Updated dmesg(s)...
amd64:
OpenBSD 5.4-current (RAMDISK_CD) #167: Fri Dec 27 22:40:53 MST 2013
[email protected]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
RTC BIOS diagnostic error
ff<clock_battery,ROM_cksum,config_unit,memory_size,fixed_disk,invalid_time>
real mem = 2098634752 (2001MB)
avail mem = 2037903360 (1943MB)
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.7 @ 0x7e17c420 (6 entries)
bios0: vendor coreboot version
"EDK_2.08.00_20130410_221-1434-g871c820-dirty" date 08/20/2013
bios0: PC Engines APU
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S2 S3 S4 S5
acpi0: tables DSDT FACP HPET APIC HEST SSDT SSDT SSDT
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (AGPB)
acpiprt2 at acpi0: bus -1 (PBR2)
acpiprt3 at acpi0: bus 1 (PBR4)
acpiprt4 at acpi0: bus 2 (PBR5)
acpiprt5 at acpi0: bus 3 (PBR6)
acpiprt6 at acpi0: bus 4 (PBR7)
acpiprt7 at acpi0: bus -1 (PBR9)
acpiprt8 at acpi0: bus -1 (PBRA)
acpiprt9 at acpi0: bus 6 (PE20)
acpiprt10 at acpi0: bus -1 (PE21)
acpiprt11 at acpi0: bus -1 (PE22)
acpiprt12 at acpi0: bus -1 (PE23)
acpiprt13 at acpi0: bus 5 (PIBR)
mpbios at bios0 not configured
cpu0 at mainbus0: (uniprocessor)
cpu0: AMD G-T40N Processor, 1000.15 MHz
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,MWAIT,SSSE3,CX16,POPCNT,NXE,MMXX,FFXSR,LONG,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,ABM,SSE4A,MASSE,3DNOWP,IBS,SKINIT,ITSC
cpu0: 32KB 64b/line 2-way I-cache, 32KB 64b/line 8-way D-cache, 512KB
64b/line 16-way L2 cache
cpu0: 8 4MB entries fully associative
cpu0: DTLB 40 4KB entries fully associative, 8 4MB entries fully
associative
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "AMD AMD64 14h Host" rev 0x00
ppb0 at pci0 dev 4 function 0 "AMD AMD64 14h PCIE" rev 0x00pci_intr_map:
bad interrupt line 16
pci1 at ppb0 bus 1
re0 at pci1 dev 0 function 0 "Realtek 8168" rev 0x06pci_intr_map: bad
interrupt line 16
: couldn't map interrupt
ppb1 at pci0 dev 5 function 0 "AMD AMD64 14h PCIE" rev 0x00pci_intr_map:
bad interrupt line 17
pci2 at ppb1 bus 2
re1 at pci2 dev 0 function 0 "Realtek 8168" rev 0x06pci_intr_map: bad
interrupt line 17
: couldn't map interrupt
ppb2 at pci0 dev 6 function 0 "AMD AMD64 14h PCIE" rev 0x00pci_intr_map:
bad interrupt line 18
pci3 at ppb2 bus 3
re2 at pci3 dev 0 function 0 "Realtek 8168" rev 0x06pci_intr_map: bad
interrupt line 18
: couldn't map interrupt
ppb3 at pci0 dev 7 function 0 "AMD AMD64 14h PCIE" rev 0x00pci_intr_map:
bad interrupt line 19
pci4 at ppb3 bus 4
athn0 at pci4 dev 0 function 0 "Atheros AR9281" rev 0x01: can't map
interrupt
ahci0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x40pci_intr_map:
bad interrupt line 19
: unable to map interrupt
ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00pci_intr_map:
bad interrupt line 18
: couldn't map interrupt
ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00pci_intr_map:
bad interrupt line 17
: couldn't map interrupt
ohci1 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00pci_intr_map:
bad interrupt line 18
: couldn't map interrupt
ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00pci_intr_map:
bad interrupt line 17
: couldn't map interrupt
"ATI SBx00 SMBus" rev 0x42 at pci0 dev 20 function 0 not configured
pciide0 at pci0 dev 20 function 1 "ATI SB700 IDE" rev 0x40: DMA, channel
0 configured to compatibility, channel 1 configured to compatibility
"ATI SB700 ISA" rev 0x40 at pci0 dev 20 function 3 not configured
ppb4 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x40
pci5 at ppb4 bus 5
ohci2 at pci0 dev 20 function 5 "ATI SB700 USB" rev 0x00pci_intr_map:
bad interrupt line 18
: couldn't map interrupt
ppb5 at pci0 dev 21 function 0 "ATI SB800 PCIE" rev 0x00
pci6 at ppb5 bus 6
ohci3 at pci0 dev 22 function 0 "ATI SB700 USB" rev 0x00pci_intr_map:
bad interrupt line 18
: couldn't map interrupt
ehci2 at pci0 dev 22 function 2 "ATI SB700 USB2" rev 0x00pci_intr_map:
bad interrupt line 17
: couldn't map interrupt
pchb1 at pci0 dev 24 function 0 "AMD AMD64 14h Link Cfg" rev 0x43
pchb2 at pci0 dev 24 function 1 "AMD AMD64 14h Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 14h DRAM Cfg" rev 0x00
pchb4 at pci0 dev 24 function 3 "AMD AMD64 14h Misc Cfg" rev 0x00
pchb5 at pci0 dev 24 function 4 "AMD AMD64 14h CPU Power" rev 0x00
pchb6 at pci0 dev 24 function 5 "AMD AMD64 14h Reserved" rev 0x00
pchb7 at pci0 dev 24 function 6 "AMD AMD64 14h NB Power" rev 0x00
pchb8 at pci0 dev 24 function 7 "AMD AMD64 14h Reserved" rev 0x00
isa0 at mainbus0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
softraid0 at root
scsibus0 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
i386:
OpenBSD 5.4-current (RAMDISK_CD) #154: Fri Dec 27 10:46:12 MST 2013
[email protected]:/usr/src/sys/arch/i386/compile/RAMDISK_CD
RTC BIOS diagnostic error
ff<clock_battery,ROM_cksum,config_unit,memory_size,fixed_disk,invalid_time>
cpu0: AMD G-T40N Processor ("AuthenticAMD" 686-class, 512KB L2 cache)
1.01 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,NXE,MMXX,FFXSR,LONG,SSE3,MWAIT,SSSE3,CX16,POPCNT,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,ABM,SSE4A,MASSE,3DNOWP,IBS,SKINIT,WDT,ITSC
real mem = 2114949120 (2016MB)
avail mem = 2073145344 (1977MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 06/23/99, BIOS32 rev. 0 @ 0xff046,
SMBIOS rev. 2.7 @ 0x7e17c420 (6 entries)
bios0: vendor coreboot version
"EDK_2.08.00_20130410_221-1434-g871c820-dirty" date 08/20/2013
bios0: PC Engines APU
acpi0 at bios0: rev 0
acpi0: sleep states S0 S1 S2 S3 S4 S5
acpi0: tables DSDT FACP HPET APIC HEST SSDT SSDT SSDT
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt1 at acpi0: bus -1 (AGPB)
acpiprt2 at acpi0: bus -1 (PBR2)
acpiprt3 at acpi0: bus 1 (PBR4)
acpiprt4 at acpi0: bus 2 (PBR5)
acpiprt5 at acpi0: bus 3 (PBR6)
acpiprt6 at acpi0: bus 4 (PBR7)
acpiprt7 at acpi0: bus -1 (PBR9)
acpiprt8 at acpi0: bus -1 (PBRA)
acpiprt9 at acpi0: bus 6 (PE20)
acpiprt10 at acpi0: bus -1 (PE21)
acpiprt11 at acpi0: bus -1 (PE22)
acpiprt12 at acpi0: bus -1 (PE23)
acpiprt13 at acpi0: bus 5 (PIBR)
mpbios at bios0 function 0x0 not configured
bios0: ROM list: 0xc0000/0xa00 0xee000/0x2000!
