Good morning misc/
I purchased a couple of ubequitys edgerouter lite boxes.
And while the ubequity os is "ok" (better than most small home routers
anyhow) I quickly started missing my obsd, this is why I bought them
after all.
I am fine netbooting for the time being. however are there any hints to
skip the prompt for the root device?
you know the one asking for
root device:
I would also welcome any hints on updating a diskless set.
My current method is based roughly on the install script.
detar sets preserving permissions(excepting etc??.tgz)
reboot into arches bsd.rd to rebuild device nodes
reboot and run sysmerge to merge etc??.tgz
full serial boot log:
Looking for valid bootloader image....
Jumping to start of image at address 0xbfc80000
U-Boot 1.1.1 (UBNT Build ID: 4493936-g009d77b) (Build time: Sep 20 2012
- 15:48:51)
BIST check passed.
UBNT_E100 r1:2, r2:14, serial #: DC9FDB803A4D
Core clock: 500 MHz, DDR clock: 266 MHz (532 Mhz data rate)
DRAM: 512 MB
Clearing DRAM....... done
Flash: 4 MB
Net: octeth0, octeth1, octeth2
USB: (port 0) scanning bus for devices... 1 USB Devices found
scanning bus for storage devices...
Device 0: Vendor: Prod.: USB DISK 2.0 Rev: PMAP
Type: Removable Hard Disk
Capacity: 3700.6 MB = 3.6 GB (7579008 x 512)
0
Interface 0 has 3 ports (RGMII)
Using octeth0 device
TFTP from server 192.168.16.5; our IP address is 192.168.16.16
Filename 'bsd.sp.octeon'.
Load address: 0x9f00000
Loading: octeth0: Up 1000 Mbps Full duplex (port 0)
###########################
[76/276]
done
Bytes transferred = 3734226 (38fad2 hex), 9855 Kbytes/sec
ELF file is 64 bit
Allocating memory for ELF segment: addr: 0xffffffff81000000 (adjusted
to: 0x1000000), size 0x3bfc70
Allocated memory for ELF segment: addr: 0xffffffff81000000, size 0x3bfc70
Processing PHDR 0
Loading 334bf8 bytes at ffffffff81000000
Clearing 8b078 bytes at ffffffff81334bf8
## Loading Linux kernel with entry point: 0xffffffff81000000 ...
Bootloader: Done loading app on coremask: 0x1
Total DRAM Size 0x0000000020000000
Bank 0 = 0x00000000013C0000 -> 0x000000000FFFFFFF
mem_layout[0] page 0x00000000000004F0 -> 0x0000000000003FFF
boot_desc->argv[1] = root=/dev/cnmac0
Initial setup done, switching console.
boot_desc->desc_ver:7
boot_desc->desc_size:400
boot_desc->stack_top:0
boot_desc->heap_start:0
boot_desc->heap_end:0
boot_desc->argc:2
boot_desc->flags:0x5
boot_desc->core_mask:0x1
boot_desc->dram_size:512
boot_desc->phy_mem_desc_addr:0
boot_desc->debugger_flag_addr:0xa44
boot_desc->eclock:500000000
boot_desc->boot_info_addr:0x1001f0
boot_info->ver_major:1
boot_info->ver_minor:2
boot_info->stack_top:0
boot_info->heap_start:0
boot_info->heap_end:0
boot_info->boot_desc_addr:0
boot_info->exception_base_addr:0x1000
boot_info->stack_size:0
boot_info->flags:0x5
boot_info->core_mask:0x1
boot_info->dram_size:512
boot_info->phys_mem_desc_addr:0x24108
boot_info->debugger_flags_addr:0
boot_info->eclock:500000000
boot_info->dclock:266000000
boot_info->board_type:20002
boot_info->board_rev_major:2
boot_info->board_rev_minor:14
boot_info->mac_addr_count:3
boot_info->cf_common_addr:0
boot_info->cf_attr_addr:0
boot_info->led_display_addr:0
boot_info->dfaclock:0
boot_info->config_flags:0x8
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2014 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 5.6 (GENERIC) #3: Thu Aug 14 15:00:46 CEST 2014
r...@erl.jasper.la:/usr/src/sys/arch/octeon/compile/GENERIC
real mem = 247709696 (236MB)
avail mem = 245399552 (234MB)
warning: no entropy supplied by boot loader
mainbus0 at root
cpu0 at mainbus0: Cavium OCTEON CPU rev 0.1 500 MHz, Software FP emulation
cpu0: cache L1-I 32KB 8192 way D 16KB 4096 way, L2 128KB 32768 way
clock0 at mainbus0: int 5
iobus0 at mainbus0
octcf at iobus0 base 0x1d000800 irq 0 not configured
pcibus at iobus0 irq 0 not configured
cn30xxgmx0 at iobus0 base 0x1180008000000 irq 48
cnmac0 at cn30xxgmx0: RGMII, address dc:9f:db:80:3a:4d
atphy0 at cnmac0 phy 7: F1 10/100/1000 PHY, rev. 2
cnmac1 at cn30xxgmx0: RGMII, address dc:9f:db:80:3a:4e
atphy1 at cnmac1 phy 6: F1 10/100/1000 PHY, rev. 2
cnmac2 at cn30xxgmx0: RGMII, address dc:9f:db:80:3a:4f
atphy2 at cnmac2 phy 5: F1 10/100/1000 PHY, rev. 2
octrng0 at iobus0 base 0x1400000000000 irq 0
octhci at iobus0 irq 56 not configured
octrng0 at iobus0 base 0x1400000000000 irq 0
[0/276]
octhci at iobus0 irq 56 not configured
uar: ns16550, no working fifo
com0: console
com1 at uartbus0 base 0x1180000000c00 irq 35: ns16550, no working fifo
/dev/ksyms: Symbol table not valid.
vscsi0 at root
scsibus0 at vscsi0: 256 targets
softraid0 at root
scsibus1 at softraid0: 256 targets
root device: cnmac0
nfs_boot: using interface cnmac0, with revarp & bootparams
nfs_boot: client_addr=192.168.16.16
nfs_boot: server_addr=192.168.16.5 hostname=erl1
root on doan:/export/diskless/host/erl1
WARNING: No TOD clock, believing file system.
WARNING: CHECK AND RESET THE DATE!
swap on doan:/export/diskless/swap/erl1
Automatic boot in progress: starting file system checks.
setting tty flags
pf enabled
starting network
starting early daemons: syslogd pflogd ntpd.
starting RPC daemons:.
swapctl: adding doan:/export/diskless/swap/erl1 as swap device at priority 0
savecore: /bsd: kvm_read: version misread
checking quotas: done.
kvm_mkdb: can't open /dev/ksyms
clearing /tmp
kern.securelevel: 0 -> 1
creating runtime link editor directory cache.
preserving editor files.
starting network daemons: sshd smtpd sndiod.
/etc/rc.local[1]: cannot create /var/log/dmesg/2014-09-15T01:32.dmesg:
No such file or directory
starting local daemons: cron.
Mon Sep 15 01:32:30 PDT 2014
OpenBSD/octeon (erl1.redacted.net) (console)
login:
