Hi all,
I'm having trouble getting my Cisco Aironet PCM352 card working on my
compaq presario 2100 (AMD). In particular, I get the message:
an0: failed to enable MAC
during boot of the install, and when I try to use dhcp. I received
this message with 3.8-release. I decided not to configure the network
with an0 during the install, and do it afterwards since there was
clearly something wrong. Following the install, the system booted
without that message. ancontrol -S returns:
MAC address: [ 00:0b:5f:0e:64:2c ]
Operating mode: [ configured MAC ON RX ON synced associated ]
Error code: [ 00 ]
Signal strength: [ 100% ]
Signal quality: [ 2f ]
Current SSID: [ snikeris ]
Current AP name: [ ]
Current BSSID: [ 00:0c:41:4e:46:36 ]
Beacon period: [ 100 ]
DTIM period: [ 1 ]
ATIM duration: [ 0 ]
HOP period: [ 200 ]
Channel set: [ 0 ]
Current channel: [ 6 ]
Hops to backbone: [ 0 ]
Total AP load: [ 0 ]
Our generated load: [ 0 ]
Accumulated ARL: [ 0 ]
Ok cool, it looks like it associated with my AP (snikeris). Some
possibly related weirdness:
# ancontrol -N
SSID 1: [ ]
SSID 2: [ ]
SSID 3: [ ]
# ancontrol -n snikeris
# ancontrol -N
SSID 1: [ ]
SSID 2: [ ]
SSID 3: [ ]
If I understand ancontrol(8) correctly this should read:
# ancontrol -N
SSID 1: [ snikeris ]
SSID 2: [ ]
SSID 3: [ ]
Then I created /etc/hostname.an0 that just contained "dhcp" as
instructed in dhcp(8) and rebooted. I can successfully connect to my
linksys router with dhcp with ethernet, so I assume I should be able
to with this wireless card (I can connect with wireless and dhcp in
windows xp) Then I after the normal stuff I get:
starting network
an0: failed to enable MAC
DHCPDISCOVER on an0 to 255.255.255.255 port 67 interval 2
send_packet: Network is down
.
.
.
No DHCPOFFERS received
Then an ancontrol -n snikeris returns:
an0: failed to enable MAC
So it seems like dhcp somehow messed up the card.
Searching the archives turned up similar problems, but no solutions.
I suspected it might be an issue with the firmware, so I upgraded it
to the latest firmware (5.60.21), but the problem persists. It is
interesting to note that ancontrol -I returns:
OUI: [ 00:40:96 ]
Product number: [ 10 ]
Manufacturer name: [ Cisco Systems ]
Produce name: [ 350 Series ]
Firmware version: [ 5 ]
OEM MAC address: [ 00:0b:5f:0e:64:2c ]
Aironet MAC address: [ 00:0b:5f:0e:64:2c ]
Radio type: [ 802.11 DS ]
Regulatory domain: [ 0 ]
Assigned CallID: [ 00:00:00:00:00:00 ]
Supported speeds: [ 1.0Mbps 2.0Mbps 5.5Mbps 11.0Mbps ]
RX Diversity: [ antenna 1 and 2 ]
TX Diversity: [ antenna 1 and 2 ]
Supported power levels: [ 1 5 20 30 50 100 0 0 ]
Hardware revision: [ 00:30 ]
Software revision: [ 05:60 ]
Software subrevision: [ 00:15 ]
Interface revision: [ 00:00 ]
Bootblock revision: [ 01:50 ]
Of particular interest are the last few lines. It says the Software
revision is 05:60 and the software subrevision is 00:15. I would
assume this would correspond with firmware version 5.60.15. This is
not the firmware that I installed (5.60.21). I'm pretty sure that the
firmware installed correctly since the ACU utility in windows reports
that the firmware is indeed 5.60.21
Anyone have any ideas what the issue could be? If anyone has this
card working on 3.8, could you please let me know what firmware
version you are using? If an older firmware is what is needed, thats
fine.
