Hello,
is somehow possible to enable jumbo frames on BCM5716? I have applied
patch from Jonathan Gray --
http://marc.info/?l=openbsd-tech&m=130409059829496&w=2
in hope that maybe jumbo frames would work, but it didn't ...
Is jumbo frames somehow realated to brgphy?
# ifconfig bnx1 mtu 9000
ifconfig: SIOCSIFMTU: Invalid argument
# ifconfig bnx1 mtu 1501
ifconfig: SIOCSIFMTU: Invalid argument
dmesg:
bnx0: address 84:2b:2b:6d:37:8b
brgphy0 at bnx0 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
bnx1: address 84:2b:2b:6d:37:8c
brgphy1 at bnx1 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
pcidump:
1:0:0: Broadcom BCM5716
0x0000: Vendor ID: 14e4 Product ID: 163b
0x0004: Command: 0006 Status ID: 0010
0x0008: Class: 02 Subclass: 00 Interface: 00 Revision: 20
0x000c: BIST: 00 Header Type: 80 Latency Timer: 00 Cache Line
Size: 10
0x0010: BAR mem 64bit addr: 0x00000000da000000/0x02000000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 1028 Product ID: 028c
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 01 Line: 0f Min Gnt: 00 Max Lat: 00
0x0048: Capability 0x01: Power Management
0x0050: Capability 0x03: Vital Product Data (VPD)
0x0058: Capability 0x05: Message Signaled Interrupts (MSI)
0x00a0: Capability 0x11: Extended Message Signaled Interrupts
(MSI-X)
0x00ac: Capability 0x10: PCI Express
Link Speed: 2.5 / 2.5 Gb/s Link Width: x4 / x4
1:0:1: Broadcom BCM5716
0x0000: Vendor ID: 14e4 Product ID: 163b
0x0004: Command: 0006 Status ID: 0010
0x0008: Class: 02 Subclass: 00 Interface: 00 Revision: 20
0x000c: BIST: 00 Header Type: 80 Latency Timer: 00 Cache Line
Size: 10
0x0010: BAR mem 64bit addr: 0x00000000dc000000/0x02000000
0x0018: BAR empty (00000000)
0x001c: BAR empty (00000000)
0x0020: BAR empty (00000000)
0x0024: BAR empty (00000000)
0x0028: Cardbus CIS: 00000000
0x002c: Subsystem Vendor ID: 1028 Product ID: 028c
0x0030: Expansion ROM Base Address: 00000000
0x0038: 00000000
0x003c: Interrupt Pin: 02 Line: 0e Min Gnt: 00 Max Lat: 00
0x0048: Capability 0x01: Power Management
0x0050: Capability 0x03: Vital Product Data (VPD)
0x0058: Capability 0x05: Message Signaled Interrupts (MSI)
0x00a0: Capability 0x11: Extended Message Signaled Interrupts
(MSI-X)
0x00ac: Capability 0x10: PCI Express
Link Speed: 2.5 / 2.5 Gb/s Link Width: x4 / x4
OpenBSD 4.9-current (GENERIC.MP) #0: Sun May 1 16:30:10 CEST 2011
r...@rtr1.she.lan:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 6428266496 (6130MB)
avail mem = 6243102720 (5953MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.6 @ 0xcf49c000 (78 entries)
bios0: vendor Dell Inc. version "1.6.3" date 02/07/2011
bios0: Dell Inc. PowerEdge R410
acpi0 at bios0: rev 2
acpi0: sleep states S0 S4 S5
acpi0: tables DSDT FACP APIC SPCR HPET DM__ MCFG WD__ SLIC ERST HEST
BERT EINJ SRAT TCPA SSDT
acpi0: wakeup devices PCI0(S5)
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 32 (boot processor)
cpu0: Intel(R) Xeon(R) CPU E5630 @ 2.53GHz, 2527.31 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES,NXE,LONG
cpu0: 256KB 64b/line 8-way L2 cache
cpu0: apic clock running at 133MHz
cpu1 at mainbus0: apid 34 (application processor)
cpu1: Intel(R) Xeon(R) CPU E5630 @ 2.53GHz, 2527.00 MHz
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES,NXE,LONG
cpu1: 256KB 64b/line 8-way L2 cache
cpu2 at mainbus0: apid 50 (application processor)
cpu2: Intel(R) Xeon(R) CPU E5630 @ 2.53GHz, 2527.00 MHz
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES,NXE,LONG
cpu2: 256KB 64b/line 8-way L2 cache
cpu3 at mainbus0: apid 52 (application processor)
cpu3: Intel(R) Xeon(R) CPU E5630 @ 2.53GHz, 2527.00 MHz
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,SBF,SSE3,PCLMUL,MWAIT,DS-CPL,VMX,SMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,DCA,SSE4.1,SSE4.2,POPCNT,AES,NXE,LONG
cpu3: 256KB 64b/line 8-way L2 cache
ioapic0 at mainbus0: apid 0 pa 0xfec00000, version 20, 24 pins
ioapic1 at mainbus0: apid 1 pa 0xfec80000, version 20, 24 pins
ioapic1: misconfigured as apic 0, remapped to apid 1
acpihpet0 at acpi0: 14318179 Hz
acpimcfg0 at acpi0 addr 0xe0000000, bus 0-255
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus 1 (PEX1)
acpiprt2 at acpi0: bus 2 (PEX3)
acpiprt3 at acpi0: bus 3 (PEX7)
acpiprt4 at acpi0: bus -1 (PEX9)
acpiprt5 at acpi0: bus -1 (PEXA)
acpiprt6 at acpi0: bus -1 (SBEX)
acpiprt7 at acpi0: bus 4 (COMP)
acpicpu0 at acpi0: C3, C1
