Hi, According to the man page of umsm(4) the "Option GlobeTrotter HSDPA ICON225 USB" is a supported device which is known to work.
I got a device which is recognized by Option as "iCON 225" after entering its serial number on their support homepage (yielding as result http://www.option.com/en/support/software-download/icon225/). So I am pretty sure it is in fact the same device claimed to be supported by umsm(4). After attaching the device I get umsm0 at uhub3 port 1 configuration 1 interface 0 "Option N.V. Globetrotter HSDPA Modem" rev 1.10/0.00 addr 2 umsm0 detached umsm0 at uhub3 port 1 configuration 1 interface 0 "Option N.V. Globetrotter HSDPA Modem" rev 1.10/0.00 addr 2 ucom0 at umsm0 umsm1 at uhub3 port 1 configuration 1 interface 1 "Option N.V. Globetrotter HSDPA Modem" rev 1.10/0.00 addr 2 ucom1 at umsm1 umsm(4) says "The Option GlobeTrotter HSDPA/HSUPA modems have three serial ports, but only the last port can be used to make PPP connections." Unfortunately I see only two serial ports (ucom0 and ucom1) where none of them respond to input nor echo my input (tested with "sudo cu -l /dev/cuaU0" and "sudo cu -l /dev/cuaU1"; ppp(8) does not work either). This is in line with the statement above but the problem is there is no third port detected which is claimed to work! This seems to be the same problem as discussed (but not solved) in http://marc.info/?l=openbsd-misc&m=123457371231119. However there seem to exist devices which report three ports (see e.g. http://www.daemonforums.org/showthread.php?t=6214). Please find attached the full dmesg and output of "usbdevs -v" at the end of this posting. Any hints are highly appreciated. It might also make sense to modify the man page accordingly (i.e., there exist devices which do not work but report under the same device name). Thanks! Best regards, Ingo OpenBSD 5.2-current (GENERIC.MP) #8: Sat Sep 1 19:58:50 MDT 2012 dera...@amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP real mem = 1071579136 (1021MB) avail mem = 1020686336 (973MB) mainbus0 at root bios0 at mainbus0: SMBIOS rev. 2.31 @ 0xdb010 (28 entries) bios0: vendor Hewlett-Packard version "F.34" date 09/20/2005 bios0: Hewlett-Packard Pavilion zd8000 (EL020EA#ABD) acpi0 at bios0: rev 0 acpi0: sleep states S0 S3 S4 S5 acpi0: tables DSDT FACP MCFG APIC BOOT acpi0: wakeup devices LAN_(S4) KBC0(S3) MSE0(S3) acpitimer0 at acpi0: 3579545 Hz, 24 bits acpimcfg0 at acpi0 addr 0xe0000000, bus 0-10 acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: Intel(R) Pentium(R) 4 CPU 3.40GHz, 3391.97 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,CNXT-ID,CX16,xTPR,NXE,LONG cpu0: 2MB 64b/line 8-way L2 cache cpu0: apic clock running at 199MHz cpu1 at mainbus0: apid 1 (application processor) cpu1: Intel(R) Pentium(R) 4 CPU 3.40GHz, 3391.51 MHz cpu1: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,DTES64,MWAIT,DS-CPL,EST,CNXT-ID,CX16,xTPR,NXE,LONG cpu1: 2MB 64b/line 8-way L2 cache ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins acpiprt0 at acpi0: bus 0 (PCI0) acpiprt1 at acpi0: bus 1 (PEG_) acpiprt2 at acpi0: bus 2 (EXP0) acpiprt3 at acpi0: bus 11 (PCIB) acpiec0 at acpi0 acpicpu0 at acpi0 acpicpu1 at acpi0 acpitz0 at acpi0: critical temperature is 81 degC acpibtn0 at acpi0: LID0 acpiac0 at acpi0: AC unit online acpibat0 at acpi0: BAT1 not present acpibtn1 at acpi0: PWRB acpibtn2 at acpi0: SLPB acpivideo0 at acpi0: VGA_ pci0 at mainbus0 bus 0 pchb0 at pci0 dev 0 function 0 "Intel 82915G Host" rev 0x0e ppb0 at pci0 dev 1 function 0 "Intel 82915G PCIE" rev 0x0e: msi pci1 at ppb0 bus 1 vga1 at pci1 dev 0 function 0 "ATI Radeon M241P" rev 0x00 wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) wsdisplay0: screen 1-5 added (80x25, vt100 emulation) radeondrm0 at vga1: apic 2 int 16 drm0 at radeondrm0 ppb1 at pci0 dev 28 function 0 "Intel 82801FB PCIE" rev 0x03: msi pci2 at ppb1 bus 2 uhci0 at pci0 dev 29 function 0 "Intel 82801FB USB" rev 0x03: apic 2 int 23 uhci1 at pci0 dev 29 function 1 "Intel 82801FB USB" rev 0x03: apic 2 int 19 uhci2 at pci0 dev 29 function 2 "Intel 82801FB USB" rev 0x03: apic 2 int 18 uhci3 at pci0 dev 29 function 3 "Intel 82801FB USB" rev 0x03: apic 2 int 16 ehci0 at