Thanks in advance for any suggestions,
Joe Snikeris
dmesg without the /etc/hostname.an0 file:
-------------------------------------------------------------
OpenBSD 3.8 (GENERIC) #138: Sat Sep 10 15:41:37 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: mobile AMD Athlon(tm) XP2200+ ("AuthenticAMD" 686-class, 256KB
L2 cache) 1.79 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
cpu0: AMD Powernow: FID VID TTP
real mem = 736665600 (719400K)
avail mem = 664600576 (649024K)
using 4278 buffers containing 36937728 bytes (36072K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(5c) BIOS, date 03/17/04, BIOS32 rev. 0 @ 0xfd730
pcibios0 at bios0: rev 2.1 @ 0xfd730/0x8d0
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf10/208 (11 entries)
pcibios0: PCI Interrupt Router at 000:07:0 ("Acer Labs M1533 ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xf000 0xcf000/0x800 0xdb000/0x1000! 0xdc000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ATI RS100 AGP" rev 0x13
ppb0 at pci0 dev 1 function 0 "ATI RS100 PCI" rev 0x01
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon IGP 320M" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ohci0 at pci0 dev 2 function 0 "Acer Labs M5237 USB" rev 0x03: irq 9,
version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Acer Labs OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
autri0 at pci0 dev 6 function 0 "Acer Labs M5451 Audio" rev 0x02: irq 5
ac97: codec id 0x43585429 (Conexant CX20468 rev 1)
ac97: codec features reserved, headphone, 18 bit DAC, 18 bit ADC, No 3D Stereo
audio0 at autri0
midi0 at autri0: <4DWAVE MIDI UART>
pcib0 at pci0 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
"Acer Labs M5457 Modem" rev 0x00 at pci0 dev 8 function 0 not configured
"Broadcom BCM4306" rev 0x02 at pci0 dev 9 function 0 not configured
cbb0 at pci0 dev 10 function 0 "O2 Micro OZ69[17]2 CardBus" rev 0x00: irq 10
"Texas Instruments TSB43AB21 FireWire" rev 0x00 at pci0 dev 12
function 0 not configured
pciide0 at pci0 dev 16 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
DMA, channel 0 wired to compatibility, channel 1 wired to
compatibility
wd0 at pciide0 channel 0 drive 0: <IC25N020ATCS04-0>
wd0: 16-sector PIO, LBA, 19077MB, 39070080 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SONY, DVD+RW DW-P50A, 1.8e> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
"Acer Labs M7101 Power" rev 0x00 at pci0 dev 17 function 0 not configured
sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00: DP83816A,
irq 11, address 00:0d:9d:81:85:a1
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
biomask e74d netmask ef4d ttymask ffcf
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
an0 at pcmcia0 function 0 "Cisco Systems, 350 Series Wireless LAN
Adapter": address 00:0b:5f:0e:64:2c
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
-------------------------------------------------------------
dmesg with the /etc/hostname.an0 file
-------------------------------------------------------------
OpenBSD 3.8 (GENERIC) #138: Sat Sep 10 15:41:37 MDT 2005
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: mobile AMD Athlon(tm) XP2200+ ("AuthenticAMD" 686-class, 256KB
L2 cache) 1.79 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
cpu0: AMD Powernow: FID VID TTP
real mem = 736665600 (719400K)
avail mem = 664600576 (649024K)
using 4278 buffers containing 36937728 bytes (36072K) of memory
mainbus0 (root)
bios0 at mainbus0: AT/286+(5c) BIOS, date 03/17/04, BIOS32 rev. 0 @ 0xfd730
pcibios0 at bios0: rev 2.1 @ 0xfd730/0x8d0
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfdf10/208 (11 entries)
pcibios0: PCI Interrupt Router at 000:07:0 ("Acer Labs M1533 ISA" rev 0x00)
pcibios0: PCI bus #2 is the last bus
bios0: ROM list: 0xc0000/0xf000 0xcf000/0x800 0xdb000/0x1000! 0xdc000/0x4000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "ATI RS100 AGP" rev 0x13
ppb0 at pci0 dev 1 function 0 "ATI RS100 PCI" rev 0x01
pci1 at ppb0 bus 1
vga1 at pci1 dev 5 function 0 "ATI Radeon IGP 320M" rev 0x00
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
ohci0 at pci0 dev 2 function 0 "Acer Labs M5237 USB" rev 0x03: irq 9,
version 1.0, legacy support
usb0 at ohci0: USB revision 1.0
uhub0 at usb0
uhub0: Acer Labs OHCI root hub, rev 1.00/1.00, addr 1
uhub0: 4 ports with 4 removable, self powered
autri0 at pci0 dev 6 function 0 "Acer Labs M5451 Audio" rev 0x02: irq 5
ac97: codec id 0x43585429 (Conexant CX20468 rev 1)
ac97: codec features reserved, headphone, 18 bit DAC, 18 bit ADC, No 3D Stereo
audio0 at autri0
midi0 at autri0: <4DWAVE MIDI UART>
pcib0 at pci0 dev 7 function 0 "Acer Labs M1533 ISA" rev 0x00
"Acer Labs M5457 Modem" rev 0x00 at pci0 dev 8 function 0 not configured
"Broadcom BCM4306" rev 0x02 at pci0 dev 9 function 0 not configured
cbb0 at pci0 dev 10 function 0 "O2 Micro OZ69[17]2 CardBus" rev 0x00: irq 10
"Texas Instruments TSB43AB21 FireWire" rev 0x00 at pci0 dev 12
function 0 not configured
pciide0 at pci0 dev 16 function 0 "Acer Labs M5229 UDMA IDE" rev 0xc4:
DMA, channel 0 wired to compatibility, channel 1 wired to
compatibility
wd0 at pciide0 channel 0 drive 0: <IC25N020ATCS04-0>
wd0: 16-sector PIO, LBA, 19077MB, 39070080 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SONY, DVD+RW DW-P50A, 1.8e> SCSI0
5/cdrom removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
"Acer Labs M7101 Power" rev 0x00 at pci0 dev 17 function 0 not configured
sis0 at pci0 dev 18 function 0 "NS DP83815 10/100" rev 0x00: DP83816A,
irq 11, address 00:0d:9d:81:85:a1
nsphyter0 at sis0 phy 0: DP83815 10/100 PHY, rev. 1
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pmsi0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pmsi0 mux 0
pcppi0 at isa0 port 0x61
midi1 at pcppi0: <PC speaker>
spkr0 at pcppi0
sysbeep0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
npx0 at isa0 port 0xf0/16: using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
cardslot0 at cbb0 slot 0 flags 0
cardbus0 at cardslot0: bus 2 device 0 cacheline 0x0, lattimer 0x20
pcmcia0 at cardslot0
biomask e74d netmask ef4d ttymask ffcf
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
an0 at pcmcia0 function 0 "Cisco Systems, 350 Series Wireless LAN
Adapter": address 00:0b:5f:0e:64:2c
dkcsum: wd0 matches BIOS drive 0x80
root on wd0a
rootdev=0x0 rrootdev=0x300 rawdev=0x302
an0: failed to enable MAC
an0: failed to enable MAC
-------------------------------------------------------------
