Jan Stary <[email protected]> wrote: >This is current/i386 on IBM Thinkpad T40. >I am using a crypto RAID to host my /home partition, >set up in rc.local as follows: > > RAID=/dev/wd0o > HOMEFS=/dev/sd0a > echo mounting encrypted /home > bioctl -h -v -c C -l $RAID softraid0 >fsck $HOMEFS && mount -v -o rw,softdep,noatime,nodev,nosuid $HOMEFS >/home > >This has worked fine for some weeks. Now after the upgrade >to current, it says > > softraid0: sd0 was not shutdown properly > >The filesystem that lives on sd0a thus created >is clean and does not need fscking and mounts fine. > >sd0 at scsibus2 targ 1 lun 0: <OPENBSD, SR CRYPTO, 005> SCSI2 0/direct >fixed >sd0: 20354MB, 512 bytes/sector, 41685328 sectors > >So everything works except I get this message when setting >up the partition at boot time. Has something changed in >the way softraid volumes are handled? In particular, is there >something that needs to be done now to have the softraid >'shut down properly'? I shutdown with 'shutdown -h -p now' >as always, but that gets me this message on the next boot. > > Jan > > >OpenBSD 5.2-current (GENERIC) #36: Sun Oct 14 13:13:06 MDT 2012 > [email protected]:/usr/src/sys/arch/i386/compile/GENERIC >cpu0: Intel(R) Pentium(R) M processor 1500MHz ("GenuineIntel" >686-class) 1.50 GHz >cpu0: >FPU,V86,DE,PSE,TSC,MSR,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,CFLUSH,DS,ACPI,MMX,FXSR ,SSE,SSE2,TM,PBE,EST,TM2 >real mem = 267317248 (254MB) >avail mem = 251985920 (240MB) >mainbus0 at root >bios0 at mainbus0: AT/286+ BIOS, date 06/18/07, BIOS32 rev. 0 @ >0xfd750, SMBIOS rev. 2.33 @ 0xe0010 (61 entries) >bios0: vendor IBM version "1RETDRWW (3.23 )" date 06/18/2007 >bios0: IBM 237382G >apm0 at bios0: Power Management spec V1.2 >acpi at bios0 function 0x0 not configured >pcibios0 at bios0: rev 2.1 @ 0xfd6e0/0x920 >pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdea0/272 (15 entries) >pcibios0: PCI Interrupt Router at 000:31:0 ("Intel 82371FB ISA" rev >0x00) >pcibios0: PCI bus #6 is the last bus >bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1000 0xd1000/0x1000 >0xdc000/0x4000! 0xe0000/0x10000 >cpu0 at mainbus0: (uniprocessor) >cpu0: Enhanced SpeedStep 1496 MHz: speeds: 1500, 1400, 1200, 1000, 800, >600 MHz >pci0 at mainbus0 bus 0: configuration mode 1 (bios) >0:31:1: io address conflict 0x5800/0x8 >0:31:1: io address conflict 0x5808/0x4 >0:31:1: io address conflict 0x5810/0x8 >0:31:1: io address conflict 0x580c/0x4 >pchb0 at pci0 dev 0 function 0 "Intel 82855PM Host" rev 0x03 >intelagp0 at pchb0 >agp0 at intelagp0: aperture at 0xd0000000, size 0x10000000 >ppb0 at pci0 dev 1 function 0 "Intel 82855PM AGP" rev 0x03 >pci1 at ppb0 bus 1 >vga1 at pci1 dev 0 function 0 "ATI Radeon Mobility M7" rev 0x00 >wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation) >wsdisplay0: screen 1-5 added (80x25, vt100 emulation) >radeondrm0 at vga1: irq 11 >drm0 at radeondrm0 >uhci0 at pci0 dev 29 function 0 "Intel 82801DB USB" rev 0x01: irq 11 >uhci1 at pci0 dev 29 function 1 "Intel 82801DB USB" rev 0x01: irq 11 >uhci2 at pci0 dev 29 function 2 "Intel 82801DB USB" rev 0x01: irq 11 >ehci0 at pci0 dev 29 function 7 "Intel 82801DB USB" rev 0x01: irq 11 >usb0 at ehci0: USB revision 2.0 >uhub0 at usb0 "Intel EHCI root hub" rev 2.00/1.00 addr 1 >ppb1 at pci0 dev 30 function 0 "Intel 82801BAM