Hello @list,
perhaps I'm stupid but I've got a problem with two CARPed gateways
running 5.7-amd64 stable.
Hardware:
two supermicro-board machines with four network interfaces each (em0 ..
em3).
Networks:
LAN A : 172.16.210/24 via em0
LAN B : 172.16.0/24 via em1
direct connect for pfsync: 1.1.1.0/30 via em3
Gateway A setup ------- (master) -------
hostname.em0:
"inet 172.16.210.2 255.255.255.0"
hostname.em1:
"inet 172.16.0.30 255.255.255.0"
hostname.em3
"inet 1.1.1.1 255.255.255.252 1.1.1.3"
hostname.carp0
"inet 172.16.210.1 255.255.255.0 172.16.210.255 vhid 1 \
carpdev em0 pass gwvoip01carppass advskew 0"
hostname.carp1
"inet 172.16.0.29 255.255.255.0 172.16.0.255 vhid 2 \
carpdev em1 pass gwvoip01carppass advskew 0"
hostname.pfsync0
"up syncdev em3 syncpeer 1.1.1.2"
sysctl net.inet.carp ->
net.inet.carp.allow=1
net.inet.carp.preempt=1
net.inet.carp.log=7 #debugging
Gateway B setup ------- (backup) -------
hostname.em0:
"inet 172.16.210.3 255.255.255.0"
hostname.em1:
"inet 172.16.0.31 255.255.255.0"
hostname.em3
"inet 1.1.1.2 255.255.255.252 1.1.1.3"
hostname.carp0
"inet 172.16.210.1 255.255.255.0 172.16.210.255 vhid 1 \
carpdev em0 pass gwvoip01carppass advskew 100"
hostname.carp1
"inet 172.16.0.29 255.255.255.0 172.16.0.255 vhid 2 \
carpdev em1 pass gwvoip01carppass advskew 100"
hostname.pfsync0
"up syncdev em3 syncpeer 1.1.1.1"
sysctl net.inet.carp ->
net.inet.carp.allow=1
net.inet.carp.preempt=1
net.inet.carp.log=2
problem description ------------------
(remark: failover-switching works on both machines in both directions)
If one of the machines reboots, the local carp-interfaces stuck in
"INIT" state. Same behavior on both systems.
The log (A) after reboot:
carp: carp0 demoted group carp by -1 to 162 (carpdev)
carp: carp1 demoted group carp by -1 to 161 (carpdev)
carp: pfsync0 demoted group carp by -1 to 32 (pfsync bulk done)
carp: pfsync0 demoted group pfsync by -1 to 32 (pfsync bulk done)
carp: pfsync0 demoted group carp by -32 to 0 (pfsync init)
carp: pfsync0 demoted group pfsync by -32 to 0 (pfsync init)
If the carp-interfaces are subsequently restartet via netstart command,
all works like a charm again...
The log (A) after "sh /etc/netstart [carp0,carp1]":
carp0: state transition: INIT -> BACKUP
state transition: BACKUP -> MASTER
state transition: INIT -> BACKUP
state transition: BACKUP -> MASTER
No PF-ruleset-problem!
resulting question ---------------------
what the heck is going on here? ;-)
alternative: what did I forgot to configure?
Thanks for reading...
Andre Ruppert
