On 13 September 2015 at 19:26, Toby Slight <[email protected]> wrote:
> On 13 September 2015 at 18:34, Toby Slight <[email protected]> wrote: > >> OK, so I finally managed to boot the 12th's snapshot on an EFI only T430. >> Weirdly enough one time it just worked, but when I tried again I got the >> same results as the 9th's snapshot installer. >> >> It seems that sometime the bootblocks get loaded, sometimes not, 9 times >> out of 10 I get http://i.imgur.com/Apfoe8r.jpg, then suddenly it will >> just work. Any idea why a successful boot appears to be so random? Also, is >> it normal that the resolution is a tiny cropped box in the middle of the >> screen? >> >> Anyway, once I'd apparently (and very much obliviously) cast the right >> mystical invocations to successfully boot the installer, I followed Chris' >> very clear and useful instructions, with some slight alterations, to do my >> usual encrypted softraid0 setup on one disk. >> >> One point I should note is that the newfs_msdos command was not available >> in the installer's path, I had to wait until after install and then call >> the binary from the installed sets - ie) /mnt/sbin/newfs_mkdos. >> >> Anyway, apart from that tiny hiccup, everything else worked as expected. >> However when I tried to boot the new install I ended up almost immediately >> at the ddb prompt, as pictured below: >> >> http://i.imgur.com/1sfqYQ8.jpg >> >> http://i.imgur.com/OcRNUyI.jpg >> >> I'm not a developer and don't know how to use ddb, so is there anything >> else I could do to provide you guys information and help debug the issue? >> >> When I rebooted again it seemed the process hung in a slightly different >> way: >> >> http://i.imgur.com/1Am1qNB.jpg >> >> Hope some of that might be helpful to some of you EFI wizards, and if >> not, I haven't nuked the disk yet, so if there's any ddb poking you'd like >> me to do, let me know. Cheers! >> > > Perhaps this may also be of interest - I get yet again different results > when booting the sp kernel from the bootloader prompt (the boot process got > a lot further this time strangely enough): > > http://i.imgur.com/bAE0qWp.jpg > > http://i.imgur.com/sg7Rxgv.jpg > > Again, in case it helps - managed to boot the ramdisk from my install successfully and get a dmesg: OpenBSD 5.8-current (RAMDISK_CD) #1245: Sat Sep 12 15:04:54 MDT 2015 [email protected]:/usr/src/sys/arch/amd64/compile/RAMDISK_CD real mem = 8384425984 (7996MB) avail mem = 8128602112 (7752MB) mainbus0 at root bios0 at mainbus0: SMBIOS rev. 2.7 @ 0xdae9c000 (68 entries) bios0: vendor LENOVO version "G1ETA8WW (2.68 )" date 03/06/2015 bios0: LENOVO 2349VFV acpi0 at bios0: rev 2 acpi0: tables DSDT FACP SLIC TCPA SSDT SSDT SSDT HPET APIC MCFG ECDT FPDT ASF! UEFI UEFI POAT SSDT SSDT UEFI DBG2 BGRT acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat cpu0 at mainbus0: apid 0 (boot processor) cpu0: Intel(R) Core(TM) i5-3230M CPU @ 2.60GHz, 2594.56 MHz cpu0: FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUS H,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX ,EST,TM2,SSSE3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,POPCNT,DEADLINE,AES,X