See iwi(4) manpage, FILES section.
On 2012-01-18, Wesley M. <[email protected]> wrote:
> I use OpenBSD 5.0 RELEASE on a notebook : twinhead F12DT
>
> There was a
> problem at startup, it hangs on MTRR pentium message.
> So i disabled acpi
> using config -ef /bsd
> Now i can boot.
>
> I'm trying to configure iwi0
> interface.
>
> Wifi card : Intel PRO/Wireless 2200BG
>
> When i try ifconfig iwi0
>:
> iwi0: flags=8802 mtu 1500
> lladdr 00:15:00:48:e6:32
> priority: 4
> groups:
> wlan
> media: IEEE802.11 autoselect
> status: no network
> ieee80211: nwid ""
> 100dBm
> inet6 fe80::215:ff:fe48:e632%iwi0 prefixlen 64 scopeid 0x1
>
> When i
> try ifconfig iwi0 scan :
> iwi0: error 2, could not read firmware iwi-bss
>
> I
> try also wiconfig (http://home.melameth.com/~daniel/pub/wiconfig) provided
> by Daniel M.
> Same error : iwi0: error 2, could not read firmware iwi-bss
>
>
> Any idea ?
> Thank you very much.
>
> Cheers,
>
> Wesley MOUEDINE
> ASSABY
> www.mouedine.net
>
> The dmesg :
>
> OpenBSD 5.0 (GENERIC) #43: Wed Aug
> 17 10:10:52 MDT 2011
>
> [email protected]:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0:
> Intel(R) Pentium(R) M processor 1.73GHz ("GenuineIntel" 686-class) 1.73
> GHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,EST,TM2
> real
> mem = 250998784 (239MB)
> avail mem = 236851200 (225MB)
> User Kernel
> Config
> UKC> disqb^H ^H^H ^Hable qcpi^H ^H^H ^H^H ^H^H ^Hacpi
> 466 acpi0
> disabled
> UKC> a^H ^Hquit
> Continuing...
> mainbus0 at root
> bios0 at mainbus0:
> AT/286+ BIOS, date 03/14/06, BIOS32 rev. 0 @ 0xf0010, SMBIOS rev. 2.3 @
> 0xfb920 (48 entries)
> bios0: vendor American Megatrends Inc. version
> "080011" date 03/14/2006
> bios0: Twinhead F12D
> apm0 at bios0: Power
> Management spec V1.2
> acpi at bios0 function 0x0 not configured
> mpbios0 at
> bios0: Intel MP Specification 1.4
> cpu0 at mainbus0: apid 0 (boot
> processor)
> cpu0: apic clock running at 132MHz
> mpbios0: bus 0 is type PCI
>
> mpbios0: bus 1 is type PCI
> mpbios0: bus 2 is type PCI
> mpbios0: bus 3 is
> type ISA
> ioapic0 at mainbus0: apid 1 pa 0xfec00000, version 20, 24
> pins
> pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
> pcibios0: PCI IRQ Routing
> Table rev 1.0 @ 0xf47b0/272 (15 entries)
> pcibios0: PCI Interrupt Router at
> 000:31:0 ("Intel 82801FBM LPC" rev 0x00)
> pcibios0: PCI bus #2 is the last
> bus
> bios0: ROM list: 0xc0000/0xf000! 0xcf000/0x1000 0xd0000/0x1000
> cpu0:
> Enhanced SpeedStep 1730 MHz: speeds: 1733, 1333, 1067, 800 MHz
> pci0 at
> mainbus0 bus 0: configuration mode 1 (bios)
> pchb0 at pci0 dev 0 function 0
> "Intel 82915GM Host" rev 0x04
> vga1 at pci0 dev 2 function 0 "Intel 82915GM
> Video" rev 0x04
> wsdisplay0 at vga1 mux 1: console (80x25, vt100
> emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
> intagp0 at
> vga1
> agp0 at intagp0: aperture at 0xd0000000, size 0x10000000
> inteldrm0 at
> vga1: apic 1 int 16
> drm0 at inteldrm0
> "Intel 82915GM Video" rev 0x04 at
> pci0 dev 2 function 1 not configured
> uhci0 at pci0 dev 29 function 0 "Intel
> 82801FB USB" rev 0x04: apic 1 int 23
> uhci1 at pci0 dev 29 function 1 "Intel
> 82801FB USB" rev 0x04: apic 1 int 19
> uhci2 at pci0 dev 29 function 2 "Intel