cpu0 at mainbus0: (uniprocessor)
pci0 at mainbus0 bus 0: configuration mode 1 (bios)
pchb0 at pci0 dev 0 function 0 "AMD AMD64 14h Host" rev 0x00
ppb0 at pci0 dev 4 function 0 "AMD AMD64 14h PCIE" rev 0x00pci_intr_map:
bad interrupt line 16
pci1 at ppb0 bus 1
re0 at pci1 dev 0 function 0 "Realtek 8168" rev 0x06pci_intr_map: bad
interrupt line 16
: couldn't map interrupt
ppb1 at pci0 dev 5 function 0 "AMD AMD64 14h PCIE" rev 0x00pci_intr_map:
bad interrupt line 17
pci2 at ppb1 bus 2
re1 at pci2 dev 0 function 0 "Realtek 8168" rev 0x06pci_intr_map: bad
interrupt line 17
: couldn't map interrupt
ppb2 at pci0 dev 6 function 0 "AMD AMD64 14h PCIE" rev 0x00pci_intr_map:
bad interrupt line 18
pci3 at ppb2 bus 3
re2 at pci3 dev 0 function 0 "Realtek 8168" rev 0x06pci_intr_map: bad
interrupt line 18
: couldn't map interrupt
ppb3 at pci0 dev 7 function 0 "AMD AMD64 14h PCIE" rev 0x00pci_intr_map:
bad interrupt line 19
pci4 at ppb3 bus 4
athn0 at pci4 dev 0 function 0 "Atheros AR9281" rev 0x01: can't map
interrupt
ahci0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x40pci_intr_map:
bad interrupt line 19
: unable to map interrupt
ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00pci_intr_map:
bad interrupt line 18
: couldn't map interrupt
ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00pci_intr_map:
bad interrupt line 17
: couldn't map interrupt
ohci1 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00pci_intr_map:
bad interrupt line 18
: couldn't map interrupt
ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00pci_intr_map:
bad interrupt line 17
: couldn't map interrupt
"ATI SBx00 SMBus" rev 0x42 at pci0 dev 20 function 0 not configured
pciide0 at pci0 dev 20 function 1 "ATI SB700 IDE" rev 0x40: DMA, channel
0 configured to compatibility, channel 1 configured to compatibility
pcib0 at pci0 dev 20 function 3 "ATI SB700 ISA" rev 0x40
ppb4 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x40
pci5 at ppb4 bus 5
ohci2 at pci0 dev 20 function 5 "ATI SB700 USB" rev 0x00pci_intr_map:
bad interrupt line 18
: couldn't map interrupt
ppb5 at pci0 dev 21 function 0 "ATI SB800 PCIE" rev 0x00
pci6 at ppb5 bus 6
ohci3 at pci0 dev 22 function 0 "ATI SB700 USB" rev 0x00pci_intr_map:
bad interrupt line 18
: couldn't map interrupt
ehci2 at pci0 dev 22 function 2 "ATI SB700 USB2" rev 0x00pci_intr_map:
bad interrupt line 17
: couldn't map interrupt
pchb1 at pci0 dev 24 function 0 "AMD AMD64 14h Link Cfg" rev 0x43
pchb2 at pci0 dev 24 function 1 "AMD AMD64 14h Address Map" rev 0x00
pchb3 at pci0 dev 24 function 2 "AMD AMD64 14h DRAM Cfg" rev 0x00
pchb4 at pci0 dev 24 function 3 "AMD AMD64 14h Misc Cfg" rev 0x00
pchb5 at pci0 dev 24 function 4 "AMD AMD64 14h CPU Power" rev 0x00
pchb6 at pci0 dev 24 function 5 "AMD AMD64 14h Reserved" rev 0x00
pchb7 at pci0 dev 24 function 6 "AMD AMD64 14h NB Power" rev 0x00
pchb8 at pci0 dev 24 function 7 "AMD AMD64 14h Reserved" rev 0x00
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com0: console
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
fdc0: drive 0: unknown device type 0xf0
fd0 at fdc0 drive 0: density unknown
fdc0: drive 1: unknown device type 0xf0
fd1 at fdc0 drive 1: density unknown
softraid0 at root
scsibus0 at softraid0: 256 targets
root on rd0a swap on rd0b dump on rd0b
On Mon, Dec 16, 2013, at 13:19, Byron Klippert wrote:
> http://pcengines.ch/apu.htm
>
>
> Introduction: Thank you for taking the time to test our first round
> prototypes of the new apu system board. Since this is a prototype, there
> are a few bugs... Use at your own risk, don't use these boards for
> anything critical.