acpicpu1 at acpi0: C3, C1
acpicpu2 at acpi0: C3, C1
acpicpu3 at acpi0: C3, C1
ipmi at mainbus0 not configured
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel 5500 Host" rev 0x13
ppb0 at pci0 dev 1 function 0 "Intel X58 PCIE" rev 0x13
pci1 at ppb0 bus 1
bnx0 at pci1 dev 0 function 0 "Broadcom BCM5716" rev 0x20: apic 1 int 4
bnx1 at pci1 dev 0 function 1 "Broadcom BCM5716" rev 0x20: apic 1 int 16
ppb1 at pci0 dev 3 function 0 "Intel X58 PCIE" rev 0x13
pci2 at ppb1 bus 2
mpi0 at pci2 dev 0 function 0 "Symbios Logic SAS1068E" rev 0x08: apic 1
int 0
scsibus0 at mpi0: 112 targets
sd0 at scsibus0 targ 0 lun 0: <Dell, VIRTUAL DISK, 1028> SCSI3 0/direct
fixed naa.600508e0000000002a7749fd24f2d10d
sd0: 139392MB, 512 bytes/sec, 285474816 sec total
ses0 at scsibus0 targ 8 lun 0: <DP, BACKPLANE, 1.07> SCSI3 13/enclosure
services fixed t10.DP______BACKPLANE000000
ppb2 at pci0 dev 7 function 0 "Intel X58 PCIE" rev 0x13: apic 1 int 21
pci3 at ppb2 bus 3
ix0 at pci3 dev 0 function 0 "Intel 10GbE SFP+ (82599)" rev 0x01: apic 1
int 6, address 00:1b:21:9e:6c:98
ix1 at pci3 dev 0 function 1 "Intel 10GbE SFP+ (82599)" rev 0x01: apic 1
int 13, address 00:1b:21:9e:6c:99
"Intel X58 Misc" rev 0x13 at pci0 dev 20 function 0 not configured
"Intel X58 GPIO" rev 0x13 at pci0 dev 20 function 1 not configured
"Intel X58 RAS" rev 0x13 at pci0 dev 20 function 2 not configured
uhci0 at pci0 dev 26 function 0 "Intel 82801JI USB" rev 0x00: apic 0 int 17
uhci1 at pci0 dev 26 function 1 "Intel 82801JI USB" rev 0x00: apic 0 int 18
ehci0 at pci0 dev 26 function 7 "Intel 82801JI USB" rev 0x00: apic 0 int 19
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
uhci2 at pci0 dev 29 function 0 "Intel 82801JI USB" rev 0x00: apic 0 int 21
uhci3 at pci0 dev 29 function 1 "Intel 82801JI USB" rev 0x00: apic 0 int 20
uhci4 at pci0 dev 29 function 2 "Intel 82801JI USB" rev 0x00: apic 0 int 21
uhci5 at pci0 dev 29 function 3 "Intel 82801JI USB" rev 0x00: apic 0 int 20
ehci1 at pci0 dev 29 function 7 "Intel 82801JI USB" rev 0x00: apic 0 int 21
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1
ppb3 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0x90
pci4 at ppb3 bus 4
vga1 at pci4 dev 3 function 0 "Matrox MGA G200eW" rev 0x0a
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 31 function 0 "Intel 82801JIR LPC" rev 0x00
pciide0 at pci0 dev 31 function 2 "Intel 82801JI SATA" rev 0x00: DMA,
channel 0 configured to native-PCI, channel 1 configured to native-PCI
pciide0: using apic 0 int 23 for native-PCI interrupt
pciide1 at pci0 dev 31 function 5 "Intel 82801JI SATA" rev 0x00: DMA,
channel 0 wired to native-PCI, channel 1 wired to native-PCI
pciide1: using apic 0 int 22 for native-PCI interrupt
atapiscsi0 at pciide1 channel 0 drive 0
scsibus1 at atapiscsi0: 2 targets
cd0 at scsibus1 targ 0 lun 0: <TEAC, DVD-ROM DV-28SW, R.2A> ATAPI
5/cdrom removable
cd0(pciide1:0:0): using PIO mode 4, Ultra-DMA mode 5
usb2 at uhci0: USB revision 1.0
uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb3 at uhci1: USB revision 1.0
uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb4 at uhci2: USB revision 1.0
uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb5 at uhci3: USB revision 1.0
uhub5 at usb5 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb6 at uhci4: USB revision 1.0
uhub6 at usb6 "Intel UHCI root hub" rev 1.00/1.00 addr 1
usb7 at uhci5: USB revision 1.0
uhub7 at usb7 "Intel UHCI root hub" rev 1.00/1.00 addr 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
mtrr: Pentium Pro MTRR support
uhub8 at uhub0 port 3 "Standard Microsystems product 0x2514" rev
2.00/0.00 addr 2
uhidev0 at uhub4 port 2 configuration 1 interface 0 "Avocent USB
Composite Device-0" rev 1.10/0.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 modifier keys, 6 key codes
wskbd1 at ukbd0 mux 1
wskbd1: connecting to wsdisplay0
uhidev1 at uhub4 port 2 configuration 1 interface 1 "Avocent USB
Composite Device-0" rev 1.10/0.00 addr 2
uhidev1: iclass 3/1
ums0 at uhidev1: 3 buttons, Z dir
wsmouse0 at ums0 mux 0
vscsi0 at root
scsibus2 at vscsi0: 256 targets
softraid0 at root
root on sd0a (e4d29879217cfa0b.a) swap on sd0b dump on sd0b
bnx0: address 84:2b:2b:6d:37:8b
brgphy0 at bnx0 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
bnx1: address 84:2b:2b:6d:37:8c
brgphy1 at bnx1 phy 1: BCM5709 10/100/1000baseT PHY, rev. 8
--
/hrvoje