> 82801FB USB" rev 0x04: apic 1 int 18
> uhci3 at pci0 dev 29 function 3 "Intel
> 82801FB USB" rev 0x04: apic 1 int 16
> ehci0 at pci0 dev 29 function 7 "Intel
> 82801FB USB" rev 0x04: apic 1 int 23
> usb0 at ehci0: USB revision 2.0
> uhub0
> at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1
> ppb0 at pci0 dev 30
> function 0 "Intel 82801BAM Hub-to-PCI" rev 0xd4
> pci1 at ppb0 bus 1
> mem
> address conflict 0xf000000/0x1000
> mem address conflict
> 0xf001000/0x1000
> iwi0 at pci1 dev 4 function 0 "Intel PRO/Wireless 2200BG"
> rev 0x05: apic 1 int 18, address 00:15:00:48:e6:32
> cbb0 at pci1 dev 5
> function 0 "O2 Micro OZ711MP1 CardBus" rev 0x21: apic 1 int 16
> sdhc0 at
> pci1 dev 5 function 2 "O2 Micro OZ711MP1 SDHC" rev 0x01: apic 1 int
> 16
> sdmmc0 at sdhc0
> "O2 Micro OZ711MP1 XDHC" rev 0x01 at pci1 dev 5 function
> 3 not configured
> "O2 Micro Firewire" rev 0x02 at pci1 dev 5 function 4 not
> configured
> rl0 at pci1 dev 6 function 0 "Realtek 8139" rev 0x10: apic 1 int
> 19, address 00:40:45:2a:6e:9d
> rlphy0 at rl0 phy 0: RTL internal
> PHY
> cardslot0 at cbb0 slot 0 flags 0
> cardbus0 at cardslot0: bus 2 device 0
> cacheline 0x0, lattimer 0x40
> pcmcia0 at cardslot0
> auich0 at pci0 dev 30
> function 2 "Intel 82801FB AC97" rev 0x04: apic 1 int 17, ICH6 AC97
> ac97:
> codec id 0x414c4760 (Avance Logic ALC655 rev 0)
> audio0 at auich0
> "Intel
> 82801FB Modem" rev 0x04 at pci0 dev 30 function 3 not configured
> ichpcib0
> at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM
> disabled
> pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x04:
> DMA, channel 0 configured to compatibility, channel 1 configured to
> compatibility
> wd0 at pciide0 channel 0 drive 0:
> wd0: 16-sector PIO, LBA48,
> 38154MB, 78140160 sectors
> atapiscsi0 at pciide0 channel 0 drive 1
> scsibus0
> at atapiscsi0: 2 targets
> cd0 at scsibus0 targ 0 lun 0: ATAPI 5/cdrom
> removable
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode
> 5
> cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
> pciide0: channel 1
> disabled (no drives)
> ichiic0 at pci0 dev 31 function 3 "Intel 82801FB
> SMBus" rev 0x04: apic 1 int 19
> iic0 at ichiic0
> admtemp0 at iic0 addr 0x4c:
> adm1032
> spdmem0 at iic0 addr 0x51: 256MB DDR SDRAM non-parity
> PC2700CL2.5
> usb1 at uhci0: USB revision 1.0
> uhub1 at usb1 "Intel UHCI root
> hub" rev 1.00/1.00 addr 1
> usb2 at uhci1: USB revision 1.0
> uhub2 at usb2
> "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb3 at uhci2: USB revision
> 1.0
> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb4 at uhci3:
> USB revision 1.0
> uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr
> 1
> isa0 at ichpcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at
> pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0:
> console keyboard, using wsdisplay0
> pcppi0 at isa0 port 0x61
> spkr0 at
> pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception
> 16
> mtrr: Pentium Pro MTRR support
> vscsi0 at root
> scsibus1 at vscsi0: 256
> targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> root on wd0a
> (30175f1402e399df.a) swap on wd0b dump on wd0b
>
> OpenBSD 5.0 (GENERIC) #43:
> Wed Aug 17 10:10:52 MDT 2011
>