pci0 dev 29 function 7 "Intel 82801FB USB" rev 0x03: apic 2 int 23 usb0 at ehci0: USB revision 2.0 uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 ppb2 at pci0 dev 30 function 0 "Intel 82801BA Hub-to-PCI" rev 0xd3 pci3 at ppb2 bus 11 cbb0 at pci3 dev 0 function 0 "TI PCI7XX1 CardBus" rev 0x00: apic 2 int 16, CardBus support disabled "TI PCI7XX1 FireWire" rev 0x00 at pci3 dev 0 function 2 not configured "TI PCI7XX1 Flash" rev 0x00 at pci3 dev 0 function 3 not configured sdhc0 at pci3 dev 0 function 4 "TI PCI7XX1 Secure Data" rev 0x00: apic 2 int 16 sdmmc0 at sdhc0 sdmmc1 at sdhc0 sdmmc2 at sdhc0 rl0 at pci3 dev 2 function 0 "Realtek 8139" rev 0x10: apic 2 int 20, address 00:16:36:13:58:7c rlphy0 at rl0 phy 0: RTL internal PHY bwi0 at pci3 dev 3 function 0 "Broadcom BCM4318" rev 0x02: apic 2 int 17, address 00:14:a5:64:e9:68 cardslot0 at cbb0 slot 0 flags 0 pcmcia0 at cardslot0 auich0 at pci0 dev 30 function 2 "Intel 82801FB AC97" rev 0x03: apic 2 int 22, ICH6 AC97 ac97: codec id 0x43585430 (Conexant CXT48) ac97: codec features reserved, headphone, 18 bit DAC, 18 bit ADC, No 3D Stereo audio0 at auich0 "Intel 82801FB Modem" rev 0x03 at pci0 dev 30 function 3 not configured pcib0 at pci0 dev 31 function 0 "Intel 82801FB LPC" rev 0x03 pciide0 at pci0 dev 31 function 1 "Intel 82801FB IDE" rev 0x03: DMA, channel 0 configured to compatibility, channel 1 configured to compatibility wd0 at pciide0 channel 0 drive 0: <TOSHIBA MK1031GAS> wd0: 16-sector PIO, LBA, 95396MB, 195371568 sectors atapiscsi0 at pciide0 channel 0 drive 1 scsibus0 at atapiscsi0: 2 targets cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVD-RW GWA-4082N, CC15> ATAPI 5/cdrom removable wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 cd0(pciide0:0:1): using PIO mode 4, DMA mode 2 pciide0: channel 1 ignored (disabled) ichiic0 at pci0 dev 31 function 3 "Intel 82801FB SMBus" rev 0x03: apic 2 int 19 iic0 at ichiic0 spdmem0 at iic0 addr 0x50: 512MB DDR2 SDRAM non-parity PC2-4200CL3 SO-DIMM spdmem1 at iic0 addr 0x52: 512MB DDR2 SDRAM non-parity PC2-4200CL3 SO-DIMM usb1 at uhci0: USB revision 1.0 uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb2 at uhci1: USB revision 1.0 uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb3 at uhci2: USB revision 1.0 uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 usb4 at uhci3: USB revision 1.0 uhub4 at usb4 "Intel UHCI root hub" rev 1.00/1.00 addr 1 isa0 at pcib0 isadma0 at isa0 pckbc0 at isa0 port 0x60/5 pckbd0 at pckbc0 (kbd slot) pckbc0: using irq 1 for kbd slot wskbd0 at pckbd0: console keyboard, using wsdisplay0 pms0 at pckbc0 (aux slot) pckbc0: using irq 12 for aux slot wsmouse0 at pms0 mux 0 pms0: Synaptics touchpad, firmware 6.2 pcppi0 at isa0 port 0x61 spkr0 at pcppi0 mtrr: Pentium Pro MTRR support vscsi0 at root scsibus1 at vscsi0: 256 targets softraid0 at root scsibus2 at softraid0: 256 targets root on wd0a (10e8ca558223b2b3.a) swap on wd0b dump on wd0b umsm0 at uhub3 port 1 configuration 1 interface 0 "Option N.V. Globetrotter HSDPA Modem" rev 1.10/0.00 addr 2 umsm0 detached umsm0 at uhub3 port 1 configuration 1 interface 0 "Option N.V. Globetrotter HSDPA Modem" rev 1.10/0.00 addr 2 ucom0 at umsm0 umsm1 at uhub3 port 1 configuration 1 interface 1 "Option N.V. Globetrotter HSDPA Modem" rev 1.10/0.00 addr 2 ucom1 at umsm1 Controller /dev/usb0: addr 1: high speed, self powered, config 1, EHCI root hub(0x0000), Intel(0x8086), rev 1.00 port 1 powered port 2 powered port 3 powered port 4 powered port 5 powered port 6 powered port 7 powered port 8 powered Controller /dev/usb1: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x8086), rev 1.00 port 1 powered port 2 powered Controller /dev/usb2: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x8086), rev 1.00 port 1 powered port 2 powered Controller /dev/usb3: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x8086), rev 1.00 port 1 addr 2: full speed, power 500 mA, config 1, Globetrotter HSDPA Modem(0x6971), Option N.V.(0x0af0), rev 0.00, iSerialNumber Serial Number port 2 powered Controller /dev/usb4: addr 1: full speed, self powered, config 1, UHCI root hub(0x0000), Intel(0x8086), rev 1.00 port 1 powered port 2 powered
