All,
Please forgive the lengthy post. I am pulling what little hair I have left out
to try and see why this will not work.
I have taken the following file (below) and pasted it on the router line by
line and have absolutely no errors. But when I upload it to the router and do a
system --> reset configuration --> run after reset and use this file (one I
reset with "no default configuration") the neighbor viewer shows up with an ip
of 0.0.0.0 and I get into it via mac address and it has absolutely no settings.
Anyone have any idea what I could be missing?
Thanks in advance!!!
/interface bridge
add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes
disabled=no forward-delay=15s l2mtu=65535 \
max-message-age=20s mtu=1500 name=loopback1 priority=0x8000
protocol-mode=none transmit-hold-count=6
add admin-mac=00:00:00:00:00:00 ageing-time=5m arp=enabled auto-mac=yes
disabled=no forward-delay=15s l2mtu=1598 max-message-age=\
20s mtu=1500 name=bridge1 priority=0x8000 protocol-mode=none
transmit-hold-count=6
/interface
set ether1 disabled=no l2mtu=1598 mtu=1500 name=ether1
set ether2 disabled=no l2mtu=1598 mtu=1500 name=ether2
set ether3 disabled=no l2mtu=1598 mtu=1500 name=ether3
set ether4 disabled=no l2mtu=1598 mtu=1500 name=ether4
set ether5 disabled=no l2mtu=1598 mtu=1500 name=ether5
/interface ethernet switch
set 0 mirror-source=none mirror-target=none name=switch1
/ip hotspot profile
set [ find default=yes ] dns-name="" hotspot-address=0.0.0.0
html-directory=hotspot http-cookie-lifetime=3d http-proxy=0.0.0.0:0 \
login-by=cookie,http-chap name=default rate-limit="" smtp-server=0.0.0.0
split-user-domain=no use-radius=no
/ip hotspot user profile
set [ find default=yes ] idle-timeout=none keepalive-timeout=2m name=default
shared-users=1 status-autorefresh=1m \
transparent-proxy=no
/ip ipsec proposal
set [ find default=yes ] auth-algorithms=sha1 disabled=no enc-algorithms=3des
lifetime=30m name=default pfs-group=modp1024
add auth-algorithms=sha1 disabled=no enc-algorithms=3des lifetime=30m
name=juniper pfs-group=none
/ppp profile
set 0 change-tcp-mss=yes name=default only-one=default
remote-ipv6-prefix-pool=none use-compression=default use-encryption=\
default use-ipv6=yes use-mpls=default use-vj-compression=default
set 1 change-tcp-mss=yes name=default-encryption only-one=default
remote-ipv6-prefix-pool=none use-compression=default \
use-encryption=yes use-ipv6=yes use-mpls=default use-vj-compression=default
/queue type
set 0 kind=pfifo name=default pfifo-limit=50
set 1 kind=pfifo name=ethernet-default pfifo-limit=50
set 2 kind=sfq name=wireless-default sfq-allot=1514 sfq-perturb=5
set 3 kind=red name=synchronous-default red-avg-packet=1000 red-burst=20
red-limit=60 red-max-threshold=50 red-min-threshold=10
set 4 kind=sfq name=hotspot-default sfq-allot=1514 sfq-perturb=5
set 5 kind=none name=only-hardware-queue
set 6 kind=mq-pfifo mq-pfifo-limit=50 name=multi-queue-ethernet-default
set 7 kind=pfifo name=default-small pfifo-limit=10
/routing bgp instance
set default as=65530 client-to-client-reflection=yes disabled=no
ignore-as-path-len=no name=default out-filter="" \
redistribute-connected=no redistribute-ospf=no redistribute-other-bgp=no
redistribute-rip=no redistribute-static=no \
router-id=0.0.0.0 routing-table=""
/routing ospf instance
set [ find default=yes ] disabled=no distribute-default=never in-filter=ospf-in
metric-bgp=auto metric-connected=20 \
metric-default=1 metric-other-ospf=auto metric-rip=20 metric-static=20
name=default out-filter=ospf-out redistribute-bgp=no \