> [email protected]:/usr/src/sys/arch/i386/compile/GENERIC
> cpu0:
> Intel(R) Pentium(R) M processor 1.73GHz ("GenuineIntel" 686-class) 1.73
> GHz
> cpu0:
> FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,TM,SBF,EST,TM2
> real
> mem = 250998784 (239MB)
> avail mem = 236851200 (225MB)
> mainbus0 at
> root
> bios0 at mainbus0: AT/286+ BIOS, date 03/14/06, BIOS32 rev. 0 @
> 0xf0010, SMBIOS rev. 2.3 @ 0xfb920 (48 entries)
> bios0: vendor American
> Megatrends Inc. version "080011" date 03/14/2006
> bios0: Twinhead F12D
> apm0
> at bios0: Power Management spec V1.2
> acpi at bios0 function 0x0 not
> configured
> mpbios0 at bios0: Intel MP Specification 1.4
> cpu0 at mainbus0:
> apid 0 (boot processor)
> cpu0: apic clock running at 133MHz
> mpbios0: bus 0
> is type PCI
> mpbios0: bus 1 is type PCI
> mpbios0: bus 2 is type PCI
>
> mpbios0: bus 3 is type ISA
> ioapic0 at mainbus0: apid 1 pa 0xfec00000,
> version 20, 24 pins
> pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
> pcibios0:
> PCI IRQ Routing Table rev 1.0 @ 0xf47b0/272 (15 entries)
> pcibios0: PCI
> Interrupt Router at 000:31:0 ("Intel 82801FBM LPC" rev 0x00)
> pcibios0: PCI
> bus #2 is the last bus
> bios0: ROM list: 0xc0000/0xf000! 0xcf000/0x1000
> 0xd0000/0x1000
> cpu0: Enhanced SpeedStep 1730 MHz: speeds: 1733, 1333, 1067,
> 800 MHz
> pci0 at mainbus0 bus 0: configuration mode 1 (bios)
> pchb0 at pci0
> dev 0 function 0 "Intel 82915GM Host" rev 0x04
> vga1 at pci0 dev 2 function
> 0 "Intel 82915GM Video" rev 0x04
> wsdisplay0 at vga1 mux 1: console (80x25,
> vt100 emulation)
> wsdisplay0: screen 1-5 added (80x25, vt100
> emulation)
> intagp0 at vga1
> agp0 at intagp0: aperture at 0xd0000000, size
> 0x10000000
> inteldrm0 at vga1: apic 1 int 16
> drm0 at inteldrm0
> "Intel
> 82915GM Video" rev 0x04 at pci0 dev 2 function 1 not configured
> uhci0 at
> pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x04: apic 1 int 23
> uhci1 at
> pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x04: apic 1 int 19
> uhci2 at
> pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x04: apic 1 int 18
> uhci3 at
> pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x04: apic 1 int 16
> ehci0 at
> pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x04: apic 1 int 23
> usb0 at
> ehci0: USB revision 2.0
> uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00
> addr 1
> ppb0 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev
> 0xd4
> pci1 at ppb0 bus 1
> mem address conflict 0xf000000/0x1000
> mem address
> conflict 0xf001000/0x1000
> iwi0 at pci1 dev 4 function 0 "Intel PRO/Wireless
> 2200BG" rev 0x05: apic 1 int 18, address 00:15:00:48:e6:32
> cbb0 at pci1 dev
> 5 function 0 "O2 Micro OZ711MP1 CardBus" rev 0x21: apic 1 int 16
> sdhc0 at
> pci1 dev 5 function 2 "O2 Micro OZ711MP1 SDHC" rev 0x01: apic 1 int
> 16
> sdmmc0 at sdhc0
> "O2 Micro OZ711MP1 XDHC" rev 0x01 at pci1 dev 5 function
> 3 not configured
> "O2 Micro Firewire" rev 0x02 at pci1 dev 5 function 4 not
> configured
> rl0 at pci1 dev 6 function 0 "Realtek 8139" rev 0x10: apic 1 int
> 19, address 00:40:45:2a:6e:9d
> rlphy0 at rl0 phy 0: RTL internal
> PHY
> cardslot0 at cbb0 slot 0 flags 0
> cardbus0 at cardslot0: bus 2 device 0