SAVE,AVX,F16C,RDRAND,NXE,LONG,LAHF,PERF,ITSC,FSGSBASE,SMEP,ERMS,SENSOR,ARAT cpu0: 256KB 64b/line 8-way L2 cache cpu0: apic clock running at 99MHz cpu0: mwait min=64, max=64, C-substates=0.2.1.1.2, IBE cpu at mainbus0: not configured cpu at mainbus0: not configured cpu at mainbus0: not configured ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins acpiec0 at acpi0 acpiprt0 at acpi0: bus 0 (PCI0) acpiprt1 at acpi0: bus -1 (PEG_) acpiprt2 at acpi0: bus 2 (EXP1) acpiprt3 at acpi0: bus 3 (EXP2) acpiprt4 at acpi0: bus -1 (EXP3) pci0 at mainbus0 bus 0 pchb0 at pci0 dev 0 function 0 "Intel Core 3G Host" rev 0x09 "Intel HD Graphics 4000" rev 0x09 at pci0 dev 2 function 0 not configured xhci0 at pci0 dev 20 function 0 "Intel 7 Series xHCI" rev 0x04: msi usb0 at xhci0: USB revision 3.0 uhub0 at usb0 "Intel xHCI root hub" rev 3.00/1.00 addr 1 "Intel 7 Series MEI" rev 0x04 at pci0 dev 22 function 0 not configured em0 at pci0 dev 25 function 0 "Intel 82579LM" rev 0x04: msi, address 28:d2:44:44:38:e9 ehci0 at pci0 dev 26 function 0 "Intel 7 Series USB" rev 0x04: apic 2 int 16 usb1 at ehci0: USB revision 2.0 uhub1 at usb1 "Intel EHCI root hub" rev 2.00/1.00 addr 1 "Intel 7 Series HD Audio" rev 0x04 at pci0 dev 27 function 0 not configured ppb0 at pci0 dev 28 function 0 "Intel 7 Series PCIE" rev 0xc4: msi pci1 at ppb0 bus 2 sdhc0 at pci1 dev 0 function 0 "Ricoh 5U823 SD/MMC" rev 0x04: apic 2 int 16 sdmmc0 at sdhc0 ppb1 at pci0 dev 28 function 1 "Intel 7 Series PCIE" rev 0xc4: msi pci2 at ppb1 bus 3 iwn0 at pci2 dev 0 function 0 "Intel Centrino Advanced-N 6205" rev 0x34: msi, MIMO 2T2R, MoW, address 6c:88:14:d2:96:90 ehci1 at pci0 dev 29 function 0 "Intel 7 Series USB" rev 0x04: apic 2 int 23 usb2 at ehci1: USB revision 2.0 uhub2 at usb2 "Intel EHCI root hub" rev 2.00/1.00 addr 1 "Intel QM77 LPC" rev 0x04 at pci0 dev 31 function 0 not configured ahci0 at pci0 dev 31 function 2 "Intel 7 Series AHCI" rev 0x04: msi, AHCI 1.3 ahci0: port 0: 6.0Gb/s ahci0: port 1: 6.0Gb/s ahci0: port 2: 3.0Gb/s scsibus0 at ahci0: 32 targets sd0 at scsibus0 targ 0 lun 0: <ATA, Samsung SSD 850, EXM0> SCSI3 0/direct fixed naa.50025388a08bc16e sd0: 122104MB, 512 bytes/sector, 250069680 sectors, thin sd1 at scsibus0 targ 1 lun 0: <ATA, Samsung SSD 850, EXM0> SCSI3 0/direct fixed naa.50025388a08bc171 sd1: 122104MB, 512 bytes/sector, 250069680 sectors, thin sd2 at scsibus0 targ 2 lun 0: <ATA, KINGSTON SMS200S, 603A> SCSI3 0/direct fixed naa.50026b725703170d sd2: 57241MB, 512 bytes/sector, 117231408 sectors, thin "Intel 7 Series SMBus" rev 0x04 at pci0 dev 31 function 3 not configured isa0 at mainbus0 pckbc0 at isa0 port 0x60/5 irq 1 irq 12 pckbd0 at pckbc0 (kbd slot) wskbd0 at pckbd0: console keyboard efifb0 at mainbus0 wsdisplay0 at efifb0 mux 1: console (std, vt100 emulation), using wskbd0 uhub3 at uhub1 port 1 "vendor 0x8087 product 0x0024" rev 2.00/0.00 addr 2 uhub4 at uhub2 port 1 "vendor 0x8087 product 0x0024" rev 2.00/0.00 addr 2 softraid0 at root scsibus1 at softraid0: 256 targets sd3 at scsibus1 targ 1 lun 0: <OPENBSD, SR CRYPTO, 005> SCSI2 0/direct fixed sd3: 102405MB, 512 bytes/sector, 209727023 sectors root on rd0a swap on rd0b dump on rd0b -- 0x2b || !0x2b
