Ah ha, Thanks Bill What's the difference between an RB600, RB800 and an Intel Atom with 4x Radio cards?
Surely if it works with the RB800's then it should work with the Intel Atom? Would a 40mhz channel remedy the issue? Thanks -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Bill Prince Sent: 12 November 2010 12:55 AM To: [email protected] Subject: Re: [Mikrotik] Need to NAT 10 to 15 offices - gigabit Just to be clear. The throughput of the plain vanilla PCI bus is 133 Mega BYTES/second (AKA 133.3 MB/s (note the big "B")). That is total throughput. Translate that to bits (little b) it is 1,067 Mbps. So getting 4 * 35 Mbps (140 Mbps) throughput should not be a major problem. Getting 4 radios to work in close proximity would probably be a major problem. bp On 11/11/2010 2:10 PM, james wrote: > Hi Josh > > Thanks for the info. > > Is that 133mbps full duplex throughput? Or only 65mbps full duplex? > > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Josh Luthman > Sent: 11 November 2010 11:31 PM > To: Mikrotik discussions > Subject: Re: [Mikrotik] Need to NAT 10 to 15 offices - gigabit > > Pci shouldn't be a problem, but asking 35 megs per radio might be. > On Nov 11, 2010 3:26 PM, "james"<[email protected]> wrote: >> Hi Josh >> >> Would a PCI to 4 port mPCI card adapter with 4x Radio's be able to get at >> least 133Mbps throughput? >> >> I am looking at purchasing an Intel Atom and adding 4x Radio cards but I'm >> worried about the performance of the PCI card >> >> Thanks >> >> >> -----Original Message----- >> From: [email protected] >> [mailto:[email protected]] On Behalf Of Josh Luthman >> Sent: 03 November 2010 05:16 PM >> To: Mikrotik discussions >> Subject: Re: [Mikrotik] Need to NAT 10 to 15 offices - gigabit >> >> PCI >> >> Capacity 133 MB<http://en.wikipedia.org/wiki/Megabyte>/s (32-bit at 33 > MHz) >> 266 MB/s (32-bit at 66 MHz or 64-bit at 33 MHz) >> 533 MB/s (64-bit at 66 MHz) >> >> PCI X >> >> Capacity >> >> Per lane: >> >> - *v1.x*: 250 MB/s >> - *v2.x*: 500 MB/s >> - *v3.0*: 1 GB/s >> >> 16 lane slot: >> >> - *v1.x*: 4 GB/s >> - *v2.x*: 8 GB/s >> - *v3.0*: 16 GB/s >> >> >> >> Josh Luthman >> Office: 937-552-2340 >> Direct: 937-552-2343 >> 1100 Wayne St >> Suite 1337 >> Troy, OH 45373 >> >> >> On Wed, Nov 3, 2010 at 11:08 AM, Casey Mills<[email protected]> wrote: >> >>> Anyone using these? >>> http://www.roc-noc.com/product.php?productid=55&cat=0&page=1 >>> >>> It is getting much harder to find a board with this many PCI slots. >>> Maybe Mikrotik needs to make a PCI Express card. >>> http://www.newegg.com/Product/Product.aspx?Item=N82E16813121412 >>> >>> It even has a PATA / IDE port for you DOM. Why use a hard drive that >>> has moving parts. It will eventually fail. >>> >>> Anyone know the bus limitations on PCI? Can a PCI port even transfer >>> 4 gigabits per second? >>> >>> Casey >>> >>> >>> >>> On Wed, Nov 3, 2010 at 9:10 AM, Paul McCall<[email protected]> wrote: >>>> Thanks Guys for the suggestions >>>> >>>> -----Original Message----- >>>> From: [email protected] >>>> [mailto:[email protected]] On Behalf Of Andrew Cox >>>> Sent: Wednesday, November 03, 2010 1:39 AM >>>> To: Mikrotik discussions >>>> Subject: Re: [Mikrotik] Need to NAT 10 to 15 offices - gigabit >>>> >>>> I'd recommend this way also (building / buying x86 boxes). >>>> There's a good thread on the MT forums from a guy who was quite happily >>>> running 10Gbps interfaces on Dell PowerEdge 860's back in v3.X >>>> >>>> http://forum.mikrotik.com/viewtopic.php?f=2&t=19245 >>>> <http://forum.mikrotik.com/viewtopic.php?f=2&t=19245> >>>> >>>> - Andrew >>>> >>>> On 03/11/2010 01:29, Travis Johnson wrote: >>>>> Hi, >>>>> >>>>> I would build my own x86 based Mikrotik boxes with as many GigE ports >>>>> as you need (or use multiple boxes). You can build a much more >>>>> powerful system for the same or less money than an RB1100. >>>>> >>>>> Even the ATOM processor based Supermicro boards have a LOT more >>>>> horsepower, and some come with two GigE ports right on the