D-Link DWL-G520 not configured

[=?koi8-r?B?4czFy9PFyiDzwcTeycvP1w==?=]

Hi All!
I just install snapshot OpenBSD 3.7 and see that my D-Link DWL-G520 wireless
card detected by kernel:
/*dmesg output*/
# dmesg
OpenBSD 3.7-current (GENERIC) #110: Mon May  2 20:07:58 MDT 2005
    [EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Celeron ("GenuineIntel" 686-class, 128KB L2 cache) 468 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem  = 268001280 (261720K)
avail mem = 237731840 (232160K)
using 3297 buffers containing 13504512 bytes (13188K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(54) BIOS, date 03/15/00, BIOS32 rev. 0 @ 0xf06c0
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xf22
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xf0e80/160 (8 entries)
pcibios0: PCI Interrupt Router at 000:04:0 ("Intel 82371FB ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "Intel 82443BX AGP" rev 0x03
ppb0 at pci0 dev 1 function 0 "Intel 82443BX AGP" rev 0x03
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "ATI Rage Fury" rev 0x00
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 4 function 0 "Intel 82371AB PIIX4 ISA" rev 0x02
pciide0 at pci0 dev 4 function 1 "Intel 82371AB IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <IBM-DTLA-307015>
wd0: 16-sector PIO, LBA, 14649MB, 30003120 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
wdc_atapi_intr: warning: reading only 0 of 36 bytes
sd0 at scsibus0 targ 0 lun 0: <, , > SCSI0 0/direct fixed
sd0: drive offline
sd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 4 function 2 "Intel 82371AB USB" rev 0x01: irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
"Intel 82371AB Power Mgmt" rev 0x02 at pci0 dev 4 function 3 not configured
rl0 at pci0 dev 11 function 0 "D-Link Systems 530TX+" rev 0x10: irq 10 address
00:05:5d:49:d9:7d
rlphy0 at rl0 phy 0: RTL internal phy
ath0 at pci0 dev 14 function 0 "Atheros AR5212" rev 0x01: irq 5
ath0: mac 112.9 phy 4.5 radio 5.6 5.6, 802.11a/b/gath0: no valid channels for
regdomain NONE(32976)
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard, using
wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask eb65 netmask ef65 ttymask ffe7
pctr: 686-class user-level performance counters enabled
mtrr: Pentium Pro MTRR support
dkcsum: wd0 matched BIOS disk 80
dkcsum: read of sd0 failed (0)
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
/*end*/
, but if I give a command
#ifconfig ath0 192.168.1.1 255.255.255.0
system responded
ifconfig: SIOCGIFFLAGS: Device not configured
#
what shall I do?
Help please.
Alexey