hi
i allready read the threads here in this list because my problem is
similar but
not the the same.
the environment.
dsl provider in germany "NetCologne" they offer an full working /64 ipv6
net through slaac config.
i use an openbsd 5.8 beta 8 build a couple of day before )
physical interface are intel em
net.inet6.ip6.forwarding = 1
net.inet6.icmp6.nd6_debug=1
# cat /etc/hostname.em2
inet 192.168.0.2 255.255.255.252 NONE
up
# cat /etc/hostname.em0
inet 192.168.131.251 255.255.255.0 NONE
inet6 autoconf
!echo "setup ipv4 on NetCologene pppoe"
inet 0.0.0.0 255.255.255.255 NONE \
pppoedev em2 authproto pap authname 'nc-yyyyy...@netcologne.de' authkey
'xxxx' up
dest 0.0.0.1
!echo "setup ipv6 on NetCologne pppoe"
inet6 autoconf
!/sbin/route add -inet default -ifp pppoe0 0.0.0.1
!/sbin/route add -inet6 default -ifp pppoe0 ::0.0.0.1
# ifconfig pppoe0
pppoe0: flags=208851<UP,POINTOPOINT,RUNNING,SIMPLEX,MULTICAST,AUTOCONF6>
mtu 1492
priority: 0
dev: em2 state: session
sid: 0x508f PADI retries: 16 PADR retries: 0 time: 01:28:15
sppp: phase network authproto pap authname
"nc-glaesz...@netcologne.de"
groups: pppoe egress
status: active
inet6 fe80::214:b7ff:fe00:6163%pppoe0 -> prefixlen 64 scopeid 0xb
inet 84.44.157.221 --> 195.14.226.82 netmask 0xffffffff
inet6 2001:4dd0:af10:d604:214:b7ff:fe00:6163 -> prefixlen 64
autoconf pltime 604786 vltime 2591986
inet6 2001:4dd0:af10:d604:747a:f5e2:c201:b278 -> prefixlen 64
autoconf autoconfprivacy pltime 80714 vltime 599505
# route -n show
Routing tables
Internet:
Destination Gateway Flags Refs Use Mtu Prio Iface
default 195.14.226.82 UGS 1 2046 - 8 pppoe0
84.44.157.221 84.44.157.221 UHl 0 0 - 1 lo0
127/8 127.0.0.1 UGRS 0 0 32768 8 lo0
127.0.0.1 127.0.0.1 UHl 1 0 32768 1 lo0
192.168.0.0/30 192.168.0.2 UC 0 0 - 8 em2
192.168.0.2 00:14:b7:00:61:66 UHLl 0 0 - 1 lo0
192.168.0.3 192.168.0.2 UHb 0 0 - 1 em2
192.168.131/24 192.168.131.251 UC 2 0 - 8 em0
192.168.131.101 e8:03:9a:b4:f6:48 UHLc 2 767 - 8 em0
192.168.131.103 00:1d:7d:02:5a:e4 UHLc 0 0 - 8 em0
192.168.131.251 00:14:b7:00:61:63 HLl 0 0 - 1 lo0
192.168.131.255 192.168.131.251 UHb 0 0 - 1 em0
195.14.226.82 84.44.157.221 UH 0 0 - 8 pppoe0
224/4 127.0.0.1 URS 0 0 32768 8 lo0
Internet6:
Destination Gateway Flags Refs Use Mtu
Prio Iface
::/104 ::1 UGRS 0 0 32768 8
lo0
::/96 ::1 UGRS 0 0 32768 8
lo0
default ::1 UGS 0 12 - 8
pppoe0
default fe80::90:1a00:41a4:ecb0%pppoe0
UG 0 0 - 56 pppoe0
::1 ::1 UHl 15 0 32768 1
lo0
::127.0.0.0/104 ::1 UGRS 0 0 32768 8
lo0
::224.0.0.0/100 ::1 UGRS 0 0 32768 8
lo0
::255.0.0.0/104 ::1 UGRS 0 0 32768 8
lo0
::ffff:0.0.0.0/96 ::1 UGRS 0 0 32768 8
lo0
2001:4dd0:af10:d604:214:b7ff:fe00:6163
2001:4dd0:af10:d604:214:b7ff:fe00:6163 UHl 0 0 - 1 lo0
2001:4dd0:af10:d604:747a:f5e2:c201:b278
2001:4dd0:af10:d604:747a:f5e2:c201:b278 UHl 0 0 - 1 lo0
2002::/24 ::1 UGRS 0 0 32768 8
lo0
2002:7f00::/24 ::1 UGRS 0 0 32768 8
lo0
2002:e000::/20 ::1 UGRS 0 0 32768 8
lo0
2002:ff00::/24 ::1 UGRS 0 0 32768 8
lo0
fe80::/10 ::1 UGRS 0 0 32768 8
lo0
fe80::%em0/64 fe80::214:b7ff:fe00:6163%em0
UC 1 0 - 4 em0
fe80::214:b7ff:fe00:6163%em0 00:14:b7:00:61:63 HLl 0
0 - 1 lo0
fe80::ea03:9aff:feb4:f648%em0 e8:03:9a:b4:f6:48 UHLc 0
40 - 4 em0
fe80::%lo0/64 fe80::1%lo0 U 0 0
32768 4 lo0
fe80::1%lo0 fe80::1%lo0 UHl 0 0
32768 1 lo0
fe80::%pppoe0/64 fe80::214:b7ff:fe00:6163%pppoe0
U 0 0 - 4 pppoe0
fe80::90:1a00:41a4:ecb0%pppoe0 pppoe0 UHL 1 0
- 4 pppoe0
fe80::214:b7ff:fe00:6163%pppoe0 fe80::214:b7ff:fe00:6163%pppoe0
Hl 0 0 - 1 lo0
fec0::/10 ::1 UGRS 0 0 32768 8
lo0
ff01::/16 ::1 UGRS 6 0 32768 8
lo0
ff01::%em0/32 fe80::214:b7ff:fe00:6163%em0
UC 0 0 - 4 em0
ff01::%lo0/32 ::1 UC 0 0 32768 4
lo0
ff01::%pppoe0/32 fe80::214:b7ff:fe00:6163%pppoe0
UC 0 0 - 4 pppoe0
ff02::/16 ::1 UGRS 6 0 32768 8
lo0
ff02::%em0/32 fe80::214:b7ff:fe00:6163%em0
UC 0 0 - 4 em0
ff02::%lo0/32 ::1 UC 0 0 32768 4
lo0
ff02::%pppoe0/32 fe80::214:b7ff:fe00:6163%pppoe0
UC 0 0 - 4 pppoe0
until this point all works as expected .
i get the message a lot in /var/log/messages a lot of time.
nd6_lookup: failed to lookup fe80:b::90:1a00:41a4:ecb0 (if = pppoe0)
if i do an tcpdump -nevvvi pppoe0 i see the RA from netcologne include
the IPv6 Net for the lan.
so if i start the rtadvd -d em0 without counfg i see that he receive
the RA from ppoe but he dont deploy
the offered /64 network,
if i add the net by hand to the rtadvd ( addr= ) that it works a while (
until IP change from NetCologne )
what im doing wrong ?
Holger
p.s. i use 5.8-beta due hardware support for my embedded device ( thanks
sfire )