Hub-to-PCI" rev 0x81 >pci2 at ppb1 bus 2 >2:0:0: mem address conflict 0xb0000000/0x1000 >2:0:1: mem address conflict 0xb1000000/0x1000 >cbb0 at pci2 dev 0 function 0 "TI PCI1520 CardBus" rev 0x01: irq 11 >cbb1 at pci2 dev 0 function 1 "TI PCI1520 CardBus" rev 0x01: irq 11 >em0 at pci2 dev 1 function 0 "Intel PRO/1000MT (82540EP)" rev 0x03: irq >11, address 00:0d:60:7f:83:fa >ipw0 at pci2 dev 2 function 0 "Intel PRO/Wireless 2100" rev 0x04: irq >11, address 00:0c:f1:16:9b:b8 >cardslot0 at cbb0 slot 0 flags 0 >cardbus0 at cardslot0: bus 3 device 0 cacheline 0x8, lattimer 0xb0 >pcmcia0 at cardslot0 >cardslot1 at cbb1 slot 1 flags 0 >cardbus1 at cardslot1: bus 6 device 0 cacheline 0x8, lattimer 0xb0 >pcmcia1 at cardslot1 >ichpcib0 at pci0 dev 31 function 0 "Intel 82801DBM LPC" rev 0x01: >24-bit timer at 3579545Hz >pciide0 at pci0 dev 31 function 1 "Intel 82801DBM IDE" rev 0x01: DMA, >channel 0 configured to compatibility, channel 1 configured to >compatibility >wd0 at pciide0 channel 0 drive 0: <HTS548040M9AT00> >wd0: 16-sector PIO, LBA, 35087MB, 71859186 sectors >wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5 >atapiscsi0 at pciide0 channel 1 drive 0 >scsibus0 at atapiscsi0: 2 targets >cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, DVD-ROM GDR8083N, 0K03> ATAPI >5/cdrom removable >cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2 >ichiic0 at pci0 dev 31 function 3 "Intel 82801DB SMBus" rev 0x01: irq >11 >iic0 at ichiic0 >spdmem0 at iic0 addr 0x50: 256MB DDR SDRAM non-parity PC2700CL2.5 >auich0 at pci0 dev 31 function 5 "Intel 82801DB AC97" rev 0x01: irq 11, >ICH4 AC97 >ac97: codec id 0x41445374 (Analog Devices AD1981B) >ac97: codec features headphone, 20 bit DAC, No 3D Stereo >audio0 at auich0 >"Intel 82801DB Modem" rev 0x01 at pci0 dev 31 function 6 not configured >usb1 at uhci0: USB revision 1.0 >uhub1 at usb1 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >usb2 at uhci1: USB revision 1.0 >uhub2 at usb2 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >usb3 at uhci2: USB revision 1.0 >uhub3 at usb3 "Intel UHCI root hub" rev 1.00/1.00 addr 1 >isa0 at ichpcib0 >isadma0 at isa0 >com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo >com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo >pckbc0 at isa0 port 0x60/5 >pckbd0 at pckbc0 (kbd slot) >pckbc0: using irq 1 for kbd slot >wskbd0 at pckbd0: console keyboard, using wsdisplay0 >pms0 at pckbc0 (aux slot) >pckbc0: using irq 12 for aux slot >wsmouse0 at pms0 mux 0 >wsmouse1 at pms0 mux 0 >pms0: Synaptics touchpad, firmware 5.9 >pcppi0 at isa0 port 0x61 >spkr0 at pcppi0 >lpt2 at isa0 port 0x3bc/4: polled >npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16 >fdc0 at isa0 port 0x3f0/6 irq 6 drq 2 >mtrr: Pentium Pro MTRR support >vscsi0 at root >scsibus1 at vscsi0: 256 targets >softraid0 at root >scsibus2 at softraid0: 256 targets >root on wd0a (3a9f38780353c4cf.a) swap on wd0b dump on wd0b >softraid0: sd0 was not shutdown properly >softraid0: sd0 was not shutdown properly >sd0 at scsibus2 targ 1 lun 0: <OPENBSD, SR CRYPTO, 005> SCSI2 0/direct >fixed >sd0: 20354MB, 512 bytes/sector, 41685328 sectors
I've seen the same thing. Adding umount and bioctl -d to rc.shutdown eliminates the warning messages. :) -- Sent from my phone. Please excuse any idiotic automated word choices. It wasn't me. Honest.