redistribute-connected=no redistribute-other-ospf=no redistribute-rip=no
redistribute-static=no router-id=0.0.0.0
/routing ospf area
set [ find default=yes ] area-id=0.0.0.0 disabled=no instance=default
name=backbone type=default
/routing ospf-v3 instance
set [ find default=yes ] disabled=no distribute-default=never metric-bgp=auto
metric-connected=20 metric-default=1 \
metric-other-ospf=auto metric-rip=20 metric-static=20 name=default
redistribute-bgp=no redistribute-connected=no \
redistribute-other-ospf=no redistribute-rip=no redistribute-static=no
router-id=0.0.0.0
/routing ospf-v3 area
set [ find default=yes ] area-id=0.0.0.0 disabled=no instance=default
name=backbone type=default
/snmp community
set [ find default=yes ] addresses=0.0.0.0/0 authentication-password=""
authentication-protocol=MD5 encryption-password="" \
encryption-protocol=DES name=public read-access=yes security=none
write-access=no
add addresses=0.0.0.0/0 authentication-password="" authentication-protocol=MD5
encryption-password="" encryption-protocol=DES \
name=MNS2AirLiquide read-access=yes security=none write-access=yes
/system logging action
set 0 memory-lines=100 memory-stop-on-full=no name=memory target=memory
set 1 disk-file-count=2 disk-file-name=log disk-lines-per-file=100
disk-stop-on-full=no name=disk target=disk
set 2 name=echo remember=yes target=echo
set 3 bsd-syslog=no name=remote remote=:: remote-port=514 src-address=0.0.0.0
syslog-facility=daemon syslog-severity=auto target=\
remote
/user group
set read name=read
policy=local,telnet,ssh,reboot,read,test,winbox,password,web,sniff,sensitive,api,!ftp,!write,!policy
skin=\
default
set write name=write
policy=local,telnet,ssh,reboot,read,write,test,winbox,password,web,sniff,sensitive,api,!ftp,!policy
skin=\
default
set full name=full
policy=local,telnet,ssh,ftp,reboot,read,write,policy,test,winbox,password,web,sniff,sensitive,api
skin=default
/interface bridge port
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none
interface=ether2 path-cost=10 point-to-point=auto \
priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none
interface=ether1 path-cost=10 point-to-point=auto \
priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none
interface=ether3 path-cost=10 point-to-point=auto \
priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none
interface=ether4 path-cost=10 point-to-point=auto \
priority=0x80
add bridge=bridge1 disabled=no edge=auto external-fdb=auto horizon=none
interface=ether5 path-cost=10 point-to-point=auto \
priority=0x80
/interface bridge settings
set use-ip-firewall=no use-ip-firewall-for-pppoe=no use-ip-firewall-for-vlan=no
/interface ethernet switch port
set 0 vlan-header=leave-as-is vlan-mode=disabled
set 1 vlan-header=leave-as-is vlan-mode=disabled
set 2 vlan-header=leave-as-is vlan-mode=disabled
set 3 vlan-header=leave-as-is vlan-mode=disabled
set 4 vlan-header=leave-as-is vlan-mode=disabled
set 5 vlan-header=leave-as-is vlan-mode=disabled
/interface l2tp-server server
set authentication=pap,chap,mschap1,mschap2 default-profile=default-encryption
enabled=no keepalive-timeout=30 max-mru=1460 \
max-mtu=1460 mrru=disabled
/interface ovpn-server server
set auth=sha1,md5 certificate=none cipher=blowfish128,aes128
default-profile=default enabled=no keepalive-timeout=60 mac-address=\
FE:7D:12:78:37:F4 max-mtu=1500 mode=ip netmask=24 port=1194
require-client-certificate=no
/interface pptp-server server
set authentication=mschap1,mschap2 default-profile=default-encryption
