I have an alix2d2 running OpenBSD 5.0. There are no hw.sensors.
The producer says there is an LM86 on board, which is supported by the
maxtmp driver. It appears the driver is present in generic. I tried starting
sensorsd but got:
daemon:Feb 17 13:12:04 T1 sensorsd[10445]: startup, system has 0 sensors
How can I read the temperature of my alix2d2 running OpenBSD 5.0?
[15:59:ttyp1][root@T3:~:1]$ sysctl hw
hw.machine=i386
hw.model=Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class)
hw.ncpu=1
hw.byteorder=1234
hw.pagesize=4096
hw.disknames=wd0:c8fc559b0e991404
hw.diskcount=1
hw.cpuspeed=499
hw.physmem=267976704
hw.usermem=267964416
hw.ncpufound=1
hw.allowpowerdown=1
[15:59:ttyp1][root@T3:~:2]$ uname -a
OpenBSD T3.nmi 5.0 GENERIC.MP#59 i386
dmesg:
OpenBSD 5.0 (GENERIC.MP) #59: Wed Aug 17 10:19:44 MDT 2011
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC.MP
cpu0: Geode(TM) Integrated Processor by AMD PCS ("AuthenticAMD" 586-class) 499
MHz
cpu0: FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CFLUSH,MMX
real mem = 267976704 (255MB)
avail mem = 253521920 (241MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 11/05/08, BIOS32 rev. 0 @ 0xfd088
pcibios0 at bios0: rev 2.1 @ 0xf0000/0x10000
pcibios0: pcibios_get_intr_routing - function not supported
pcibios0: PCI IRQ Routing information unavailable.
pcibios0: PCI bus #0 is the last bus
bios0: ROM list: 0xe0000/0xa800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 1 function 0 "AMD Geode LX" rev 0x33
glxsb0 at pci0 dev 1 function 2 "AMD Geode LX Crypto" rev 0x00: RNG AES
vr0 at pci0 dev 9 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 10, address
00:0d:b9:25:8f:ec
ukphy0 at vr0 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
vr1 at pci0 dev 11 function 0 "VIA VT6105M RhineIII" rev 0x96: irq 15, address
00:0d:b9:25:8f:ed
ukphy1 at vr1 phy 1: Generic IEEE 802.3u media interface, rev. 3: OUI 0x004063,
model 0x0034
glxpcib0 at pci0 dev 15 function 0 "AMD CS5536 ISA" rev 0x03: rev 3, 32-bit
3579545Hz timer, watchdog, gpio
gpio0 at glxpcib0: 32 pins
pciide0 at pci0 dev 15 function 2 "AMD CS5536 IDE" rev 0x01: DMA, channel 0
wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <SanDisk SDCFAA-004G>
wd0: 1-sector PIO, LBA48, 3815MB, 7813120 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
ohci0 at pci0 dev 15 function 4 "AMD CS5536 USB" rev 0x02: irq 12, version 1.0,
legacy support
ehci0 at pci0 dev 15 function 5 "AMD CS5536 USB" rev 0x02: irq 12
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "AMD EHCI root hub" rev 2.00/1.00 addr 1
isa0 at glxpcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb1 at ohci0: USB revision 1.0
uhub1 at usb1 "AMD OHCI root hub" rev 1.00/1.00 addr 1
mtrr: K6-family MTRR support (2 registers)
nvram: invalid checksum
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
root on wd0a (c8fc559b0e991404.a) swap on wd0b dump on wd0b
--
Michal Mazurek
