Hello OpenBSD fans,
I have problems with eap(4) driver. I have two CT5880
cards of different manufacturers placed in different computers. The
problem arises only with one sound
card.
The computer with this card, works fine:
eap0 at pci0 dev 10 function 0 "Ensoniq CT5880" rev 0x02: irq 5
ac97: codec id 0x83847609 (SigmaTel STAC9721/23)
ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at eap0
midi0 at eap0: <AudioPCI MIDI UART>
The computer with this one, plays distorted sound:
eap0 at pci0 dev 9 function 0 "Ensoniq CT5880" rev 0x02: irq 10
ac97: codec id 0x54524123 (TriTech Microelectronics TR28602)
audio0 at eap0
midi0 at eap0: <AudioPCI MIDI UART>
Both sound cards work ok with Linux, so I guess it is not a hardware
problem .
If you need further information, I will be pleased to provide it
Thanks for your time.
Ramiro.
I attach below the full dmesg outputs:
***************** right one *******************************
OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Athlon(tm) processor ("AuthenticAMD" 686-class) 1.20 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR
real mem = 267952128 (261672K)
avail mem = 237600768 (232032K)
using 3296 buffers containing 13500416 bytes (13184K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(9c) BIOS, date 11/30/01, BIOS32 rev. 0 @ 0xfb1f0
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb670
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdc00/160 (8 entries)
pcibios0: PCI Exclusive IRQs: 5 9 10 11
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0xa800
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "VIA VT8363 Host" rev 0x03
ppb0 at pci0 dev 1 function 0 "VIA VT8363 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "Nvidia Vanta" rev 0x15
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C686 ISA" rev 0x40
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x06: ATA100,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <ST340810A>
wd0: 16-sector PIO, LBA, 38166MB, 78165360 sectors
wd1 at pciide0 channel 0 drive 1: <Conner Peripherals 1080MB - CFS1081A>
wd1: 16-sector PIO, LBA, 1032MB, 2114180 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1(pciide0:0:1): using PIO mode 4, DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVD-ROM GDR8161B, 0102> SCSI0
5/cdrom removable
atapiscsi1 at pciide0 channel 1 drive 1
scsibus1 at atapiscsi1: 2 targets
cd1 at scsibus1 targ 0 lun 0: <HL-DT-ST, DVDRAM GSA-4160B, A302> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
cd1(pciide0:1:1): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x1a: irq 9
usb0 at uhci0: USB revision 1.0
uhub0 at usb0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1 at pci0 dev 7 function 3 "VIA VT83C572 USB" rev 0x1a: irq 9
usb1 at uhci1: USB revision 1.0
uhub1 at usb1
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
viaenv0 at pci0 dev 7 function 4 "VIA VT82C686 SMBus" rev 0x40
eap0 at pci0 dev 10 function 0 "Ensoniq CT5880" rev 0x02: irq 5
ac97: codec id 0x83847609 (SigmaTel STAC9721/23)
ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at eap0
midi0 at eap0: <AudioPCI MIDI UART>
rl0 at pci0 dev 11 function 0 "Realtek 8139" rev 0x10: irq 11 address
00:02:44:59:f1:70
rlphy0 at rl0 phy 0: RTL internal phy
bktr0 at pci0 dev 14 function 0 "Brooktree BT878" rev 0x11: irq 5
bktr0: Askey/Dynalink Magic TView, Temic NTSC tuner.