>
>
> ############ BIOS boot capture:
>
> coreboot-EDK_2.08.00_20130410_221-1434-g871c820-dirty Tue Aug 20
> 15:46:42 MDT 2013 booting...
> PCI: Left over static devices:
> PCI: 00:15.1
> PCI: 00:15.2
> PCI: 00:15.3
> PCI: Check your devicetree.cb.
> APIC: 00 missing read_resources
> APIC: 01 missing read_resources
> Start bios (version ?-20130820_154629-owner-HP)
> CPU Mhz=1001
> Found 30 PCI devices (max PCI bus is 06)
> Found 2 cpu(s) max supported 2 cpu(s)
> Copying PIR from 0x7e16f000 to 0x000fdb40
> Copying MPTABLE from 0x7e170000/7e170010 to 0x000fda00
> Copying ACPI RSDP from 0x7e171000 to 0x000fd9e0
> Copying SMBIOS entry point from 0x7e17c400 to 0x000fd9c0
> Scan for VGA option rom
> EHCI init on dev 00:12.2 (regs=0xfeb08420)
> EHCI init on dev 00:13.2 (regs=0xfeb08520)
> OHCI init on dev 00:14.5 (regs=0xfeb06000)
> EHCI init on dev 00:16.2 (regs=0xfeb08620)
> Found 1 lpt ports
> Found 1 serial ports
> ATA controller 1 at 1f0/3f4/4010 (irq 14 dev a1)
> ATA controller 2 at 170/374/4018 (irq 15 dev a1)
> AHCI controller at 11.0, iobase feb08000, irq 0
> Searching bootorder for: /rom@img/sortbootorder
> Searching bootorder for: /rom@img/memtest
> Searching bootorder for: /pci@i0cf8/*@11/drive@0/disk@0
> AHCI/0: registering: "AHCI/0: SuperSSpeed S238 16GB ATA-7 Hard-Disk
> (15258 MiBytes)"
> Searching bootorder for: /pci@i0cf8/usb@16,2/storage@1/*@0/*@0,0
> Searching bootorder for: /pci@i0cf8/usb@16,2/usb-*@1
> USB MSC vendor='Multiple' product='Card Reader' rev='1.00' type=0
> removable=1
> Searching bootorder for: /pci@i0cf8/usb@12,2/storage@1/*@0/*@0,0
> Searching bootorder for: /pci@i0cf8/usb@12,2/usb-*@1
> USB MSC vendor='Lexar' product='JD FireFly' rev='1100' type=0
> removable=1
> USB MSC blksize=512 sectors=7831552
> USB MSC blksize=512 sectors=7995392
> All threads complete.
> Scan for option roms
> Press F12 for boot menu.