board. >>>>> >>>>> Travis >>>>> Microserv >>>>> >>>>> >>>>> On 11/2/2010 8:47 PM, Paul McCall wrote: >>>>>> We have an office complex where we have wired up 15 offices. >>>>>> Typically, we put in as many RB493s tied together as it takes, with >>>>>> each available port doing NAT/DHCP on a separate network. >>>>>> >>>>>> In this case, we have fiber to the building, and we have gigabit >>>>>> access to Radiological Images, where a series of images can be quite >>>> large. >>>>>> So, having gigabit to each customer unit is required to "do it >>>> right". >>>>>> Obviously, I want something that can handle some pretty good "bursty" >>>>>> traffic. I would guess that only one or two units would actually be >>>>>> doing the big transfers at one time, but I want them to be >>>> super-fast... >>>>>> kinda get in, get the data, get done.. >>>>>> >>>>>> My considerations thus far have been a RB1100. >>>>>> >>>>>> Is there a better/faster/cheaper way to do this? >>>>>> >>>>>> Paul, PDMNet >>>>>> _______________________________________________ >>>>>> Mikrotik mailing list >>>>>> [email protected] >>>>>> http://www.butchevans.com/mailman/listinfo/mikrotik >>>>>> >>>>>> Visit http://blog.butchevans.com/ for tutorials related to Mikrotik >>>>>> RouterOS >>>>>> >>>>> _______________________________________________ >>>>> Mikrotik mailing list >>>>> [email protected] >>>>> http://www.butchevans.com/mailman/listinfo/mikrotik >>>>> >>>>> Visit http://blog.butchevans.com/ for tutorials related to Mikrotik >>>>> RouterOS >>>> _______________________________________________ >>>> Mikrotik mailing list >>>> [email protected] >>>> http://www.butchevans.com/mailman/listinfo/mikrotik >>>> >>>> Visit http://blog.butchevans.com/ for tutorials related to Mikrotik >>>> RouterOS >>>> _______________________________________________ >>>> Mikrotik mailing list >>>> [email protected] >>>> http://www.butchevans.com/mailman/listinfo/mikrotik >>>> >>>> Visit http://blog.butchevans.com/ for tutorials related to Mikrotik >>> RouterOS >>> _______________________________________________ >>> Mikrotik mailing list >>> [email protected] >>> http://www.butchevans.com/mailman/listinfo/mikrotik >>> >>> Visit http://blog.butchevans.com/ for tutorials related to Mikrotik >>> RouterOS >>> >> -------------- next part -------------- >> An HTML attachment was scrubbed... >> URL: >> < > http://www.butchevans.com/pipermail/mikrotik/attachments/20101103/5437d154/ >> attachment.html> >> _______________________________________________ >> Mikrotik mailing list >> [email protected] >> http://www.butchevans.com/mailman/listinfo/mikrotik >> >> Visit http://blog.butchevans.com/ for tutorials related to Mikrotik > RouterOS >> _______________________________________________ >> Mikrotik mailing list >> [email protected] >> http://www.butchevans.com/mailman/listinfo/mikrotik >> >> Visit http://blog.butchevans.com/ for tutorials related to Mikrotik > RouterOS > -------------- next part -------------- > An HTML attachment was scrubbed... > URL: > <http://www.butchevans.com/pipermail/mikrotik/attachments/20101111/48557aa2/ > attachment.html> > _______________________________________________ > Mikrotik mailing list > [email protected] > http://www.butchevans.com/mailman/listinfo/mikrotik > > Visit http://blog.butchevans.com/ for tutorials related to Mikrotik RouterOS > > _______________________________________________ > Mikrotik mailing list > [email protected] > http://www.butchevans.com/mailman/listinfo/mikrotik > > Visit http://blog.butchevans.com/ for tutorials related to Mikrotik RouterOS > _______________________________________________ Mikrotik mailing list [email protected] http://www.butchevans.com/mailman/listinfo/mikrotik Visit http://blog.butchevans.com/ for tutorials related to Mikrotik RouterOS _______________________________________________ Mikrotik mailing list [email protected] http://www.butchevans.com/mailman/listinfo/mikrotik Visit http://blog.butchevans.com/ for tutorials related to Mikrotik RouterOS