"Brooktree BT878 Audio" rev 0x11 at pci0 dev 14 function 1 not configured
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard, using
wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask e765 netmask ef65 ttymask ffe7
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
wd0: no disk label
dkcsum: wd0 matched BIOS disk 80
dkcsum: wd1 matched BIOS disk 81
root on wd1a
rootdev=0x10 rrootdev=0x310 rawdev=0x312
cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x0
SENSE KEY: Not Ready
ASC/ASCQ: Medium Not Present
cd0(atapiscsi0:0:0): Check Condition (error 0x70) on opcode 0x0
SENSE KEY: Not Ready
ASC/ASCQ: Medium Not Present
umass0 at uhub0 port 2 configuration 1 interface 0
umass0: vendor 0x0457 USB Mass Storage Device, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus2 at umass0: 2 targets
sd0 at scsibus2 targ 1 lun 0: <USB 2.0, Flash Disk, 0.00> SCSI2 0/direct
removable
sd0: 250MB, 250 cyl, 64 head, 32 sec, 512 bytes/sec, 512000 sec total
***************** right one *******************************
***************** bad one *******************************
OpenBSD 3.7 (GENERIC) #50: Sun Mar 20 00:01:57 MST 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Intel Pentium (P54C) ("GenuineIntel" 586-class) 133 MHz
cpu0: FPU,V86,DE,PSE,TSC,MSR,MCE,CX8
cpu0: F00F bug workaround installed
real mem = 49913856 (48744K)
avail mem = 37871616 (36984K)
using 634 buffers containing 2596864 bytes (2536K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(dd) BIOS, date 06/21/96, BIOS32 rev. 0 @ 0xfb230
apm0 at bios0: Power Management spec V1.2
apm0: APM engage (device 1): power management disabled (1)
apm0: AC on, battery charge unknown, estimated 0:00 hours
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb748
pcibios0: PCI BIOS has 5 Interrupt Routing table entries
pcibios0: PCI Interrupt Router at 000:07:0 ("Intel 82371SB ISA" rev 0x00)
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xc0000/0x8000
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "Intel 82437VX" rev 0x02
pcib0 at pci0 dev 7 function 0 "Intel 82371SB ISA" rev 0x01
pciide0 at pci0 dev 7 function 1 "Intel 82371SB IDE" rev 0x00: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <M1614TA>
wd0: 16-sector PIO, LBA, 1040MB, 2131584 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SAMSUNG, CD-ROM SCR-2431, 1.02> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, DMA mode 2
ohci0 at pci0 dev 8 function 0 "NEC USB" rev 0x41: irq 11, version 1.0
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1 at pci0 dev 8 function 1 "NEC USB" rev 0x41: irq 10, version 1.0
usb1 at ohci1: USB revision 1.0
uhub1 at usb1
uhub1: NEC OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ehci0 at pci0 dev 8 function 2 "NEC USB" rev 0x02: irq 9
ehci0: EHCI version 0.95
ehci0: companion controllers, 3 ports each: ohci0 ohci1
usb2 at ehci0: USB revision 2.0
uhub2 at usb2
uhub2: NEC EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: single transaction translator
uhub2: 5 ports with 5 removable, self powered
eap0 at pci0 dev 9 function 0 "Ensoniq CT5880" rev 0x02: irq 10
ac97: codec id 0x54524123 (TriTech Microelectronics TR28602)
audio0 at eap0
midi0 at eap0: <AudioPCI MIDI UART>
vga1 at pci0 dev 10 function 0 "Avance Logic ALG2302" rev 0x00
wsdisplay0 at vga1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0 (mux 1 ignored for console): console keyboard, using
wsdisplay0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: <PC speaker>
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
pccom1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fd0 at fdc0 drive 0: 1.44MB 80 cyl, 2 head, 18 sec
biomask ff65 netmask ff65 ttymask ffe7
pctr: 586-class performance counters and user-level cycle counter enabled
dkcsum: wd0 matched BIOS disk 80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
umass0 at uhub2 port 1 configuration 1 interface 0
umass0: vendor 0x0457 USB Mass Storage Device, rev 2.00/1.00, addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets
sd0 at scsibus1 targ 1 lun 0: <USB 2.0, Flash Disk, 0.00> SCSI2 0/direct
removable
sd0: 250MB, 250 cyl, 64 head, 32 sec, 512 bytes/sec, 512000 sec total
***************** bad one *******************************