> cacheline 0x0, lattimer 0x40
> pcmcia0 at cardslot0
> auich0 at pci0 dev 30
> function 2 "Intel 82801FB AC97" rev 0x04: apic 1 int 17, ICH6 AC97
> ac97:
> codec id 0x414c4760 (Avance Logic ALC655 rev 0)
> audio0 at auich0
> "Intel
> 82801FB Modem" rev 0x04 at pci0 dev 30 function 3 not configured
> ichpcib0
> at pci0 dev 31 function 0 "Intel 82801FBM LPC" rev 0x04: PM
> disabled
> pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x04:
> DMA, channel 0 configured to compatibility, channel 1 configured to
> compatibility
> wd0 at pciide0 channel 0 drive 0:
> wd0: 16-sector PIO, LBA48,
> 38154MB, 78140160 sectors
> atapiscsi0 at pciide0 channel 0 drive 1
> scsibus0
> at atapiscsi0: 2 targets
> cd0 at scsibus0 targ 0 lun 0: ATAPI 5/cdrom
> removable
> wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode
> 5
> cd0(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 2
> pciide0: channel 1
> disabled (no drives)
> ichiic0 at pci0 dev 31 function 3 "Intel 82801FB
> SMBus" rev 0x04: apic 1 int 19
> iic0 at ichiic0
> admtemp0 at iic0 addr 0x4c:
> adm1032
> spdmem0 at iic0 addr 0x51: 256MB DDR SDRAM non-parity
> PC2700CL2.5
> usb1 at uhci0: USB revision 1.0
> uhub1 at usb1 "Intel UHCI root
> hub" rev 1.00/1.00 addr 1
> usb2 at uhci1: USB revision 1.0
> uhub2 at usb2
> "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb3 at uhci2: USB revision
> 1.0
> uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1
> usb4 at uhci3:
> USB revision 1.0
> uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr
> 1
> isa0 at ichpcib0
> isadma0 at isa0
> pckbc0 at isa0 port 0x60/5
> pckbd0 at
> pckbc0 (kbd slot)
> pckbc0: using irq 1 for kbd slot
> wskbd0 at pckbd0:
> console keyboard, using wsdisplay0
> pcppi0 at isa0 port 0x61
> spkr0 at
> pcppi0
> npx0 at isa0 port 0xf0/16: reported by CPUID; using exception
> 16
> mtrr: Pentium Pro MTRR support
> vscsi0 at root
> scsibus1 at vscsi0: 256
> targets
> softraid0 at root
> scsibus2 at softraid0: 256 targets
> root on wd0a
> (30175f1402e399df.a) swap on wd0b dump on wd0b
> umass0 at uhub0 port 2
> configuration 1 interface 0 "Kingston DataTraveler 2.0" rev 2.00/1.10 addr
> 2
> umass0: using SCSI over Bulk-Only
> scsibus3 at umass0: 2 targets,
> initiator 0
> sd0 at scsibus3 targ 1 lun 0: SCSI0 0/direct removable
> serial.13fe1f005B831A000095
> sd0: 7636MB, 512 bytes/sector, 15638528
> sectors
> sd0 detached
> scsibus3 detached
> umass0 detached
> iwi0: error 2, could
> not read firmware iwi-bss
> iwi0: timeout waiting for master
> iwi0: error 2,
> could not read firmware iwi-bss
> iwi0: error 2, could not read firmware
> iwi-bss
> iwi0: error 2, could not read firmware iwi-bss
> iwi0: error 2, could
> not read firmware iwi-bss
> umass0 at uhub0 port 2 configuration 1 interface
> 0 "JetFlash Mass Storage Device" rev 2.00/11.00 addr 2
> umass0: using SCSI
> over Bulk-Only
> scsibus3 at umass0: 2 targets, initiator 0
> sd0 at scsibus3
> targ 1 lun 0: SCSI0 0/direct removable serial.85641000IT7IZ4KWB0DL
> sd0:
> 7728MB, 512 bytes/sector, 15826944 sectors
> sd0 detached
> scsibus3
> detached
> umass0 detached
> iwi0: error 2, could not read firmware
> iwi-bss
> iwi0: error 2, could not read firmware iwi-bss