>
> Select boot device:
>
> 1. USB MSC Drive Multiple Card Reader 1.00
> 2. USB MSC Drive Lexar JD FireFly 1100
> 3. AHCI/0: SuperSSpeed S238 16GB ATA-7 Hard-Disk (15258 MiByte
> 4. Payload [sortbootorder]
> 5. Payload [memtest]
>
> drive 0x000fd8d0: PCHS=0/0/0 translation=lba LCHS=971/128/63 s=7831552
> drive 0x000fd900: PCHS=0/0/0 translation=lba LCHS=991/128/63 s=7995392
> drive 0x000fd930: PCHS=16383/16/63 translation=lba LCHS=1024/255/63
> s=31248704
> Space available for UMB: 000c0000-000ee000
> Returned 49152 bytes of ZoneHigh
> e820 map has 6 items:
> 0: 0000000000000000 - 000000000009fc00 = 1 RAM
> 1: 000000000009fc00 - 00000000000a0000 = 2 RESERVED
> 2: 00000000000f0000 - 0000000000100000 = 2 RESERVED
> 3: 0000000000100000 - 000000007e16ac00 = 1 RAM
> 4: 000000007e16ac00 - 000000007efffc00 = 2 RESERVED
> 5: 00000000f8000000 - 00000000f9000000 = 2 RESERVED
> enter handle_19:
> NULL
> Booting from Hard Disk...
> Booting from 0000:7c00
> Using drive 0, partition 3.
> Loading.....
> probing: pc0 com0 apm pci mem[639K 2016M a20=on]
> disk: hd0+ hd1+ hd2*
> >> OpenBSD/i386 BOOT 3.21
> boot> stty com0 115200
> boot> set tty com0
> switching console to com0
>
>
>
> ############ dmesg capture:
>
> switching console to com0
> òzÁ¹ M½i386 BOOT 3.21
> boot> boot bsd.rd.amd64.snapshot
> booting hd0a:bsd.rd.amd64.snapshot: 3118100+960644+2897040+0+528720
> [80+338136+2
> 19474]=0xbb16d0
> entry point at 0x10001e0
> Copyright (c) 1982, 1986, 1989, 1991, 1993
> The Regents of the University of California. All rights
> reserved.
> Copyright (c) 1995-2013 OpenBSD. All rights reserved.
> http://www.OpenBSD.org
>
> OpenBSD 5.4-current (RAMDISK_CD) #147: Mon Dec 9 16:39:35 MST 2013
> [email protected]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD
> RTC BIOS diagnostic error
> ff<clock_battery,ROM_cksum,config_unit,memory_size,fixed_disk,invalid_time>
> real mem = 2098634752 (2001MB)
> avail mem = 2037907456 (1943MB)
> mainbus0 at root
> bios0 at mainbus0: SMBIOS rev. 2.7 @ 0x7e17c420 (6 entries)
> bios0: vendor coreboot version
> "EDK_2.08.00_20130410_221-1434-g871c820-dirty" date 08/20/2013
> bios0: PC Engines APU
> acpi0 at bios0: rev 0, ACPI control unavailable
> mpbios at bios0 not configured
> cpu0 at mainbus0: (uniprocessor)
> cpu0: AMD G-T40N Processor, 1000.13 MHz
> cpu0:
> FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,MMX,FXSR,SSE,SSE2,HTT,SSE3,MWAIT,SSSE3,CX16,POPCNT,NXE,MMXX,FFXSR,LONG,LAHF,CMPLEG,SVM,EAPICSP,AMCR8,ABM,SSE4A,MASSE,3DNOWP,IBS,SKINIT,ITSC
> cpu0: 32KB 64b/line 2-way I-cache, 32KB 64b/line 8-way D-cache, 512KB
> 64b/line 16-way L2 cache
> cpu0: 8 4MB entries fully associative
> cpu0: DTLB 40 4KB entries fully associative, 8 4MB entries fully
> associative
> pci0 at mainbus0 bus 0
> pchb0 at pci0 dev 0 function 0 "AMD AMD64 14h Host" rev 0x00
