2008 01:11 Re: stuck bolt, part duex PM I'd suggest using a 3/4" drive breaker bar and socket. Unfortunately they can be quite expensive and somewhat hard to find. Several years ago I picked up a 3/4" drive ratchet set of Chinese origin for only $30. There have been a few occasions when I was very glad I had it. When I changed out my differential was one, and my car has never been exposed to road salt or winter weather. FYI, Harbor Freight currently sells 3/4" ratchet sets for $49.99 & $59.99. Bill Bowser pm wrote: i just split my impact 17mm with an extension on my 1/2" ratchet trying to break the PPF bolt free...........S! S! S! more suggestions? -- Medio tutissmus ibis You will go most safely by the middle course _______________________________________________ Miatapower mailing list [email protected] _http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower_ (http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower) No virus found in this incoming message. Checked by AVG. Version: 7.5.526 / Virus Database: 270.6.16/1653 - Release Date: 9/5/2008 6:57 AM ______________________________________________________________________ This email has been scanned by the MessageLabs Email Security System. For more information please visit _http://www.messagelabs.com/email_ (http://www.messagelabs.com/email) ______________________________________________________________________ _______________________________________________ Miatapower mailing list [email protected] _http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower_ (http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower) _______________________________________________ Miatapower mailing list [email protected] _http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower_ (http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower) _______________________________________________ Miatapower mailing list [email protected] http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower **************Psssst...Have you heard the news? There's a new fashion blog, plus the latest fall trends and hair styles at StyleList.com. (http://www.stylelist.com/trends?ncid=aolsty00050000000014)
_______________________________________________ Miatapower mailing list [email protected] http://list.miatapower.net/cgi-bin/mailman/listinfo/miatapower
