I've been trying to install OpenBSD 3.7 in a freshly-purchased machine
and after an apparently successful install the boot hangs after
displaying the following:
--------------------------------------
pctr: user-level cycle counter enabled
wd0(pciide0:0:0): timeout
type: ata
c_bcount: 512
c_skip: 0
pciide0:0:0: bus-master DMA error: missing interrupt, status=0x21
--------------------------------------
attempts to boot using -c fail, user input is not accepted at the UKC>
prompt.
hardware failure is possible, suggestions for eliminating that are
welcome.
Thank you for your time,
Mike Califf
[EMAIL PROTECTED]
dmesg follows:
OpenBSD 3.7-current (RAMDISK) #716: Thu Jul 7 16:00:47 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/RAMDISK
cpu0: AMD Sempron(tm) Processor 2600+ ("AuthenticAMD" 686-class, 128KB
L2 cache) 1.60 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2
real mem = 234397696 (228904K)
avail mem = 209657856 (204744K)
using 2886 buffers containing 11821056 bytes (11544K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(e1) BIOS, date 03/02/05, BIOS32 rev. 0 @
0xfb4c0
apm0 at bios0: Power Management spec V1.2
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdef4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfde50/160 (8 entries)
pcibios0: PCI Exclusive IRQs: 3 5 9 10 11
pcibios0: PCI Interrupt Router at 000:02:0 ("SIS 85C503 System" rev
0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x8000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "SIS 760 PCI" rev 0x03
ppb0 at pci0 dev 1 function 0 "SIS 86C202 VGA" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "SIS 6330 VGA" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
pcib0 at pci0 dev 2 function 0 "SIS 964 PCI" rev 0x36
pciide0 at pci0 dev 2 function 5 "SIS 5513 EIDE" rev 0x01: 760: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <Maxtor 6E040L0>
wd0: 16-sector PIO, LBA, 39205MB, 80293248 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 6
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <LITE-ON, CD-ROM LTN-529S, 7S56> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
"SIS 7012 AC97" rev 0xa0 at pci0 dev 2 function 7 not configured
"SIS 5597/5598 USB" rev 0x0f at pci0 dev 3 function 0 not configured
"SIS 5597/5598 USB" rev 0x0f at pci0 dev 3 function 1 not configured
"SIS 5597/5598 USB" rev 0x0f at pci0 dev 3 function 2 not configured
"SIS 7002 USB" rev 0x00 at pci0 dev 3 function 3 not configured
pciide1 at pci0 dev 5 function 0 "SIS 180 SATA" rev 0x01: DMA
pciide1: using irq 11 for native-PCI interrupt
rl0 at pci0 dev 9 function 0 "D-Link Systems 530TX+" rev 0x10: irq 11
address 00:11:95:26:90:1e
rlphy0 at rl0 phy 0: RTL internal phy
rl1 at pci0 dev 11 function 0 "D-Link Systems 530TX+" rev 0x10: irq 5
address 00:11:95:26:8e:a7
rlphy1 at rl1 phy 0: RTL internal phy
rl2 at pci0 dev 13 function 0 "Realtek 8139" rev 0x10: irq 10 address
00:11:5b:f1:d2:ac
rlphy2 at rl2 phy 0: RTL internal phy
pchb1 at pci0 dev 24 function 0 "AMD AMD64 HyperTransport" rev 0x00
pchb2 at pci0 dev 24 function 1 "AMD AMD64 Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 DRAM Cfg" rev 0x00
pchb4 at pci0 dev 24 function 3 "AMD AMD64 Misc Cfg" rev 0x00
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask fbcd netmask ffed ttymask ffef
rd0: fixed, 3800 blocks
root on rd0a
rootdev=0x1100 rrootdev=0x2f00 rawdev=0x2f02
