Dear misc users,
I'm currenlty installing openBSD on a ALix board, the network card are
RhineIII
I may have detect a 'bug':
- the network paquet are send only when vr1 is plugged, not vr0.
as soon as you plug / unplug vr1 the network start / stop on both interface.
Is ukphy experimental ??
Or is it just a specific configuration to set up ?
Regards,
Sven.
dmesg part :
<<
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10,
address 00 :0d:b9:1c:73:cc
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11,
address 0 0:0d:b9:1c:73:cd
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
>>
full dmesg:
<<
OpenBSD 4.9 (GENERIC) #671: Wed Mar 2 07:09:00 MST 2011
[email protected]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class)
499 MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 268009472 (255MB)
avail mem = 253493248 (241MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/05/08, BIOS32 rev. 0 @ 0xfd088
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xe0000/0xa800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10,
address 00:0d:b9:1c:73:cc
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
vr1 at pci0 dev 10 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 11,
address 00:0d:b9:1c:73:cd
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI
0x004063, model 0x0034
athn0 at pci0 dev 12 function 0 "Atheros AR9280" rev 0x01: irq 9
athn0: AR9280 rev 2 (2T2R), ROM rev 21, address 00:0b:6b:02:10:2a
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFX3-2048>
wd0: 4-sector PIO, LBA, 1953MB, 4001760 sectors
wd0(pciide0:0:0): using PIO mode 4, DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 12, version
1.0, legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 12
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
biomask f1e7 netmask ffe7 ttymask ffff
mtrr: K6-family MTRR support (2 registers)
nvram: invalid checksum
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
root on wd0a swap on wd0b dump on wd0b
clock: unknown CMOS layout
>>
--
---------------------------------------------------------------------------------------------------------------------
() ascii ribbon campaign - against html e-mail
/\