enabled=no keepalive-timeout=30 max-mru=1460 max-mtu=1460 \
mrru=disabled
/interface sstp-server server
set authentication=pap,chap,mschap1,mschap2 certificate=none
default-profile=default enabled=no keepalive-timeout=60 max-mru=1500 \
max-mtu=1500 mrru=disabled port=443 verify-client-certificate=no
/ip accounting
set account-local-traffic=no enabled=no threshold=256
/ip accounting web-access
set accessible-via-web=no address=0.0.0.0/0
/ip address
add address=5.x.x.x/32 comment="IPSec Interface" disabled=no
interface=loopback1 network=5.x.x.x
add address=68.x.x.x/26 comment="WAN Access" disabled=no interface=bridge1
network=68.x.x.x
/ip dhcp-server config
set store-leases-disk=5m
/ip dns
set allow-remote-requests=yes cache-max-ttl=1w cache-size=2048KiB
max-udp-packet-size=4096 servers=\
208.67.220.220,208.67.222.222,8.8.8.8,8.8.4.4
/ip dns static
add address=68.x.x.x disabled=no name=router ttl=1d
/ip firewall connection tracking
set enabled=yes generic-timeout=10m icmp-timeout=10s tcp-close-timeout=10s
tcp-close-wait-timeout=10s tcp-established-timeout=1d \
tcp-fin-wait-timeout=10s tcp-last-ack-timeout=10s
tcp-syn-received-timeout=5s tcp-syn-sent-timeout=5s tcp-syncookie=no \
tcp-time-wait-timeout=10s udp-stream-timeout=3m udp-timeout=10s
/ip firewall filter
add action=accept chain=input comment="default configuration" disabled=no
protocol=icmp
add action=accept chain=input comment="default configuration"
connection-state=established disabled=no
add action=accept chain=output comment="default configuration" disabled=no
dst-port=123 protocol=udp
add action=accept chain=input comment="default configuration"
connection-state=related disabled=no
add action=accept chain=input comment="Allow Management from Tolt MNS"
disabled=no dst-port=161 protocol=udp src-address=\
216.x.x.x/29
add action=accept chain=input disabled=no dst-port=22,80,443,8291 protocol=tcp
src-address=216.x.x.x/29
add action=accept chain=input disabled=no dst-port=22,80,443,8291 protocol=tcp
src-address=68.x.x.x/26
add action=accept chain=input disabled=no dst-port=22,80,443,8291 protocol=tcp
src-address=68.x.x.x
add action=accept chain=input disabled=no dst-port=22,80,443,8291 protocol=tcp
src-address=216.x.x.x/20
add action=accept chain=input disabled=no dst-port=22,80,443,8291 protocol=tcp
src-address=216.x.x.x/24
add action=accept chain=input disabled=no dst-port=22,80,443,8291 protocol=tcp
src-address=68.x.x.x/26
add action=drop chain=input comment="default configuration" disabled=no
in-interface=bridge1
/ip firewall service-port
set ftp disabled=no ports=21
set tftp disabled=no ports=69
set irc disabled=no ports=6667
set h323 disabled=no
set sip disabled=no ports=5060,5061 sip-direct-media=yes
set pptp disabled=no
/ip hotspot service-port
set ftp disabled=no ports=21
/ip ipsec peer
add address=216.x.x.x/32 auth-method=pre-shared-key dh-group=modp1024
disabled=no dpd-interval=1m dpd-maximum-failures=2 \
enc-algorithm=3des exchange-mode=aggressive generate-policy=no
hash-algorithm=sha1 lifebytes=0 lifetime=10h my-id-user-fqdn=\
[email protected] nat-traversal=yes port=500 proposal-check=obey secret=\
xxxxxxxxxxxxxxxxxxxx send-initial-contact=yes
/ip ipsec policy
add action=encrypt disabled=no dst-address=216.x.x.x/29 dst-port=any
ipsec-protocols=esp level=require priority=0 proposal=\
juniper protocol=all sa-dst-address=216.x.x.x sa-src-address=0.0.0.0
src-address=5.x.x.x/32 src-port=any tunnel=yes
/ip neighbor discovery
set ether1 disabled=no
set ether2 disabled=no
set ether3 disabled=no
set ether4 disabled=no