> ppb0 at pci0 dev 4 function 0 "AMD AMD64 14h PCIE" rev 0x00
> pci1 at ppb0 bus 1
> re0 at pci1 dev 0 function 0 "Realtek 8168" rev 0x06: couldn't map
> interrupt
> ppb1 at pci0 dev 5 function 0 "AMD AMD64 14h PCIE" rev 0x00
> pci2 at ppb1 bus 2
> re1 at pci2 dev 0 function 0 "Realtek 8168" rev 0x06: couldn't map
> interrupt
> ppb2 at pci0 dev 6 function 0 "AMD AMD64 14h PCIE" rev 0x00
> pci3 at ppb2 bus 3
> re2 at pci3 dev 0 function 0 "Realtek 8168" rev 0x06: couldn't map
> interrupt
> ppb3 at pci0 dev 7 function 0 "AMD AMD64 14h PCIE" rev 0x00
> pci4 at ppb3 bus 4
> athn0 at pci4 dev 0 function 0 "Atheros AR9281" rev 0x01: can't map
> interrupt
> ahci0 at pci0 dev 17 function 0 "ATI SBx00 SATA" rev 0x40: unable to map
> interrupt
> ohci0 at pci0 dev 18 function 0 "ATI SB700 USB" rev 0x00: couldn't map
> interrupt
> ehci0 at pci0 dev 18 function 2 "ATI SB700 USB2" rev 0x00: couldn't map
> interrupt
> ohci1 at pci0 dev 19 function 0 "ATI SB700 USB" rev 0x00: couldn't map
> interrupt
> ehci1 at pci0 dev 19 function 2 "ATI SB700 USB2" rev 0x00: couldn't map
> interrupt
> "ATI SBx00 SMBus" rev 0x42 at pci0 dev 20 function 0 not configured
> pciide0 at pci0 dev 20 function 1 "ATI SB700 IDE" rev 0x40: DMA, channel
> 0 configured to compatibility, channel 1 configured to compatibility
> "ATI SB700 ISA" rev 0x40 at pci0 dev 20 function 3 not configured
> ppb4 at pci0 dev 20 function 4 "ATI SB600 PCI" rev 0x40
> pci5 at ppb4 bus 5
> ohci2 at pci0 dev 20 function 5 "ATI SB700 USB" rev 0x00: couldn't map
> interrupt
> ppb5 at pci0 dev 21 function 0 "ATI SB800 PCIE" rev 0x00
> pci6 at ppb5 bus 6
> ohci3 at pci0 dev 22 function 0 "ATI SB700 USB" rev 0x00: couldn't map
> interrupt
> ehci2 at pci0 dev 22 function 2 "ATI SB700 USB2" rev 0x00: couldn't map
> interrupt
> pchb1 at pci0 dev 24 function 0 "AMD AMD64 14h Link Cfg" rev 0x43
> pchb2 at pci0 dev 24 function 1 "AMD AMD64 14h Address Map" rev 0x00
> pchb3 at pci0 dev 24 function 2 "AMD AMD64 14h DRAM Cfg" rev 0x00
> pchb4 at pci0 dev 24 function 3 "AMD AMD64 14h Misc Cfg" rev 0x00
> pchb5 at pci0 dev 24 function 4 "AMD AMD64 14h CPU Power" rev 0x00
> pchb6 at pci0 dev 24 function 5 "AMD AMD64 14h Reserved" rev 0x00
> pchb7 at pci0 dev 24 function 6 "AMD AMD64 14h NB Power" rev 0x00
> pchb8 at pci0 dev 24 function 7 "AMD AMD64 14h Reserved" rev 0x00
> isa0 at mainbus0
> com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
> com0: console
> softraid0 at root
> scsibus0 at softraid0: 256 targets
> root on rd0a swap on rd0b dump on rd0b
> erase ^?, werase ^W, kill ^U, intr ^C, status ^T
>
> Welcome to the OpenBSD/amd64 5.4 installation program.
> (I)nstall, (U)pgrade, (A)utoinstall or (S)hell?
>
>
>
> --
> Byron Klippert
> [email protected]
> c. 867-336-1306
>
--
Byron Klippert
[email protected]
c. 867-336-1306
