Hi!
I am having hard time getting "NetMos Nm9835" addon PCI adapter going
for gaining two more com ports. OpenBSD 5.2-current of Nov 13 says on
commodity i386 hardware
# dmesg
...
puc0 at pci0 dev 8 function 0 "NetMos Nm9835" rev 0x01: ports: 2 com, 1 lpt
com3 at puc0 port 0 irq 10: ns16550a, 16 byte fifo
com4 at puc0 port 1 irq 10: ns16550a, 16 byte fifo
lpt3 at puc0 port 2 irq 10
and /etc/ttys has
# cat /etc/ttys
...
tty03 "/usr/libexec/getty std.9600" vt200 off secure
tty04 "/usr/libexec/getty std.9600" vt200 off secure
Issuing usual cu gives
# cu -l /dev/cua03 -s 9600
Connected
<and stays here>
# cu -l /dev/cua03 -s 9600
Connected
<and stays here>
I would be thankful if somebody comments whether i am doing wrong
something obious or this particular device isnt supposed to work on
OpenBSD although man puc kind of says it should. (Actually haven't tried
this particular piece on anything else yet). Or some advice how to debug
it to get some meaningful information to make it possible to help me
further. (And i also tried to serve serial console from this computer on
cua03 and cua04, no luck).
Best regards,
Imre
PS This computer has two onboard com ports and they work both ways, i.e.
as serial consoles and as means to get connected to serial consoles
elsewhere. So cable should be good (so to say factory null modem cable).
OpenBSD 5.2-current (GENERIC) #82: Tue Nov 13 13:09:22 MST 2012
dera...@i386.openbsd.org:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Duron(tm) Processor ("AuthenticAMD" 686-class, 64KB L2 cache)
698 MHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,MMXX,3DNOW2,3DNOW
real mem = 2146955264 (2047MB)
avail mem = 2100928512 (2003MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 10/06/00, BIOS32 rev. 0 @ 0xfb350,
SMBIOS rev. 2.3 @ 0xf0800 (38 entries)
bios0: vendor Award Software International, Inc. version "6.00 PG" date
10/06/2000
bios0: VIA Technologies, Inc. VT8363
apm0 at bios0: Power Management spec V1.2 (slowidle)
acpi at bios0 function 0x0 not configured
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xb7d0
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdd00/176 (9 entries)
pcibios0: PCI Exclusive IRQs: 5 10
pcibios0: PCI Interrupt Router at 000:07:0 ("VIA VT82C596A ISA" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x10000 0xd0000/0x1000 0xd1000/0x1800
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "VIA VT8363 Host" rev 0x03
viaagp0 at pchb0: v2
agp0 at viaagp0: aperture at 0xd0000000, size 0x10000000
ppb0 at pci0 dev 1 function 0 "VIA VT8363 AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "NVIDIA Vanta" rev 0x15
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 7 function 0 "VIA VT82C686 ISA" rev 0x22
pciide0 at pci0 dev 7 function 1 "VIA VT82C571 IDE" rev 0x10: ATA66,
channel 0 configured to compatibility, channel 1 configured to compatibility
wd0 at pciide0 channel 0 drive 0: <WDC WD2000JB-32EVA0>
wd0: 16-sector PIO, LBA48, 190781MB, 390719855 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 4
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <HL-DT-ST, CD-RW GCE-8520B, 1.03> ATAPI
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
uhci0 at pci0 dev 7 function 2 "VIA VT83C572 USB" rev 0x10: irq 5
uhci1 at pci0 dev 7 function 3 "VIA VT83C572 USB" rev 0x10: irq 5
viapm0 at pci0 dev 7 function 4 "VIA VT82C686 SMBus" rev 0x30: SMI
iic0 at viapm0
spdmem0 at iic0 addr 0x50: 1GB SDRAM registered ECC PC133CL2
spdmem1 at iic0 addr 0x51: 1GB SDRAM registered ECC PC133CL2
viapm0: 24-bit timer at 3579545Hz
auvia0 at pci0 dev 7 function 5 "VIA VT82C686 AC97" rev 0x20: irq 10
ac97: codec id 0x83847609 (SigmaTel STAC9721/23)
ac97: codec features 18 bit DAC, 18 bit ADC, SigmaTel 3D
audio0 at auvia0
puc0 at pci0 dev 8 function 0 "NetMos Nm9835" rev 0x01: ports: 2 com, 1 lpt
com3 at puc0 port 0 irq 10: ns16550a, 16 byte fifo
com4 at puc0 port 1 irq 10: ns16550a, 16 byte fifo
lpt3 at puc0 port 2 irq 10
em0 at pci0 dev 9 function 0 "Intel PRO/1000GT (82541GI)" rev 0x05: irq
10, address 00:0e:0c:b0:96:b6
em1 at pci0 dev 10 function 0 "Intel PRO/1000MT (82545GM)" rev 0x04: irq
10, address 00:04:23:bd:17:d9
fxp0 at pci0 dev 11 function 0 "Intel 8255x" rev 0x0c, i82550: irq 5,
address 00:03:47:9b:76:56
inphy0 at fxp0 phy 1: i82555 10/100 PHY, rev. 4
re0 at pci0 dev 12 function 0 "Realtek 8169" rev 0x10: RTL8169/8110SB
(0x1000), irq 10, address 00:06:4f:63:e3:d7
rgephy0 at re0 phy 7: RTL8169S/8110S PHY, rev. 3
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
com1: console
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
usb0 at uhci0: USB revision 1.0
uhub0 at usb0 "VIA UHCI root hub" rev 1.00/1.00 addr 1
usb1 at uhci1: USB revision 1.0
uhub1 at usb1 "VIA UHCI root hub" rev 1.00/1.00 addr 1
mtrr: Pentium Pro MTRR support
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
root on wd0e (24635f1cb2e8a1bb.e) swap on wd0b dump on wd0b