set ether5 disabled=no
set loopback1 disabled=no
set bridge1 disabled=no
/ip proxy
set always-from-cache=no cache-administrator=webmaster cache-hit-dscp=4
cache-on-disk=no enabled=no max-cache-size=unlimited \
max-client-connections=600 max-fresh-time=3d max-server-connections=600
parent-proxy=0.0.0.0 parent-proxy-port=0 port=8080 \
serialize-connections=no src-address=0.0.0.0
/ip route
add check-gateway=ping disabled=no distance=1 dst-address=0.0.0.0/0
gateway=68.x.x.x pref-src=68.x.x.x scope=30 \
target-scope=10
/ip service
set telnet address="" disabled=yes port=23
set ftp address="" disabled=no port=21
set www address="" disabled=no port=80
set ssh address="" disabled=no port=22
set www-ssl address="" certificate=none disabled=yes port=443
set api address="" disabled=yes port=8728
set winbox address="" disabled=no port=8291
/ip smb
set allow-guests=yes comment=MikrotikSMB domain=MSHOME enabled=no interfaces=all
/ip smb shares
set [ find default=yes ] comment="default share" directory=/pub disabled=no
max-sessions=10 name=pub
/ip smb users
set [ find default=yes ] disabled=no name=guest password="" read-only=yes
/ip socks
set connection-idle-timeout=2m enabled=no max-connections=200 port=1080
/ip traffic-flow
set active-flow-timeout=30m cache-entries=4k enabled=no
inactive-flow-timeout=15s interfaces=all
/ip upnp
set allow-disable-external-interface=yes enabled=no show-dummy-rule=yes
/ipv6 nd
set [ find default=yes ] advertise-dns=no advertise-mac-address=yes disabled=no
hop-limit=unspecified interface=all \
managed-address-configuration=no mtu=unspecified other-configuration=no
ra-delay=3s ra-interval=3m20s-10m ra-lifetime=30m \
reachable-time=unspecified retransmit-interval=unspecified
/ipv6 nd prefix default
set autonomous=yes preferred-lifetime=1w valid-lifetime=4w2d
/port firmware
set directory=firmware ignore-directip-modem=no
/ppp aaa
set accounting=yes interim-update=0s use-radius=no
/queue interface
set ether1 queue=only-hardware-queue
set ether2 queue=only-hardware-queue
set ether3 queue=only-hardware-queue
set ether4 queue=only-hardware-queue
set ether5 queue=only-hardware-queue
/radius incoming
set accept=no port=3799
/routing bfd interface
set [ find default=yes ] disabled=no interface=all interval=0.2s min-rx=0.2s
multiplier=5
/routing mme
set bidirectional-timeout=2 gateway-class=none gateway-keepalive=1m
gateway-selection=no-gateway origination-interval=5s \
preferred-gateway=0.0.0.0 timeout=1m ttl=50
/routing rip
set distribute-default=never garbage-timer=2m metric-bgp=1 metric-connected=1
metric-default=1 metric-ospf=1 metric-static=1 \
redistribute-bgp=no redistribute-connected=no redistribute-ospf=no
redistribute-static=no routing-table=main timeout-timer=3m \
update-timer=30s
/routing ripng
set distribute-default=never garbage-timer=2m metric-bgp=1 metric-connected=1
metric-default=1 metric-ospf=1 metric-static=1 \
redistribute-bgp=no redistribute-connected=no redistribute-ospf=no
redistribute-static=no timeout-timer=3m update-timer=30s
/snmp
set contact=Tolt_MNS enabled=yes engine-id="" location="Irvine, CA"
trap-community=xxxxxxx trap-generators="" trap-target=\
"" trap-version=2
/system clock
set time-zone-name=America/Los_Angeles
/system clock manual
set dst-delta=+00:00 dst-end="jan/01/1970 00:00:00" dst-start="jan/01/1970
00:00:00" time-zone=+00:00
/system identity
set name=Tolt_MNS_Lab-5.3.0.3
/system logging
set 0 action=memory disabled=no prefix="" topics=info
set 1 action=memory disabled=no prefix="" topics=error
set 2 action=memory disabled=no prefix="" topics=warning
set 3 action=echo disabled=no prefix="" topics=critical
/system note
set note="This System is the Property of xxxxxxx If you are not Authorized to
access this system, Please disconnect Immed\
iately!" show-at-login=yes
/system ntp client
set enabled=yes mode=unicast primary-ntp=173.230.144.109
secondary-ntp=128.138.141.171
/system ntp server
set broadcast=no broadcast-addresses="" enabled=no manycast=yes multicast=no
/system resource irq
set 0 cpu=auto
/system routerboard settings
set boot-device=nand-if-fail-then-ethernet boot-protocol=bootp
cpu-frequency=400MHz force-backup-booter=no silent-boot=no
/system scheduler
add disabled=no interval=10s name=schedule1 on-event=ping-vpn policy=\
ftp,reboot,read,write,policy,test,winbox,password,sniff,sensitive,api
start-time=startup
/system script
add name=ping-vpn
policy=ftp,reboot,read,write,policy,test,winbox,password,sniff,sensitive,api
source=\
":put [/ping interface=loopback1 216.x.x.x count=3]"
add name=email-reboots
policy=ftp,reboot,read,write,policy,test,winbox,password,sniff,sensitive,api
source=":while ( [:pick [/syst\
em clock get date] 7 11]<\"2003\" ) do={ :delay 10s }\r\
\n/log info \"time updated; uptime: \$[/system resource get uptime]\"\r\
\n:local es \"\$[/system identity get name] rebooted on \$[/system clock
get date] \$[/system clock get time]\"\r\
\n:delay 90s\r\
\n:local eb \"Log contents (with 90 seconds delay):\\r\\n\"\r\
\n:foreach le in=[/log print as-value] do={\r\
\n :set eb \"\$eb\$[:pick [:tostr [:pick \$le 1]] 5 100] \$[:pick [:tostr
[:pick \$le 2]] 7 100]: \$[:pick [:tostr [:pick \$l\
e 3]] 8 1000]\\r\\n\"\r\
\n}"
/system upgrade mirror
set check-interval=1d enabled=no primary-server=0.0.0.0
secondary-server=0.0.0.0 user=""
/system watchdog
set auto-send-supout=no automatic-supout=yes no-ping-delay=5m
watch-address=none watchdog-timer=yes
/tool bandwidth-server
set allocate-udp-ports-from=2000 authenticate=yes enabled=yes max-sessions=100
/tool e-mail
set address=0.0.0.0 from=<> password="" port=25 starttls=no user=""
/tool graphing
set page-refresh=300 store-every=5min
/tool mac-server
set [ find default=yes ] disabled=yes interface=all
add disabled=no interface=ether2
add disabled=no interface=ether3
add disabled=no interface=ether4
add disabled=no interface=ether5
/tool mac-server mac-winbox
set [ find default=yes ] disabled=no interface=all
add disabled=no interface=ether1
add disabled=no interface=ether2
add disabled=no interface=ether3
add disabled=no interface=ether4
add disabled=no interface=ether5
/tool mac-server ping
set enabled=yes
/tool sms
set allowed-number="" channel=0 keep-max-sms=0 receive-enabled=no secret=""
/tool sniffer
set file-limit=1000KiB file-name="" filter-ip-address="" filter-ip-protocol=""
filter-mac-address="" filter-mac-protocol="" \
filter-port="" filter-stream=yes interface=all memory-limit=500KiB
memory-scroll=yes only-headers=no streaming-enabled=no \
streaming-server=0.0.0.0
/tool traffic-generator
set latency-distribution-scale=10 test-id=0
/user aaa
set accounting=yes default-group=read exclude-groups="" interim-update=0s
use-radius=no
-------------- next part --------------
An HTML attachment was scrubbed...
URL:
<http://mail.butchevans.com/pipermail/mikrotik/attachments/20141106/e47f09e4/attachment.html>
_______________________________________________
Mikrotik mailing list
[email protected]
http://mail.butchevans.com/mailman/listinfo/mikrotik
Visit http://blog.butchevans.com/ for tutorials related to Mikrotik RouterOS
